Husqvarna 130 Mark II Operator's Manual
Husqvarna 130 Mark II Operator's Manual

Husqvarna 130 Mark II Operator's Manual

Hide thumbs Also See for 130 Mark II:

Advertisement

Quick Links

130, 135 Mark II
EN
Operator's manual
10-24
H13038HV

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 130 Mark II and is the answer not in the manual?

Questions and answers

Summary of Contents for Husqvarna 130 Mark II

  • Page 1 130, 135 Mark II Operator's manual 10-24 H13038HV...
  • Page 8 Ø...
  • Page 10: Table Of Contents

    Contents Introduction..............10 Transportation...............20 Safety................11 Storage................. 20 Assembly..............15 Technical data.............. 20 Operation..............15 Accessories..............22 Maintenance..............18 Declaration of Conformity..........23 Introduction Operator's manual The initial language of this operator's manual is English. Operator's manuals in other languages are translations from English.
  • Page 11: Safety

    Product damage (Fig. 16) Do not use with one hand We are not responsible for damages to our product if: (Fig. 17) Do not let the guide bar tip touch an • the product is incorrectly repaired. object. • the product is repaired with parts that are not from the manufacturer or not approved by the (Fig.
  • Page 12 • The product can eject objects and cause injuries. can eject and cause injury or damage. Unwanted Obey the safety instructions to decrease the risk of material can wind around the chain and cause injury or death. damage. • Do not go away from the product when the engine •...
  • Page 13 To prevent kickbacks, skating, bouncing and • Always stop the engine before you move the product. dropping • Make sure you firmly plant your feet on the ground • While the motor runs, make sure to hold the product and distribute your weight evenly. tightly.
  • Page 14 To examine the stop switch • Before you refuel, open the fuel tank cap slowly and release the pressure carefully. To start a cold engine on page 1. Start the engine. See • Do not add fuel to the engine in an indoor area. Not 16 .
  • Page 15: Assembly

    • During transportation or storage of the product, use • Do not use waste oil. Waste oil can be dangerous a transportation guard or case to move the product. to you and can cause damage to the product and environment. Assembly 7.
  • Page 16 2. Pull the choke control out and up. CAUTION: Always use air-cooled 3. Push the air purge bulb 6 times. (Fig. 41) two-cycled engine oil of high quality. Other oils can cause damage to the 4. Hold the body of the product on the ground with your left hand.
  • Page 17 1. Put the lower end of the spiked bumper at the CAUTION: Do not pull the starter correct felling hinge width. rope until it stops. Do not let go of the 2. Push against the front handle with your left hand and starter rope when it is fully extended.
  • Page 18: Maintenance

    • If the log has support on the two ends, cut 1/3 • If you buck a log on a slope, always stay on the the diameter from the top. Complete the cut by uphill side of the log. Cut through the log while you underbucking the lower 2/3 of the log to touch the keep complete control of the product.
  • Page 19 To sharpen the saw chain • Do maintenance on the spark plug when: • the power level in the engine is low. The cutter • it is hard to start the engine. The cutting part of the saw chain is called the cutter and •...
  • Page 20: Transportation

    Use a flat file and depth gauge tool to adjust the depth 5. Make sure that you can pull the saw chain round freely by hand and that it does not sag. (Fig. 71) gauge. To lubricate the cutting equipment 1.
  • Page 21 135 Mark II Idle speed, min (rpm) 2800–3200 2800–3200 Maximum engine power acc. to ISO 1.5/2.0 @ 9000 1.6/2.1 @ 9000 7293, kW/hp @ min (rpm) Ignition system Spark plug NGK BPMR7A, BRISK HQT-1R NGK BPMR7A, BRISK HQT-1R Electrode gap, mm Fuel and lubrication system Fuel tank capacity, liter/cm 0.35/350...
  • Page 22: Accessories

    Length Pitch Gauge Max. nose radius Type Drive link count 14 inch 3/8 inch 0.050 inch Husqvarna H37 16 inch Husqvarna S93G Saw chain filing and saw chain combinations Chain type Round file Side plate Top plate File guide Depth...
  • Page 23: Declaration Of Conformity

    Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under our sole responsibility that the product: Description Gasoline Chainsaw Brand Husqvarna Platform / Type / Model Platform H13038HV, representing model 130, 135 Mark II...
  • Page 24 UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Gasoline Chainsaw Brand Husqvarna Platform / Type / Model Platform H13038HV, representing model 130, 135 Mark II Identification...
  • Page 25 862 - 007 - 26.07.2024...
  • Page 26 862 - 007 - 26.07.2024...
  • Page 27 862 - 007 - 26.07.2024...
  • Page 28 Original instructions 1143966-26 2024-08-05...

This manual is also suitable for:

135 mark ii

Table of Contents