Level Calibration
This setting is set automatically by
Audyssey MultEQ
®
Speaker Setup function
you need to change the settings manually.
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
You can set the levels of front speakers A and front
speakers B independently. The other speakers (i.e.,
subwoofer, center, surround, surround back and front
high) use the same level settings for Speakers A and
Speakers B.
■
Left, Front Wide Left, Front High Left, Center
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right,
Surround Back Left, Surround Left
–12.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
■
Subwoofer 1
, Subwoofer 2
*1
–15.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
Note
• These settings cannot be calibrated when the AV receiver is
muted.
• Speakers that you set to "No" or "None" in the
"Speaker Configuration" cannot be selected
• The test tone is output at the standard level for THX, which is
0 dB (absolute volume setting 82). If you normally listen at
volume settings below this, be careful because the test tone will
be much louder.
• Speakers B cannot be selected if "Speakers Type(Front B)" is
set to "No"
(➔ page
*1
For the center speaker and subwoofer, the level settings made
by using the Home menu are saved in this menu
(➔ page
43).
*2
If the "Subwoofer" setting is set to "1ch", this setting cannot
be selected
(➔ page
Tip
• If you're using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
En
54
XT32 Room Correction and
(➔ page
33). For Speakers B,
*1*2
(➔ page
51).
52).
Equalizer Settings
With the Equalizer settings, you can adjust the tone of
speakers individually with a 7-band equalizer. The volume
of each speaker can be set.
The Equalizer settings only apply to Speakers A and
cannot be adjusted while Speakers B is selected.
■
Equalizer
Manual:
You can adjust the equalizer for each speaker
manually. Continue with the following procedure:
1
Press w to select "Channel", and then use
e/r to select a speaker.
2
Use q/w to select a frequency, and then use
the e/r to adjust the level at that frequency.
,
*1
The volume at each frequency can be adjusted
from –6dB to 0dB to +6dB in 1 dB steps.
Tip
• Low frequencies (e.g., 63Hz) affect bass sounds;
high frequencies (e.g., 16000Hz) affect treble
sounds.
3
Use q to select "Channel", and then use e/r
to select another speaker.
Repeat steps 1 and 2 for each speaker.
You cannot select speakers that you set to "No"
or "None" in the "Speaker Configuration"
52).
(➔ page
Off:
Tone off, response flat.
Note
• You can select: "63Hz", "160Hz", "400Hz", "1000Hz",
"2500Hz", "6300Hz", or "16000Hz". And for the subwoofer,
"25Hz", "40Hz", "63Hz", "100Hz", or "160Hz".
• When the Direct or Pure Audio listening mode is selected, the
equalizer settings have no effect.
• If "Audyssey" is enabled, it prevails over this setting
(➔ page
58).
THX Audio Setup
■
Surr Back Speaker Spacing
<1ft (<0.3m)
1ft-4ft (0.3m-1.2m)
>4ft (>1.2m)
You can specify the distance between your surround back
speakers. This setting is used by Speakers A and
Speakers B.
Note
• Cannot be set if:
– "Surround Back Ch" is set to "1ch"
– "Surround Back" is set to "None"
– "Powered Zone 3" is set to "Yes"
turned on
(➔ page
52).
(➔ page
52).
(➔ page
52).
(➔ page
51) and Zone 3 is
73).