Table of Contents
Advertisement
Available languages
Available languages
Quick Links
VE1120-D Series PIR Detector Installation Sheet
EN DE
1
3
© 2020 Carrier
2
4
20 m range (65 ft. 7 in.)
12 m (39 ft. 4 in.)
10 m (32 ft. 9 in.)
8 m (26 ft. 2 in.)
6 m (19 ft. 8 in.)
4 m (13 ft. 1 in.)
2 m (6 ft. 6 in.)
0 m
2 m (6 ft. 6 in.)
4 m (13 ft. 1 in.)
6 m (19 ft. 8 in.)
8 m (26 ft. 2 in.)
10 m (32 ft. 9 in.)
12 m (39 ft. 4 in.)
(optimum) 2.4 m
(7 ft. 10 in.)
1.2 m (3 ft. 11 in.)
4 m (13 ft. 1 in.)
P/N 146626999-1 (ML) • REV G • ISS 04DEC20
1 / 10
(1)
(2)
(3)
20.0 m (65 ft. 7 in.)
Advertisement
Table of Contents
Related Manuals for Aritech VE1120-D Series
Summary of Contents for Aritech VE1120-D Series
- Page 1 VE1120-D Series PIR Detector Installation Sheet EN DE 20 m range (65 ft. 7 in.) 12 m (39 ft. 4 in.) 10 m (32 ft. 9 in.) 8 m (26 ft. 2 in.) 6 m (19 ft. 8 in.) 4 m (13 ft. 1 in.) 2 m (6 ft.
- Page 2 J1: Not used VE1120-D VE1120AM-D J3 and J4: See Figure 7. CV + polarity CV – polarity P/N 146626999-1 (ML) • REV G • ISS 04DEC20 2 / 10...
-
Page 3: En: Installation Sheet
VE1120-D VE1120AM-D < 33 Ω Normal < 33 Ω Normal larm larm VE1120-D VE1120AM-D Ω Normal 4.7 k Ω Normal 4.7 k larm kΩ larm kΩ Tamper Ω Tamper Short Ω Short AM/TF Ω Normal 4.7 k larm kΩ Ω Normal 4.7 k Tamper... -
Page 4: Dip Switch Settings
• To install the detector: Controls the AM relay functionality during the NIGHT mode together with SW1. Lift off the custom insert and remove the screw (see Figure 2, step 1). The WT input controls the LED functionality together with the Using a screwdriver, carefully prise open the detector (see D/N input. -
Page 5: Led Indication
VE1120AM-D requirements and provisions of the Directive Detector PIR with AM 2014/30/EU and/or 2014/35/EU. For more information see firesecurityproducts.com or Signal processing www.aritech.com. Range 20 m REACH Product may contain substances that are also Optical 11 high-density mirror curtains Candidate List substances in a concentration Memory above 0.1% w/w, per the most recently published... - Page 6 Wählen Sie die gewünschten Steckbrücken- und DIP- Contact information Schalter-Einstellungen aus (siehe Abb. 5). Weitere Informationen finden Sie in Abschnitt “Steckbrücken- firesecurityproducts.com or www.aritech.com Einstellungen” unten. Entfernen Sie die Abdeckungen und bringen Sie bei Bedarf die Aufkleber an (Abb. 6 zeigt ein Beispiel).
-
Page 7: Led-Anzeige
• Der Melder befindet sich im Betrieb „Gehtest aus“ (LEDs • Für die erweiterte Einstellung (SW 2 ist eingeschaltet sind deaktiviert), wenn der WT-Eingang mit +12 V (Ein)) muss die Ursache des AM-Alarms beseitigt werden, bevor der AM-Reset durchgeführt werden kann. (Anschlussklemme 2) verbunden ist. -
Page 8: Technische Daten
Carrier Fire & Security Americas Corporation Inc. 13995 Pasteur Blvd Palm Beach Gardens, FL 33418, USA Kontaktinformation BEVOLLMÄCHTIGTER EU REPRÄSENDANT: Carrier Fire & Security B.V. firesecurityproducts.com oder www.aritech.com Kelvinstraat 7, 6003 DH Weert, Niederlande P/N 146626999-1 (ML) • REV G • ISS 04DEC20 8 / 10... - Page 9 Declaration of Conformity The VE1120-series is suitable for use in alarm systems designed to comply with PD6662 at security grade 2 and VE1120-D environmental class II. VdS Nr: G110507 The VE1120AM-series is suitable for use in alarm systems designed to comply with PD6662 at security grade 3 and Klasse: B environmental class II.
- Page 10 P/N 146626999-1 (ML) • REV G • ISS 04DEC20 10 / 10...
Need help?
Do you have a question about the VE1120-D Series and is the answer not in the manual?
Questions and answers