UniPOS 7201M Instruction Manual

7000M.
:
.
A ,
( .4/2 .1), DIN .
.
.
5.6 k .
- R ( ) B ( ).
(
UniTALK.
. ,
.
:
-
- „ " ( )
- „ "
- " / "
- " " ( )
-
C
:
-
(
,
1.
2.
3.
R - 5.6 k
:
„
8000D
- FD3050
-
:
1.
"
2.
" ".
1.
2.
36
,
-
,
. -
.
Производител: УниПОС ЕООД, Р България, 5800 Плевен, ул.Сан Стефано 47
,
( .1).
, ( .6/5
, EOL-2 (
(R ) (+), (B)
).
-
- .1, .1 - .3,
(18-30)V
DC
:
≤ 2 mA
(3-13) mA
(14-46) mA
≥ 47 mA
(18-22) V
DC
(0,8-1,5) mm²
IP 30
- 10º 45º
) ≤ 95%
92x60x22 mm
0,078 kg
( .4, .1)
( .5/6, .1).
4.
.
"
EOL-2
.
(
10s,
".
:
-
-
. -
,
,
http://www.unipos-bg.com
GENERAL DESCRIPTION
The adapter is designed to support a conventional re alarm line in the addressable loop at system 7000M.
Note:The zener barrier supports only one explosion-proof re detector, it is also necessary to change the re
current setting.
.1)
The adapter board is mounted in a plastic box ( g.1). The box allows installation on a wall through holes
(pos. 4/2 g.1) as well as on a DIN rail. For the convenience of the user, the terminal block (pos. 6/5 g.1) is
. 2) realized by connection terminals. On the terminal block are the terminals for connection to the signal circuit
(-) and the line of conventional re detectors.
The adapter is equipped with resistance of
terminals - R (red) and B (black). The red lead (R) connects to (+) and the black lead (B) to (-) at the end of the
conventional line (it is not included).
.
Communication between the control panel and the adapter is carried out on by the signal loop through the
.1 specialized UniTALK information exchange protocol. The adapter is powered by the signal loop. For
short-circuit protection, there is a built-in isolator - on the signal loop and current protection on the
conventional line. Two LEDs, red mode Fire - pos.1, g.1 and yellow mode Fault - pos.3, g.1 gives informa-
tion about the status of the device.
TECHNICAL DATA
Supply voltage:
- Signal loop
Current consumption in the conventional line in the condition:
- „Fault mode" (cut o )
- „Normal state"
- "Fire mode"
- "Fault mode" (short circuit)
- Conventional line voltage
Connecting Cables cross section
,
Type of connection :
- signal loop
Ingress protection
Operating temrerature range
Relative humidity resiatance (no condensation)
Dimensions
Weight
DIN .
INSTALLATION
The device is installed in a place protected from moisture by embedding in an additional box or DIN rail.
1. Fasten the device in the place chosen for the purpose through the holes (pos. 4, g. 1)
2. Lead and connect the cables to the terminals (pos. 5/6, g. 1).
.
3. Perform electrical installation according to gure 4.
The R - 5.6k termination element connects to the base of the last re detector in the conventional line.
Using this type of connection in case of sensor removal the panel will go o Fault "liner open.
Note: The use of type 8000D diode bases is required to detect a "Fire Detector Removed" fault in the
40 .
conventional line. Use EOL-2.
- When using conventional Manual Call Point 3050, must set the current to 40mA.
- It is not necessary to consider the conditional beginnings and ends of the contours.
TESTING
The adapter is tested as part of the site's re alarm system or during maintenance in the following sequence:
1. A re alarm is activated from the conventional re alarm line (required time for operation by conventional
1s ).
detectors no more than 10s, conventional manual call point less than 1s). The adapter should go into the "Fire" state.
. 2. A reset command is sent from the re control panel to the tested adapter. It should settle into a "Normal" state.
SERVICE SCHEDULE
It is done by authorized personnel and includes the following activities:
1.Inspection for visible physical damage
2.Testing in real conditions
WARRANTY
The warranty period is 36 months from the date of sale. The manufacturing company guarantees the normal
operation of the device, provided that the requirements for operation from this instructional manual are met.
The manufacturing company does not bear warranty obligations for malfunctions caused by mechanical
.
stress, use of the device not intended or in the case of changes and modi cations carried out after production.
The manufacturing company bears warranty responsibility only for damage to the device caused by the fault
,
, of the company itself.
5.6 k in case of using an end element EOL-2 (Fig. 2) with two
- monthly
- monthly
Manufacturer: UniPOS Ltd., 47 San Stefano Street, Pleven 5800, Bulgaria, http://www.unipos-bg.com
(18-30) V
DC
≤ 2 mA
(3-13) mA
(14-46) mA
≥ 47 mA
(18-22) V
DC
(0,8-1,5) mm²
Shielded,double wired
IP 30
- 10º 45º
≤ 95%
92x60x22 mm
0,078 kg