Advertisement
Quick Links
TO REGISTER YOUR PUMP
SCAN THIS QR CODE OR VISIT
MDMINC.COM/PUMP-REGISTRATION
TYPE: END-SUCTION CENTRIFUGAL
MOTOR: NEMA 254/6JM-324/6JM
HORSEPOWER: 7.5HP TO 60HP
INLET: 4" FLANGED
DISCHARGE: 3" FLANGED
MATERIAL: VINYL ESTER AND POLYESTER THERMOSET
GLASS FILLED THERMOPLASTIC
Read completely before you install or operate your new pump. Do not allow the motor to become submerged.
PROUDLY MADE IN THE USA
Integrating Disruptive Technologies To Deliver Higher Efficiencies.
© MDM INCORPORATED
WWW.MDMINC.COM
INSTALLATION AND SERVICE MANUAL
Never run dry. Never exceed an internal case pressure of: 100 PSI.
4X3-9
®
FILL IN FOR FUTURE REFERENCE:
MODEL: ______________________________
SERIAL NUMBER: _______________________
DATE PURCHASED: ______________________
*MOTORS ARE SUBJECT TO CHANGE DUE TO
AVAILABILITY OR SPECIFICATION REQUIREMENTS.
HARDWARE: 316 STAINLESS STEEL
SEAL OPTIONS: IMPENATRA
III NON-METALLIC MECHANICAL SEAL
®
316SS REVERSE MOUNT MECHANICAL SEAL
ACCESSORIES: FIBERGLASS REDUCING OFFSET INLET STRAINER BASKET
VARIABLE FREQUENCY DRIVE
®
XXXXXXXXX
S/N: XXXX-XXXXXX
REV 2409
P.1
Advertisement
Related Manuals for MDM GENESYS 4X3-9
Summary of Contents for MDM GENESYS 4X3-9
- Page 1 Read completely before you install or operate your new pump. Do not allow the motor to become submerged. Never run dry. Never exceed an internal case pressure of: 100 PSI. PROUDLY MADE IN THE USA Integrating Disruptive Technologies To Deliver Higher Efficiencies. REV 2409 © MDM INCORPORATED WWW.MDMINC.COM...
-
Page 2: Electrical Connections
2. Check that the supply voltage matches the motor’s nameplate voltage. 3. Verify motor rotation with a phase rotation tester. Do not run pump dry. PROUDLY MADE IN THE USA Integrating Disruptive Technologies To Deliver Higher Efficiencies. REV 2409 © MDM INCORPORATED WWW.MDMINC.COM... - Page 3 ANCHOR 97077A180 FLAT WASHER 90107A033 HEX BOLT 93190A712 PUMP MOUNTING HARDWARE MCMASTER-CARR PART NUMBERS ANCHOR 97095A180 FLAT WASHER 90107A033 HEX BOLT 92186A720 PROUDLY MADE IN THE USA Integrating Disruptive Technologies To Deliver Higher Efficiencies. REV 2409 © MDM INCORPORATED WWW.MDMINC.COM...
- Page 4 RISER BLOCK 1/2" WRENCH TIGHTEN VOLUTE BOLTS THREADED ROD ASSEMBLY, LEFT 15/16" WRENCH TIGHTEN FLANGE NUTS / BOLTS THREADED ROD ASSEMBLY, RIGHT PROUDLY MADE IN THE USA Integrating Disruptive Technologies To Deliver Higher Efficiencies. REV 2409 © MDM INCORPORATED WWW.MDMINC.COM...
- Page 5 • If a VFD is utilized, make certain to use the jog function when testing rotation. DISASSEMBLY Disassembly is the reverse of assembly. PROUDLY MADE IN THE USA Integrating Disruptive Technologies To Deliver Higher Efficiencies. REV 2409 © MDM INCORPORATED WWW.MDMINC.COM...
-
Page 6: Maintenance
Viton is a registered trademark of the Chemours Corporation. ™ 3345 N. Cascade Ave • Colorado Springs, CO • 80907 Impenatra is a registered trademark of MDM Incorporated. ® Phone (719) 634-8202 • Fax (866) 425-1346 Genesys ® is a registered trademark of MDM Incorporated.
Need help?
Do you have a question about the GENESYS 4X3-9 and is the answer not in the manual?
Questions and answers