Main Unit Display - Pioneer DJM-900NXS Operating Instructions Manual

g DIGITAL, CD/ LINE, PHONO, LINE, USB */* selector switch (page 14)
Select the input source of each channel from the components connected to this
unit.
h TRIM control (page 14)
Adjusts the level of audio signals input in each channel.
i EQ/ISO (HI, MID, LOW) controls (page 14)
These adjust the sound quality of the different channels.
j Channel Level Indicator (page 14)
Displays the sound level of the different channels before passing through the
channel faders.
k COLOR controls (page 15)
These change the parameters of the SOUND COLOR FX of the different
channels.
l Channel Fader (page 14)
Adjusts the level of audio signals output in each channel.
m CROSS FADER ASSIGN (A, THRU, B) selector switch (page 14)
Set the output destination of each channel to [A] or [B].
n Crossfader (page 14)
Outputs audio signals assigned by the crossfader assign switch correspond-
ing to the curve characteristics selected by [CROSS FADER] (Crossfader Curve
Selector Switch).
o MASTER LEVEL controls (page 14)
Adjusts the sound level output from the [MASTER] channel.
p Master Level Indicator (page 14)
Displays the sound level output from the [MASTER] channel.
q BALANCE controls (page 15)
Adjusts the left/ right balance of the sound output from the [MASTER1] termi-
nals, etc.
r MONO, STEREO selector switch (page 15)
Switches the sound output from the [MASTER1] terminals, etc., between mon-
aural and stereo.
s BOOTH MONITOR controls (page 15)
Adjusts the level of audio signals output at the [BOOTH] terminal.
t EQ CURVE (ISOLATOR, EQ) selector switch (page 14)
Switches the function of the [EQ/ISO (HI, MID, LOW)] controls.
u CH FADER ( , , ) selector switch (page 14)
Switches the channel fader's curve characteristics.
v CROSS FADER ( , , ) selector switch (page 14)
This switches the crossfader curve characteristics.
w ON/OFF (UTILITY) button
— ON/ OFF: Turns the MIDI function on/ off (page 17).
— UTILITY: Displays the [USER SETUP] or [CLUB SETUP] screen (page 23).
x START/ STOP button (page 17)
Sends the MIDI start/ MIDI stop signals.
y LFO FORM (WAKE UP) button
— LFO FORM: When [MIDI LFO] is selected at BEAT EFFECT, the MIDI sig-
nal's waveform switches each time the button is pressed (page 20).
— WAKE UP: Cancels the auto standby mode (page 23).
z Main unit display
A X-PAD (page 16)
Adjusts the quantitative parameter of the BEAT EFFECT function.
B BEAT c, d buttons (page 16)
Sets the beat fraction for synchronizing the effect sound.
C TAP (ENTER) button
— TAP: When the BPM measurement mode is set to [TAP], the BPM is input
manually by tapping the button with a finger (page 16).
— ENTER: Used to change this unit's settings (page 23).
D QUANTIZE button
! Used to change this unit's settings (page 23).
! When the QUANTIZE function is turned on for BEAT EFFECT, the effect is
applied to the sound without going off tempo when the currently playing
track. (page 16).
E AUTO/TAP button (page 16)
Switches the BPM measurement mode.
F DELAY, ECHO, SPIRAL, REVERB, TRANS, FILTER, FLANGER,
PHASER, ROBOT, MELODIC, SLIP ROLL, ROLL, REV ROLL, SND/RTN
(MIDI LFO) selector switch (page 16)
Switches the BEAT EFFECT effect type.
G 1, 2, 3, 4, MIC, CF.A, CF.B, MASTER selector switch (page 16)
Switches the channel to which the BEAT EFFECT is to be applied.
H TIME control (page 16)
Adjust the BEAT EFFECT's time parameter.
I LEVEL/ DEPTH control (page 16)
Adjusts the BEAT EFFECT's quantitative parameter.
J ON/ OFF button (page 16)
Turns the BEAT EFFECT function on/ off.
Do not pull on the channel fader and crossfader knobs with excessive force. The
knobs are not designed to be removed. Pulling the knobs strongly may result in
damaging the unit.
13
En