Related Manuals for D-Link DES-1004
Summary of Contents for D-Link DES-1004
- Page 1 DES-1004/ DES-1008 10/100 Fast Ethernet Switch User’s Guide Rev. 01 (May, 1997) 6DES1008..01 Printed In Taiwan RECYCLABLE...
-
Page 2: Wichtige Sicherheitshinweise
Wichtige Sicherheitshinweise Bitte lesen Sie sich diese Hinweise sorgfältig durch. Heben Sie diese Anleitung für den spätern Gebrauch auf. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. -
Page 3: Limitation Of Liability
RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING OR OTHER HAZARD. LIMITATION OF LIABILITY IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA, LOSS OF PROFITS, COST OF COVER OR OTHER INCIDENTAL, CONSEQUENTIAL OR INDIRECT... -
Page 4: Limited Warranty
Customer bear the cost of sending back such products. A service charge may or may not be levied to Customer by D-Link. To find out if a service charge is levied or not, and the charged amount, read the RMA that is returned to Customer, or ask the D-Link office when an RMA is requested. - Page 5 D-Link Offices to Contact for Warranty Service: To obtain an RMA number for warranty service, contact the D-Link office nearest you. A list of contact addresses for D-Link’s international offices is found in the back of this User’s Guide. Your Warranty...
-
Page 6: Copyright Statement
Trademarks Copyright 1996 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced in any form or by any means... -
Page 7: Table Of Contents
Performance features... 4 UNPACKING AND SETUP ... 6 ... 6 NPACKING ... 7 ETUP ESKTOP OR HELF NSTALLATION (DES-1004)... 8 NSTALLATION (DES-1008) ... 9 NSTALLATION ... 11 OWER ON DES-1004... 11 DES-1008... 11 LED Indicators ... 11 Power Failure ... 12 IDENTIFYING EXTERNAL COMPONENTS... - Page 8 10/100 Fast Ethernet Switch User’s Guide LED I ... 16 NDICATORS CONNECTING THE SWITCH... 18 ... 18 WITCH ... 19 UB TO WITCH 10Base-T Hub ... 20 100Base-TX Hub... 20 (MDI-II) UB WITHOUT PLINK Using straight cable... 21 Using crossover cable... 21...
-
Page 9: About This Guide
DES-1004/ DES-1008. For simplicity and brevity, this manual discusses two 10/100 Fast Ethernet Switch models. The DES-1004 is a four port model, and the DES-1008 is an eight port model. These models are similar in every respect except for the number of ports. -
Page 10: Overview Of This User's Guide
LED indicators of the Switch. Chapter 4, Connecting the Switch. Tells how you can connect the DES-1004/ DES-1008 to your Ethernet network. Appendix A, Technical Specifications. Lists the technical (general, physical and environmental, and performance) specifications of the Switch. -
Page 11: Introduction
10/100 Fast Ethernet Switch User’s Guide NTRODUCTION This section describes the features of the DES-1004/ DES-1008, as well as giving some background information about Ethernet/ Fast Ethernet switching technology. Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need for high performance networks. -
Page 12: Switching Technology
Ethernet or Fast Ethernet LAN segments. Switching is a cost-effective way of increasing the total network capacity available to users on a local area network. A switch increases capacity and decreases network loading by making it possible for a local area network to be divided into different segments which don’t compete with each other for... -
Page 13: Features
The Switches with their small, compact size were specifically designed for small to large workgroups (the 4-port switch for smaller workgroups and the 8-port for larger workgroups). These Switches can be installed where space is limited; moreover, they provide immediate access to a rapidly growing network through a wide range of user-reliable functions. -
Page 14: Performance Features
Half-duplex operation. Uplink/ MDI-II (media dependent interface) another switch, hub or repeater. Please note that if you are using the uplink port, you will not be able to use port one (1x) because these ports are logically connected. - Page 15 10/100 Fast Ethernet Switch User’s Guide 8K active MAC address entry table per device with self learning and table aging. 8 MB packet buffer per device. Introduction...
-
Page 16: Unpacking And Setup
This User’s Guide Four rubber feet with adhesive backing Wall Mount Kit (DES-1004 only) which includes: two tapping screws and two plastic anchors If any item is found missing or damaged, please contact your local D-Link Reseller for replacement. NPACKING AND ETUP... -
Page 17: Setup
Setup The setup of the Switch can be performed using the following steps: The surface must support at least 1.2 Kg for the DES-1004 and 2.5 KG for the DES-1008. The power outlet should be within 1.82 meters (6 feet) of the device. -
Page 18: Wall Installation (Des-1004)
Figure 1 10/100 Fast Ethernet Switch installed on a Desktop or Wall Installation (DES-1004) The DES-1004 comes complete with a wall mount kit. This kit includes two screws and two plastic anchors. For a proper placement on the wall, follow... -
Page 19: Rack Installation (Des-1008)
The mounting brackets for the DES-1008 are an optional item and must be purchased separately from your local re-seller. brackets on the switch’s front panel (one on each side) and secure them with the screws provided. Unpacking and Setup 10/100 Fast Ethernet Switch User’s Guide... - Page 20 Figure 2A. Attaching the mounting brackets to the 10/100 Fast Ethernet Switch (for DES-1008) Then, use the screws provided with the equipment rack to mount the Switch in the rack. Figure 2B. Installing the DES-1008 Switch in an equipment rack...
-
Page 21: Power On
Power on DES-1004 The DES-1004 Switch can be used with AC power sources 100 - 240 VAC, 50 - 60 Hz. To turn the Switch on, plug one end of the power cord into the AC power connector of the Switch and the other end into the local power source outlet. -
Page 22: Power Failure
As a precaution, the Switch should be turned OFF in case of a power failure. For the DES-1004, disconnect the power cord from the local power source, and for the DES-1008, press the power switch to the off or “0” position. -
Page 23: Identifying External Components
Switch. Front Panel The front panel of the Switch consists of 4 (10/100 Mbps MDI-X) ports— DES-1004 or 8 (10/100 Mbps MDI-X) ports— DES-1008, 1 Uplink (MDI- II) port and LED indicators. A description of the ports appear in the Introduction of this User’s Guide (see Features, Chapter 1). -
Page 24: The Des-1008 Cable Organizer
This feature is not part of the DES-1004. The extra value of the cable organizer will be seen when all cables are laid out in a neat, orderly arrangement. -
Page 25: Des-1008
Power Switch. (DES-1008 only) This turns the Switch on and off. To turn on the system, press the switch to the “1” position; to turn off, press the switch to the “0” position. Note that on the DES-1004 a power switch is not provided. -
Page 26: Led Indicators
LED indicators for the Switch along with an explanation of each indicator. Figure 7 The DES-1004 Switch LED indicators Figure 8 The DES-1008 Switch LED indicators Power. This indicator operates when the Switch is turned on. If this indicator is not lit, check the AC power connector to ensure proper insertion of the power cord and that the power switch is turned ON. - Page 27 10/100 Fast Ethernet Switch User’s Guide is connected to a respective port or the uplink port, the LED indicator is OFF. Link/Act. These LED indicators are lighted up green when there is a secure connection (or link) to a device at any of the ports. The LED indicators blink green whenever there is reception or transmission (i.e.
-
Page 28: Connecting The Switch
A PC can be connected to the Switch via a two-pair Category 3, 4, 5 UTP /STP straight cable. The PC (equipped with a RJ-45 10/100 Mbps jack) should be connected to any of the four ports (1x -4x) for the DES-1004 or eight ports (1x - 8x) for the DES-1008. -
Page 29: Hub To Switch
Category 3, 4, 5 UTP/STP straight cable. The connection is accomplished from the hub’s uplink (MDI-II) port to any of the Switch’s (MDI-X) ports: 1x - 4x for the DES-1004 or 1x - 8x for the DES-1008. Connecting The Switch... -
Page 30: 10Base-T Hub
10/100 Fast Ethernet Switch User’s Guide Figure 10 DES-1008 Switch connected to a 10 or 100Base-TX Hub 10Base-T Hub For a 10 Base-T hub, the Switch’s LED indicators should illuminate the following: 100M LED speed indicator is OFF. Link/Act indicator is ON. -
Page 31: Hub Without Uplink (Mdi-Ii) Port
Using straight cable When using straight cable, The connection can be made from the uplink (MDI-II) port of the Switch to any port of the Hub (see figure 11). Using crossover cable When using crossover cable, the connection can be made from any (1x - 8x) port of the Switch to any port of the Hub (see figure 11). -
Page 32: Switch To Switch (Other Devices)
When using straight cable, this is done from the uplink (MDI-II) port of the Switch (Switch A) to any of the 10 Mbps or 100 Mbps (MDI-X) port of the other switch (switch B) or other devices (see figure 12). - Page 33 10/100 Fast Ethernet Switch User’s Guide 100 M is ON for 100Base-TX, otherwise OFF. Link/Act is ON. FDX/Col depends on the connected switch or other device. Connecting The Switch...
-
Page 35: Technical Specifications
IEEE 802.3 MAC layer frame size: 64 - 1518 Bytes Protocol: CSMA/CD Data Transfer Rate: Ethernet: 10 Mbps (half duplex) 20 Mbps (full duplex) Topology: Star General Technical Specifications 10/100 Fast Ethernet Switch User’s Guide ECHNICAL PECIFICATIONS Fast Ethernet: 100Mbps (half duplex) 200Mbps (full duplex) -
Page 36: Physical And Environmental
EIA/TIA- 568 100-ohm STP (100 m) 100Base-TX: 2-pair UTP Cat. 5 (100 m) EIA/TIA-568 100-ohm STP (100 m) Number of Ports: DES-1004: 4 x 10/100 Mbps ports DES-1008: 8 x 10/100 Mbps ports Media Interface MDI-II RJ-45 shared with port 1x Exchange:... - Page 37 MAC Address Learning: Technical Specifications 10/100 Fast Ethernet Switch User’s Guide Performance Store-and-forward DES-1004: 4 M bytes per device DES-1008: 8 M bytes per device 8 K entries per device 148,800 pps per port (for 100Mbps) Automatic update Max age: fixed...
-
Page 38: Pin Specification
10/100 Fast Ethernet Switch User’s Guide When connecting the DES-1004/ DES-1008 Switch to another switch, a bridge or a hub, a modified crossover cable is necessary. Please review these products for matching cable pin assignment. following diagram receptacle/connector and their pin assignments for the switch-to-network adapter card connection, and the straight/ crossover cable for the Switch-to- switch/hub/bridge connection. - Page 39 The standard Category 3 cable, RJ-45 pin assignment The following shows straight cable and crossover cable connection: Straight cable for Switch (uplink MDI-II port) to switch/Hub or Crossover cable for Switch (MDI-X port) to switch/hub or other network devices (MDI-X port) connection RJ-45 Pin Specification 10/100 Fast Ethernet Switch User’s Guide...
-
Page 40: Index
10/100 Fast Ethernet Switch User’s Guide 100 M (speed indicator) ... 17 100Base-T ... 1 AC inputs... 26 AC Power Connector... 15 AC power cord ... 6 Auto polarity ... 4 Cable Organizer... 14 Crossover cable ... 29 CSMA/CD Ethernet protocol ... 1 Data filtering ... - Page 41 Switch to Switch (other devices)22 Switching LAN technology ... 3 Switching Technology... 2 System Fan ... 15 Index 10/100 Fast Ethernet Switch User’s Guide Transmission Method ... 27 Unpacking ... 6 Uplink/ MDI-II ... 4 ventilation... 7 Wall Installation (DES-1004)... 8 Weight ... 27...
- Page 43 2180 Dunwin Drive, Unit # 6, Mississauga Ontario, L5L 5M8, Canada TEL: 1-905-828-0260 FAX: 1-905-828-5669 U.K. D-LINK (EUROPE) LTD. D-Link House, 6 Garland Road, Stanmore, London HA7 1DP U.K. TEL: 44-181-235-5555 FAX: 44-181-235-5500 GERMANY D-LINK (DEUTSCHLAND) GMBH I.G. Bachstra e 2265812 65830 Kriftel, Germany...
-
Page 45: Registration Card
3. What network protocol(s) does your organization use ? †XNS/IPX †TCP/IP †DECnet †Others_____________________________ 4. What network operating system(s) does your organization use ? †D-Link LANsmart †Novell NetWare †NetWare Lite †SCO Unix/Xenix †PC NFS †3Com 3+Open †Banyan Vines †DECnet Pathwork †Windows NT †Windows NTAS †Windows '95 †Others__________________________________________ 5.