WARNING: Risk of injury or property damage. Kohler Co. shall not be liable under its warranty or Please read all instructions thoroughly before otherwise for personal injury or damage caused by beginning installation, including the following any such unauthorized modification.
Follow the sections that pertain Kohler Co. reserves the right to make changes in to your particular installation. This will help you avoid product characteristics, packaging, or availability at any costly mistakes.
3” 1” 6-1/2” 6-1/2” OPT. C L OF SHOWER 84” ARM (1/2” I.P.S.) C L OF SUPPLY OPT. FITTING 4” 3-1/4” C L OF SPOUT 18” 1-1/2” O.D. 2-7/8” 3/8” 3” 1-1/2” I.P.S. THR’D. Kohler Co., Kohler, WI U.S.A. 114329-2-...
E. ELECTRICAL REQUIREMENTS The installation must have a Class A Ground-Fault Circuit-Interrupter (GFCI). The GFCI protects against line-to-ground shock hazard. Use a 120 V, 20 A, 60 Hz dedicated service for the whirlpool. Kohler Co., Kohler, WI U.S.A. 114329-2-...
NOTICE: Make sure the unit is within the installation area before final framing is completed. The unit will not fit through a standard door opening. Kohler Co., Kohler, WI U.S.A. 114329-2-...
When unit is installed where drain connections are accessible from below: Connections can be easily made from underneath the unit. Kohler Co., Kohler, WI U.S.A. 114329-2-...
B. PROTECT WHIRLPOOL UNIT Position a drop cloth or similar material in the bottom of the unit. Be careful not to scratch the surface of the product. Kohler Co., Kohler, WI U.S.A. 114329-2-...
Attach the unit to the 2x2 brace and toe plate previously installed around the recess rough opening. Use #6 large-head galvanized nails or #8 x 1” sheet metal screws across the top and bottom, and up both sides. Kohler Co., Kohler, WI U.S.A. 114329-2-...
B. PUMP BANDING STRAP CUT Shipping Bracket (leave attached NOTICE: This step is necessary to make your to bath) Kohler whirlpool operate more quietly. Pump Banding Straps Use tin snips to cut the two banding straps. These banding straps secure pump whirlpool-mounted shipping bracket.
Wire grounding adapter. Bonding (Earthing) Lug* Your Kohler whirlpool bath is equipped with a cord and plug. All wiring of the pump and control has been completed at the factory. A licensed electrician must Pump install a GFCI-protected, 120 V, 20 A, grounded outlet.
Grab bars can also be installed directly to the module, providing the proper fastening device is selected to securely attach the bar to the unit. Manufacturer’s suggestions concerning grab bar installation must be carefully followed. Kohler Co., Kohler, WI U.S.A. 114329-2-...
Position the shower rod so the shower curtain hangs inside the bath. E. SHOWER DOOR INSTALLATION Shower doors for this unit are available from the Kohler Co. Contact your dealer for more information on shower door availability and installation. When shower doors are to be installed on this bath...
Reduce Add Air whirlpool action, Air and rotate trim ring Water Water counterclockwise. To reduce air and water, turn it clockwise. Shut off whirlpool. Restart whirlpool after 20 minute cycle is complete. Kohler Co., Kohler, WI U.S.A. 114329-2-...
Insert the Flexjet into the housing, and lightly push and rotate the Flexjet until it snaps into position. Do not force the Flexjet. O-Ring (Must Be NOTE: When installed correctly, the Flexjet should turn Lubricated) smoothly both clockwise and counterclockwise. Kohler Co., Kohler, WI U.S.A. 114329-2-...
B. TROUBLESHOOT WHIRLPOOL SYSTEM This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or a qualified electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor. SYMPTOMS PROBABLE CAUSES RECOMMENDED ACTION 1.
Need help?
Do you have a question about the Sonata K-1563-H and is the answer not in the manual?
Questions and answers