Page 1
NETWORK VIDEO RECORDER User Manual XRN-426S...
Page 2
❖ Design and specifications are subject to change without prior notice. You can download the latest version from the Hanwha Vision web site. (www.HanwhaVision.com) ❖ The initial administrator ID is “admin” and the password should be set when logging in for the first time.
Do not leave the battery in a high temperature environment. ● Before using this product, check if the latest version of this software is installed. Go to Hanwha Vision's website ● Do not leave the battery in a low-pressure environment.
Page 4
overview CAuTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ● ACCORDING TO THE INSTRUCTIONS. Do not ingest battery, Chemical Burn Hazard. ● This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause ●...
fuNCTIONS SuPPORTED by MODEl Model name XRN-426S Function Joystick Extended monitor Failover Alarm RAID Distributed recording iSCSI AI compatible function AI search Object detection AI recognition function LPR search Power supply redundancy Dewarping English _5...
overview CONTENTS OVERVIEW Important Safety Instructions Real-Time Event Monitoring Check Event List Product User Manual Description Target Audience Event Search How to Use the Product Event Instant Viewer Functions Supported by Model Stop Alarm Output Contents Camera Video Control Manual trigger Capture gETTINg STARTED Starting the system...
Page 7
AI SEARCH Screen Layout of the AI Search Setting the Network Person Search IP & Port Face Search DDNS & P2P Vehicle Search IP Filtering LP Search HTTPS 802.1x PlAy Screen Layout of the Play E-mail Play Search Results SNMP Time Line Adjustment DHCP Server Open Time Line Channel...
Page 8
overview SEARCH VIEWER Changing the Pattern of Split Screen Screen Layout of the Search Viewer Changing Overall Channel Aspect Ratio Time Search Full Screen Mode Event Search Setting up the Live Layout Text Search Check Layout List 100 Bookmark Search Add Layout and Set Name 100 Search Results Export Change of Layout Channel and Name...
Page 9
SETuP VIEWER 106 Screen Layout of the Setup Viewer ExPORT VIEWER 120 SEC Backup Viewer 106 Setting the Camera 120 Recommended System Requirements 106 Channel setup 120 Screen Layout of the Backup Viewer 106 Camera setup 107 Profile Setup 108 Camera Password APPENDIx 122 Using Virtual Keyboard 108 Setting the Recording...
getting started Starting the SyStem inStallation Wizard As shown below, proceed through each step of the <installation wizard>. 1. Connect the power cable of the recorder to the wall outlet. Install Wizard can only be accessed at factory reset. If you do not want to proceed, click <exit>. 2.
Page 11
3. Set the network connection type and the connection environment on the <network> screen, and then click the Setting the camera registration method <next>. This function is only available for products that support PoE. For products that support PoE, refer to the "Functions Supported by model"...
Page 12
getting started 5. Set the camera password in factory reset on the <Camera id/PW> screen. 7. To set the recommended resolution on the <resolution> screen, click <apply> followed by the <next> button. If ID/PW is already set in the camera, register the ID/PW and click <next>. ■...
9. On the <Channel setup> screen, you can view the camera videos registered to each channel in thumbnails along Camera SetUP with thumbnail information. To change the camera video position, select a video and drag and drop it to the desired When the installation wizard closes, the camera setup screen will automatically appear.
Page 14
getting started Configuring the Video environment Configuring the illumination Select the thumbnail of the channel whose settings you want to change and click < >. The setting window You can click <Setting> to change to the setting you want. that was classified according to the scene will appear. You can select items that are relevant to your channel.
ShUtting doWn the SyStem login To use the Recorder menu, you are required to login as a user that is authorized to access the applicable menu. 1. Select <Shutdown> at the top right of the screen. 1. Select <login> at the top right of the screen. 2.
live Shows the video of the camera connected to the recorder. Also, you can adjust the camera and check the network Item Description transfer status. Saves the recorded video of the selected channel in the designated path. SCreen layoUt oF the liVe Clears the alarm in the event list and stops the alarm/beep sound for the system status when it is emitted.
Checking the System Status Item Description The icon at the top of the screen indicates the status of the system. Displayed when there is software to update on the camera. Displayed when playing the layout sequence. Displayed when an error occurs in the internal memory. error information ●...
live Check Camera list Check multichannel Cameras list For multichannel cameras registered with the Wisenet protocol, the channel information will be displayed under Displays the camera type, status, and name registered in the recorder. the model name of the multichannel camera. Registered channel (recording channel) Unregistered channel...
live Screen menu icons on the live Screen After selecting the desired channel on the split mode, roll the mouse cursor over the screen to see the live screen You can check the status or operation with the icons on the live screen. menu.
live oSd information display Item Description You can show or hide the recording status, camera status, event display, etc. in the video window. Events from the recorder and camera are displayed in icons. Event Display To show or hide the OSD information, click < >...
Channel information display Check the Camera Status You can check the information of the video being recorded with each camera. You can check the status of all cameras connected to the recorder. To check the channel information, click < > at the bottom of the screen. To check the camera status, click <...
Page 22
live record Status network Status If you select <record> in the <Status> menu, you can check the profile, record type, frame rate (Input/Record), Select <network> in the <Status> menu to check the status of network bandwidth currently being received/ and bit rate (Limit/Input/Record) for each channel. transmitted.
CH10 CH11 CH12 CH13 CH14 CH15 CH16 Changing overall Channel aspect ratio ● Enable: Turns on/off the power supply to the camera. – Checked ( ): Power supply available CH19 CH19 Video screen ratio for all channels can be changed in live split screen mode. CH10 CH10 CH11...
live Full Screen mode Setting UP the liVe layoUt You can change to full screen mode, which has no top/bottom/left/right areas of the live screen. This section outlines how to select a series of channels based on their purpose/accessibility and monitor them in a single layout.
add layout and Set name dynamic layout You can set the size and position of the video assigned to the layout as desired. 1. Click < > to add a layout. ■ 2. Click < > to set the name for the added layout. The dynamic layout function can only be set on the primary monitor.
Page 26
live zooming in and out of Videos moving Videos You can enlarge or reduce the video by dragging a corner or vertex of the video in the desired direction. To move the video, click the video and then drag and drop it in the desired location. If you double-click the corner or vertex of the enlarged video area, the video will be reduced step by step.
Play layout Sequence real-time eVent monitoring You can automatically switch the layout list to a set time interval to view. Real-time events that occurred on the camera can be checked in the live video window and event list. ■ AI events are only available for products that support AI. ■...
live event Search alarm input filter Displays the only events for the alarm input numbers of the selected recorder. You can search events by camera, alarm input (recorder), and event type. To search for a specific event, click < > to select the event type and camera to browse. event filter Displays only selected events in the event list.
event instant Viewer Camera Video Control Select an event to check from the event list, and click < > to play the recorded video at the time the event By using the function icon of the video window, you can easily use the functions of capture, video zoom, PTZ camera occurred.
live Capture temperature detection mode You can take a screenshot of the current video of a specific channel selected on the live screen. For images that support the thermal imaging camera function, you can click the desired point to check the temperature information.
Ptz mode zoom in You can run PTZ control of the selected channel. You can zoom in or out the video via digital zoom. Select the desired channel and click < >. Select the desired channel and click < >. Enters the PTZ control mode.
live display text Change Channel aspect ratio You can monitor texts regarding the sales record received from POS in real time. You can change the aspect ratio of each channel. ■ Select the desired channel and click < >. This is executable when a text device is connected. ■...
PTZ driver (physical device). ■ It only supports a network camera with Hanwha Vision's PTZ function and a camera registered in the ONVIF. Group The group function enables you to group various presets before calling them in sequence.
live Using digital Ptz (d-Ptz) Function to delete a registered preset 1. Click < >. 1. Register a camera that supports the D-PTZ profile. ■ 2. Click < >. <delete preset> window will appear. In cameras that support the D-PTZ profile, you can use the D-PTZ function. 2.
exPorting the reCorded Video 3. After completing the export setup, select <Start>. ■ If there is no device to export, the <Start> button will be deactivated. You can search the storage device to be exported and export the recorded video of the desired time by layout or ■...
search time Search You can search recorded video by various conditions such as time, event, and export. You can search the recorded data by the desired date and time conditions. Screen Layout of the Search ■ The time displayed will be based on the time zone and daylight saving time (DST) applied time zone, so it may be displayed differently depending on whether the data time zone recorded at the same time and daylight saving time (DST) is applied.
event Search text Search You can search for various events by channel. You can search the data input to the POS device connected to the recorder. 1. Select <event search> in the <Search> menu. 1. Select <text search> in the <Search> menu. 2.
search export Search arB Search You can search the exported data on the connected storage device. Only data saved in recorder file format when You can search auto-recovery backup data stored on ARB storage devices. exported will be retrieved. 1. Select <arB search> in the <Search> menu. ■...
Bookmark Search Smart Search You can search for bookmarked data. You can search for events by selecting a region of interest, an exclusive region, or a virtual line from a recorded video at a specific time. ■ To use smart search, you need to set the area of the camera's “Motion Detection" or “IVA” to the entire area. However, if you want to search for cameras after Wisenet X series, you must select “Enable"...
AI search perSon Search If there is AI data recorded by the camera, you can search for images in various conditions such as people, faces, and vehicles. ■ In the recorded data, you can search for a person by any condition you want, such as gender, top/bottom color. This function is not supported in some models.
face Search vehicLe Search From the recorded data, you can search faces according to your desired conditions such as gender and age. You can search the vehicle by setting the vehicle type and color conditions from the recorded data. 1. Select <face search> in the <ai search> menu. 1.
AI search Lp Search You can search for vehicle license plates from the recorded data. 1. Select <Lp search> in the <ai search> menu. 2. Select a channel to search. ■ If you select a channel to search, you can change the channel display mode by clicking < >.
play You can play the recorded data and export the video you want during playback. item Description Screen Layout of the pLay Date/Time Set the date/time. Time line Move the playback position and display event data. You can change the number of channels displayed in the time line. ■...
play pLay Search reSuLtS play Button name and function paused state time Line adjustment You can move the playback position and zoom the time line in and out. Click the desired play position in the time line. ● The playback start position will be moved. ■...
Search reSuLtS export You can export the search results to a file. 1. Click the < > button. 2. Select a layout and channel to export. 3. Select a start date/time and an end date/time. ■ If you changed the time zone of the recorder, select whether to apply DST. 4.
setup Setting the camera Sets the camera, recording, event, device, network, and system environment. You can access to the channel setup, camera settings, and profiles and camera password-related settings. Screen Layout of the Setup Setting the channel You can register a network camera for each channel and make connection between. Setup >...
Page 47
automatic registration of network cameras ● Audio – If set to <on>, you can turn the audio of the channel ON/OFF on the Live screen. – If set to <off>, the channel's audio is off on the Live screen and not recorded. Status : Display the connection status.
Page 48
URL : Enter your RTSP access address. For more information, see your camera user manual. ● – Wisenet Multi-Channel : You can register Hanwha Vision's multi directional cameras and multi-imager cameras. A multi-channel camera is a camera that has multiple camera modules in one body. Auto- ID : Enter the camera ID.
Page 49
if you want to check the error details of camera registration network camera firmware upgrade If you failed to register a camera, the reason for the failure will be displayed. connection failed due to unknown error. : This message appears if the camera has failed to be registered ●...
setup Setting the camera functions ● SSNR : Adjusts the brightness by reducing noise and minimizing afterimages even in dark places. ● Sens-up : Automatically adjusts the shutter speed according to the brightness of the current light. You can set the camera while viewing the live video of the selected camera. ●...
Setting the profiles Setting the Live profile You can change the live transfer settings of the network camera. Setting the recording profile Setup > camera > profile setup > Live You can configure the video profile settings for instructing the network camera (connected to each channel) to make recording.
Page 52
setup Setting the remote profile editing the profiles You can set the video profile transmitted to the network. You can change the video settings of a registered network camera for each channel. Setup > camera > profile setup > remote Setup >...
Page 53
Dewarping Setup how to set WiseStream Press the <Dewarping> button at the bottom of the <Detailed profile configuration> window to go to the Function to analyze the complexity of the video and effectively reduce the data size while maintaining the distortion correction setup popup window for each channel.
setup Dynamic goV/fpS setup Setting camera password Dynamic GOV can be used to automatically change the length of GOV depending on the video condition. For You can change the passwords of all registered cameras at once. details, refer to the camera's help or the product's user guide. You can register the camera’s ID and password.
Setting the recorDing record Setup You can set the resolution and number of recordings for each channel when an event occurs or during a normal You can setup scheduled recording, event recording and other recording related settings. recording. You can check frame rates and data transfer amount of Full Frame and Key Frame recordings for each channel, record Schedule and set the transfer limit for recordings.
setup ■ Setting the eVent If a channel's data transfer exceeds defined allowed limit, then it may affect to other channels, and may force switching to <I-frame> recording even when the channel is configured to <Full frame> recording mode. For Key Frame recording channels, the icon for limited You can set the event-related settings such as whether or not an event is detected for each channel and whether an recording appears on the live screen's top side.
Page 57
motion ● BestShot : You can set the object to display the bestshot items. ■ Set the same as the item selected in <Object type> to display the best shot when an event is detected. Setup > event > event setup > motion ●...
Page 58
setup tampering Setup > event > event setup > iVa Setup > event > event setup > tampering IVA : You can set whether to enable intelligent video analytics. Tampering detection : You can set whether to enable tampering detection. ●...
event rule Setup Item Description You can set the event trigger and action rule to output an alarm when an event occurs. Video loss detection Setup > event > event rule setup SD Card Dynamic event Example) DigitalAutoTracking, Queue, ShockDetection, MaskDetection ObjectDetection Manual trigger Video loss recovered...
Page 60
setup register a new event rule – Mobile push notification : When an event occurs, the event push notification will be displayed on the connected smart phone. – Monitor event : When an event occurs, the screen of the corresponding channel will be displayed by switching to the live screen.
alarm input onVif Setup You can set the operation of the alarm sensor. You can set the details related to camera events registered with the ONVIF protocol. ■ This function is not supported in some models. Setup > event > onVif setup Setup >...
setup Setting the DeVice ● Storage Status : Displays the working status of a storage device. Click the <View> to display the storage status window. You can make the detailed settings for devices such as storage device and monitors. – Red : Displays the situation of video loss. –...
■ monitor The ARB feature is available only when your video is saved in the SD card after registering your Wisenet camera using the Wisenet protocol. This is only supported in SUNAPI 2.3.2 or later. ■ You can set the information displayed on the monitor as well as the output system. Set the profile bitrate used for recording a video in the SD card of camera to 6144 kbps or below.
setup Screen position setup text Some monitors many not display information (camera name, icon) about the Recording, depending on the You can set the POS device setting to send text information and text event information. condition. Then, you can change the display position of the data. Device Settings You can make detailed settings for the POS device connected to the recorder.
Page 65
registering a text Device text event Settings You can set the text to receive an alarm when an event occurs. Setup > Device > text > event ● Total amount : Set the condition of the total amount to be notified when a text event occurs. Check whether the total amount is used, and then select the base amount and range.
setup Setting the netWorK connecting and Setting the network Networking may differ from the connection method, check your environment before setting the connection You can set various network functions, such as monitoring live video by connecting to a network from a remote location mode.
Setting the Dhcp ip address of the Broadband router DDnS & p2p ● 1. To access the Broadband Router's configurations, open a web browser on the local PC that is connected to the A remote user can network a recorder using a DDNS address in a dynamic IP system. If you cannot connect with a Broadband Router and enter the router's address (ex : http://192.168.1.1).
Page 68
setup ■ connecting to the Viewer In a double NAT environment or if the router's port is not configured, the DDNS status will be displayed as <Successful>, but the DDNS connection from the viewer to the recorder may fail. ■ You must be connected to an external network for a DDNS connection.
ip filtering httpS You can prepare the list of IP addresses to allow or block access to a specific IP address. You can choose a secured connection system or install a certificate. Setup > network > ip filtering Setup > network > httpS ●...
setup 802.1x When connecting to a network, you can select whether to use the 802.1x protocol and install a corresponding When an event occurs, it can be configured to send the event image to the FTP server. certificate. Setup > network > ftp 802.1x is an authentication system between a server and a client, which prevents hacking, virus infection, and information leakage of transmitted and received network data.
e-mail event Setting You can set the interval and type of the event that will be sent to the user. You can send an e-mail to a Recorder-registered user at a specific time interval, or if an event occurs. Setup > network > e-mail > event Smtp Setting Sets the SMTP mail server.
setup Snmp Dhcp Server The SNMP protocol allows system or network administrators to remotely monitor and configure the network You can set the internal DHCP server and assign an IP address to the network camera. devices. network Setting Setup > network > Snmp Setup >...
checking the status to set troubleshooting You can check the IP address assigned to the current DHCP server, MAC address, and the connected network port 1. Set one recorder to <Standby> mode and the other recorder to <active> mode. information. 2.
setup in the case of standby mode Setting the SyStem Device list & status : Shows the status of the normal recorder currently connected to the standby recorder. To ● You can set the date, language, authority, etc. displayed when using the system, and query system information or log delete the normal recorder connected, click <Delete>...
user ● Holiday : A user can select specific dates as holidays according to their own preferences. Select a holiday from the calendar displayed by clicking <Setup>. You can manage users, such as adding or deleting users and granting different authorities for each user. –...
Page 76
setup user setting if you want to register a user You can create user groups and set authorities for each group. You can manage user information such as registering and deleting users in the created user group. Setup > System > user > user 1.
Page 77
restriction Settings if the user has restricted access Set user's restricted access or network restriction. If a general user selects a menu to which they do not have access, an access restriction confirmation window will be displayed. If all rights are restricted, only the accessible menu of the live screen menu will be displayed, and Items with restrictions will require logging in for use.
setup System management to upgrade the current software version You can check the current system version and update to a new version, export data, setting initialization, and Setup > System > System management > product information more. checking the System information You can check the current software version and MAC address before proceeding with the upgrade.
Settings Power down : If the power is off, the first alarm is generated. Select the <use the alarm output no. 1 when the ● device power is off> check box and click <apply> to clear all alarms set for alarm output 1, and then selecting You can export the information set in the recorder to a storage device and apply the same information to other alarm 1 with another alarm out will not be possible.
Page 80
setup checking the event log checking the export log You can search recorded events including alarms, camera events and video loss. You can search the user who performed the export and the execution time and details (time, channel, device, file It also shows the log and its timestamp.
starting web viewer What is Web VieWer? ConneCting Web VieWer Web Viewer is a software program with which the operator can access a remote Recorder for real-time monitoring, PTZ 1. Open your web browser and type the IP address or URL of Recorder into the URL address box. control (if configured) or search.
starting web viewer set the reCorder PassWord 2. Set the video recording method on the <storage> screen, and then click <next>. After factory reset, the password must be set for the recorder to access the web viewer. Enter the password of the admin account, and click <Login>. ●...
Page 83
4. Set the network connection type and the connection environment on the <network> screen, and then click 7. On the <Ch. registration> screen, select a camera to register from the searched camera list and then click <next>. <register>. Select a camera to register from the list and then click <Change iP>. After camera registration, click <next>.
starting web viewer 9. On the <easy connect> screen, a remote user can network a recorder in a dynamic IP system. CaMera setuP Click <enable> to test the connection to see if the current recorder can be connected remotely. When the When the installation wizard closes, the camera setup screen will automatically appear.
The ID of the connected user is displayed. Event list Shows a list of events that occurred on the camera. You are directly connected to the Hanwha Vision homepage (www.HanwhaVision.com). Layout list Displays the default layout and a list of created layouts.
live viewer CheCking the systeM status CheCking CaMera List The icon at the top of the screen indicates the status of the system. Displays the camera type, status, and name registered in the recorder. Name Description Live > List Displayed when a problem occurs with the recording status. Displayed when an error occurs in the power supply.
CheCking the aLL CaMera status network status Click the < > button, followed by the <network> tab. You can check the status of all cameras connected to the recorder. You can check the status of network bandwidth currently being received/transmitted. Live status Click the <...
live viewer Changing the Pattern oF sPLit sCreen Changing oVeraLL ChanneL asPeCt ratio Click the < > button and select the desired split screen. Video screen ratio for all channels can be changed in live split screen mode. The selected split screen is applied to the video window. Click <...
FuLL sCreen Mode setting uP the LiVe Layout You can change to full screen mode, which has no top/bottom/left/right areas of the live screen. This section outlines how to select a series of channels based on their purpose/accessibility and monitor them in a single layout.
live viewer Change of Layout Channel and name reaL-tiMe eVent Monitoring Real-time events that occurred on the camera can be checked in the live video window and event list. 1. Click < > after selecting a layout. ■ AI events are only available for products that support AI. 2.
Page 91
event search alarm input filter Displays the only events for the alarm input numbers of the selected recorder. You can search events by camera, alarm input (recorder), and event type. To search for a specific event, click < > to select the event type and camera to browse. event filter Displays only selected events in the event list.
live viewer event instant Viewer LiVe sCreen Menu Select an event to check from the event list, and click < > to play the recorded video at the time the event After selecting the desired channel on the split mode, roll the mouse cursor over the screen to see the live screen menu. occurred.
CaMera Video ControL instant Viewer During monitoring, you can rewind 1 minute before playback. By using the function icon in the video window, you can easily enable functions such as screenshot, video rotation, and PTZ control. Select the desired channel and click < >.
live viewer Ptz Mode zoom in You can run PTZ control of the selected channel. You can zoom in or out using the mouse wheel. Select the desired channel and click < >. If you scroll up using the mouse wheel, the selected video screen is enlarged by 10%, and a thumbnail window is displayed.
Channel aspect ratio Ptz ControL You can change the aspect ratio of each channel. Ptz Control Menu Select the desired channel and click < >. If the connected network camera is a PTZ camera, the < > icon is displayed in the camera list. When the It changes to the actual proportion of the video.
live viewer using digital Ptz (d-Ptz) function to delete a registered preset 1. Click < >. 1. Register a camera that supports the D-PTZ profile. ■ 2. Select the preset to delete, and click <delete>. In cameras that support the D-PTZ profile, you can use the D-PTZ function. 2.
exPorting Video You can export the recorded video by manually inputting the desired channel, date, and time. 1. Click the < > button. 2. Select a layout to export and select the desired channel. 3. Set the start date/time and end date/time. ■...
search viewer tiMe searCh You can search and play the recorded video stored in the recorder by connecting the recorder remotely. You can search the recorded data by the desired date and time conditions. sCreen Layout oF the searCh VieWer ■...
eVent searCh text searCh You can search for various events by channel. You can search the data input to the POS device connected to the recorder. 1. Select <event search> in the <search> menu. 1. Select < text search> in the <search> menu. 2.
search viewer bookMark searCh searCh resuLts exPort You can search for bookmarked data. Search results of events, texts and bookmarks can be exported to a file. example) bookmark search result export 1. Click < > in the search results list. 1.
AI search viewer Person searCh If there is AI data recorded by the camera, you can search for images in various conditions such as people, faces, and vehicles. ■ In the recorded data, you can search for a person by any condition you want, such as gender, top/bottom color. This function is not supported in some models.
AI search viewer FaCe searCh VehiCLe searCh From the recorded data, you can search faces according to your desired conditions such as gender and age. You can search the vehicle by setting the vehicle type and color conditions from the recorded data. 1.
LP searCh searCh resuLts exPort You can search for vehicle license plates from the recorded data. Search results such as people, faces, and vehicles can be exported to a file. example) Person search results export 1. Click < > in the search results list. 1.
play PLay searCh resuLts exPort Video by seCtion setuP You can play the recorded data and export the video you want during playback. You can select the desired section from the time line or search list during video playing and export it to a file. 1.
Play button name and Function Paused state Playback state Name Description Previous event Go to the previous event video. Previous frame Moves backward to the key frame (I-frame). Playback Play the video. Next frame Moves forward one frame or more. Next event Go to the next event video.
setup viewer setting the CaMera You can configure the Recorder settings remotely on the network. You can check a list of cameras that are connected to the Recorder and configure the necessary settings. sCreen Layout oF the setuP VieWer For details, refer to the "setup > setting the Camera" page in the Table of Contents. Channel setup You can register a network camera for each channel and make a connection between them.
When you click the <Camera webviewer> button, a new camera web browser window is opened. Profile setup ● – This is not supported if the camera is connected to the RTSP protocol. You can set the profile for a network camera. –...
setup viewer remote setting the reCording You can set the video profile transmitted to the network. For details, refer to the "setup > setting the recording" page in the Table of Contents. record schedule If you set a recording schedule for a specific date and time, the recording will start at that specific time. setup >...
record options setting the eVent You can set the hard disk recording option. For details, refer to the "setup > setting the event" page in the Table of Contents. ■ You can set the recording duration separately for each channel. event setup setup >...
Page 110
setup viewer Motion detection tampering detection You can change the settings for motion detection events. You can change the tampering detection event setup. ■ Detailed video analysis can be set by accessing the Camera webviewer. Video loss detection You can change the video loss detection event setup. You can change the settings for Intelligent Video Analytics (IVA) events.
event rule setup onViF setup You can set the event trigger and action rule to output an alarm when an event occurs. You can set the camera registered with the Onvif protocol. setup > event > event rule setup setup > event > onViF setup alarm input schedule You can set the operation of the alarm sensor.
setup viewer setting the deViCe Monitor You can set the information displayed on the monitor as well as the output system. You can check a list of devices that are connected to the Recorder and configure the necessary settings. For details, refer to the "setup > setting the device" page in the Table of Contents. setup >...
text setting the netWork You can set the POS device text display and event text settings. For details, refer to the "setup > setting the network" page in the Table of Contents. setup > device > text iP & Port device A remote user can access the Recorder via the network to check the current mode and the IP address.
setup viewer ddns & P2P httPs A remote user can network a recorder using a DDNS address in a dynamic IP system. If you cannot connect with a You can select a security connection system or install public certificates. dynamic IP, you can easily access using a P2P service. setup >...
Page 115
event You can set the event interval and specify which events the server sends mails for. When an event occurs, you can create settings related to the FTP server to which images will be transferred. setup > network > FtP recipient You can set groups and recipients to receive emails.
setup viewer snMP status You can check the IP and MAC currently used through the DHCP server, and the connected network port. Using the SNMP protocol, the system or network administrator can remotely monitoring the network devices and sets the environment. setup >...
setting the systeM user You can manage users, such as adding or deleting users and granting different authorities for each user. You can configure the various settings of the Recorder system. For details, refer to the "setup > setting the system" page in the Table of Contents. setup >...
setup viewer restriction settings settings You can set the user permission. Using a storage device, you can apply the current configuration of Recorder to another Recorder. Press the Initialization button to return the network settings to their factory default state. Items in the <exception>...
Page 119
event log The event log lists recorded events, such as sensor events, camera events, or image losses. export log You can search the user who performed the export and the execution time and details (time, channel, device, file type). English _119...
export viewer seC baCkuP VieWer screen Layout of the backup Viewer You can play a file that is backed up in the format of SEC. Backup in SEC format produces backup data file, library file and self-executable viewer file. If you run the backup file viewer, the backup data file will be played. XRN-1620B2_CAM 01 2020-05-14 20 :54 :13 recommended system requirements...
Page 121
Name Description Saves the current video's image as in an image file. Supports JPEG file format. Screen Printout Prints out the current screen. You should have installed the appropriate printer driver before you can print out the screen. A toggle button. Each time you press this button, the audio output will toggle between activated and deactivated.
appendix using VirtuaL keyboard troubLeshooting Problem Action Live video will be slow or cut off. ● The frame number set for multiple data transmission set in camera or network environment could differ from the actual rate of transmission. Click < >...
Page 123
Problem Action Problem Action The camera is not connected or the PC fails to connect to the ● Check if the network cable is connected properly. Recording does not work. ● If your player does not display a Live image at all, that indicates recording does not work so first check if you see an image on the screen.
Page 124
appendix Problem Action The recording screen will slow down. ● Check whether the recording performance specifications for each HDD condition match the actual recording settings. For details, refer to the "Setup > Setting the Recording” page in the Table of Contents. If the data volume of a video exceeds the playing performance, only the main frame is played.
Need help?
Do you have a question about the XRN-426S-1T and is the answer not in the manual?
Questions and answers