PESA UCI-2000-SMPTE Quick Start Manual

Es-bus routing switcher protocol converter

Advertisement

Quick Links

UCI-2000-SMPTE ES-Bus
Routing Switcher Protocol Converter
Quick-Start Guide
S
O
A
ERVICE AND
RDERING
SSISTANCE
PESA Switching Systems
103 Quality Circle, Suite 210
Huntsville AL 35806 USA
www.pesa.com
M
O
AIN
FFICE
Tel: 256.726.9200
Fax: 256.726.9271
S
D
ERVICE
EPARTMENT
Tel: 256.726.9222 (24/7)
Toll Free: 800.323.7372
Fax: 256.726.9268
Email: service@pesa.com
Document Number:
81-9059-0575-0 Rev. C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UCI-2000-SMPTE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for PESA UCI-2000-SMPTE

  • Page 1 UCI-2000-SMPTE ES-Bus Routing Switcher Protocol Converter Quick-Start Guide ERVICE AND RDERING SSISTANCE PESA Switching Systems 103 Quality Circle, Suite 210 Huntsville AL 35806 USA www.pesa.com FFICE Tel: 256.726.9200 Fax: 256.726.9271 ERVICE EPARTMENT Tel: 256.726.9222 (24/7) Toll Free: 800.323.7372 Fax: 256.726.9268 Email: service@pesa.com...
  • Page 2 No part of this publication (including text, illustrations, tables, and charts) may be reproduced, stored in any retrieval system, or transmitted in any form or by any means, including but not limited to electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of PESA Switching Systems, Inc.
  • Page 3: Table Of Contents

    CHAPTER 6: REAR CONNECTOR PIN-OUTS...........12 COM1 A COM2 ..................12 COM4 – D ..............13 IAGNOSTICS ONNECTION COM3 – PESA PRC B ............13 ONNECTION CHAPTER 7: CABLE CONNECTIONS ..............14 SMPTE ES-B PESA M ..............14 US TO PESA SMPTE ES-B ..............16 Proprietary Information of PESA Switching Systems...
  • Page 4 81-9059-0575-0 R UCI-2000-SMPTE ABLE OF ONTENTS CONT CHAPTER 8: UCI-2000-SMPTE PROTOCOL CONVERTER......17 - SMPTE ES-B PESA NSTALLATION AND NITIALIZATION ROCEDURE US TO ......................17 - PESA SMPTE/EBU ES- NSTALLATION AND NITIALIZATION ROCEDURE .....................20 Proprietary Information of PESA Switching Systems...
  • Page 5 -Party Routers............7 Table 5: Number of Controlled 3 -Party Levels............8 Table 6: DIP Switch S4 Settings, SMPTE to PESA Mode ...........9 Table 7: DIP Switch S4 Settings, PESA to SMPTE Mode ...........9 Table 8: COM1, COM2 Connector Pin-out..............12 Table 9: COM4 Connector Pin-out ................13...
  • Page 6 -Party Routers............7 Table 5: Number of Controlled 3 -Party Levels............8 Table 6: DIP Switch S4 Settings, SMPTE to PESA Mode ...........9 Table 7: DIP Switch S4 Settings, PESA to SMPTE Mode ...........9 Table 8: COM1, COM2 Connector Pin-out..............12 Table 9: COM4 Connector Pin-out ................13...
  • Page 7: Chapter 1: Preface - About This Manual

    VERVIEW This manual provides detailed instructions for the installation, operation, and maintenance of PESA’s Premiere Series Matrix Switchers. It is the responsibility of all personnel involved in the installation, operation, and maintenance of the equipment to know all the applicable safety regulations for the areas that they will be working in.
  • Page 8: Chapter 2: Introduction

    PESA C US TO ONTROL The ES-Bus to PESA control mode allows the UCI-2000-SMPTE to control up to four levels of PESA PRC-based routing switchers from a 3 -Party control system employing the SMPTE/EBU ES-Bus control protocol. Each of the four additional PESA levels can support a matrix size of 512x512 inputs and outputs.
  • Page 9: Pesa To Es-Bus Control Mode

    PESA Control System and cannot share an existing level with a PESA router or the system will not operate properly Figure 2 depicts a typical system block diagram of the PESA to ES-Bus control mode. PRC Bus...
  • Page 10: Chapter 3: Hardware Configuration

    CHAPTER 3: HARDWARE CONFIGURATION 3.1 S ETTING THE OPERATING MODE Dipswitch S1 on the UCI-2000-SMPTE pc board is used to set the card’s operating mode. Available operating modes for the UCI-2000-SMPTE are listed in Table 1. S1-8 S1-7 S1-6 S1-5 S1-4 S1-3 S1-2 S1-1...
  • Page 11: Setting The Prc Base Strobe Control Level And Number Of Controlled Levels

    3.2.1 SMPTE ES-Bus To PESA Mode Switches 1 – 6 of dipswitch S2 set the starting (base) strobe number of the controlled PESA matrices using a binary representation according to the following table (refer to Table 2). Valid level numbers are 1 – 63. (ON is to the right when viewing from above and the rear connectors are at the top of the board).
  • Page 12: Number Of Controlled Pesa Levels

    81-9059-0575-0 R UCI-2000-SMPTE Switches 7 and 8 of S2 set the number of controlled PESA matrices according to the following table (refer to Table 3): S2-7 S2-8 UNCTION UCI Controls 1 Level UCI Controls 2 Levels UCI Controls 3 Levels...
  • Page 13: Pesa To Smpte Es-Bus Mode

    8, all 3 -Party routers are set to start at level 1 regardless of where they "really" exist in the PESA control system. The UCI-2000 automatically offsets the base PRC strobe number when...
  • Page 14: Rd -Party Levels

    (refer to Table 5): S6-5 S6-6 UNCTION UCI Controls 1 Levels UCI Controls 2 Levels Number of Controlled 3 -Party Levels ABLE All of the other switches on S6 should be in the OFF position. Proprietary Information of PESA Switching Systems...
  • Page 15: Setting The Operation Of The Com1 And Com2 Serial Ports

    Switches 1 and 2 of dipswitch S4 are used to enable or disable the COM1 serial port on the back of the UCI-2000-SMPTE chassis. Switches 3 and 4 of S4 are used to select between RS232 and RS422 operation for the COM1 and COM 2 serial ports respectively;...
  • Page 16: Chapter 4: Software Configuration

    CHAPTER 4: SOFTWARE CONFIGURATION 4.1 SMPTE ES-B PESA M To enable the new PESA routers in the system, they must be added to the configuration in the 3 -Party control system software. The PESA routers are added and configured exactly as if they were Native 3 -Party routers.
  • Page 17: Chapter 5: Redundant Operation

    UCI-2000-SMPTE CHAPTER 5: REDUNDANT OPERATION The UCI-2000-SMPTE (see Figure 3) is capable of fully redundant operation when two cards are installed in the dual controller chassis. The front panel toggle switch is used to select one of three redundancy modes: Active, Standby and Automatic.
  • Page 18: Chapter 6: Rear Connector Pin-Outs

    6.1 COM1 A COM2 (Refer to Table 8.) RS232 F RS422 F Ground RXD (in) RX+ (in) TXD (out) TX- (out) Ground Ground Ground Ground RX- (in) TX+ (out) Ground COM1, COM2 Connector Pin-out ABLE Proprietary Information of PESA Switching Systems...
  • Page 19: Com3 - Pesa Prc Bus Connection

    TXD (out) Ground COM4 Connector Pin-out ABLE Typically a Null-Modem cable is used between the UCI2000 and a PC type COM port. 6.3 COM3 – PESA PRC B ONNECTION (Refer to Table 10.) RS422 F Ground TX+ (out) RX- (in)
  • Page 20: Chapter 7: Cable Connections

    See Figure 4 and perform the following sequence for Control Cabling Connections, SMPTE ES-Bus to PESA Mode: COM1: PRC - Connect to PESA Routers, loop between frames. Pin for Pin cable. COM2: RS422 ES-Bus connection (38400, Odd, 8, 1). Pin as required.
  • Page 21 81-9059-0575-0 R UCI-2000-SMPTE SYSTEM V CONTROL (37-pin): Not Used Connect the UCI-2000-SMPTE to the PESA routing switcher(s) using the standard 9-pin PESA PRC cable (pin-to pin). Connect the PESA UCI-2000-SMPTE to the 3 -Party routing system controller using a custom-made RS422 cable. Refer to the UCI-2000...
  • Page 22: Pesa To Smpte Es-Bus Ode

    Odd, 8, 1). Pin as required. COM3: PRC - Connect to PESA 3500/3500+/3500Pro Controller SYSTEM V CONTROL (37-pin): Not Used Connect the PESA 3500 series controller to the UCI-2000-SMPTE using the standard 9-pin PESA PRC cable (pin-to pin). Connect the PESA UCI-2000-SMPTE to the 3 -Party routing switcher(s) using a custom-made RS422 cable.
  • Page 23 UCI-2000-SMPTE protocol conversion board. This procedure is performed with the UCI-2000-SMPTE powered up and connected to the 3 -Party Controller and all PESA routing switchers with the appropriate cables. If your system contains redundant UCI-2000-SMPTE controller cards, this procedure must be performed on each card separately.
  • Page 24: Base Control Level

    Level 62 Level 63 Base Control Level ABLE • Switches 7 and 8 of S2 set the number of controlled PESA matrices according to the following table (refer to Table 12): S2-7 S2-8 UNCTION Controls 1 Level Controls 2 Levels...
  • Page 25: Uci-2000-Smpte Operating Modes

    Press and hold the front panel Reset Button for about 1 second, then release. The board will now query each PESA router. The TX led will indicate data activity on the PRC Bus. When it is finished, all front panel LEDs will turn off (except for the power LED).
  • Page 26 This document describes the installation procedure for commissioning a new UCI-2000-SMPTE protocol conversion board. This procedure is performed with the UCI-2000-SMPTE powered up and connected to the PESA System Controller and all 3 -Party routing switchers with the appropriate cables. If your system contains redundant UCI-2000-SMPTE controller cards, this procedure must be performed on each card separately.
  • Page 27: Rd -Party Routers

    Number of Controlled 3 -Party Levels ABLE Turn ON all switches on dipswitch S1 to re-initialize the board’s internal memory to factory defaults. Set the front panel toggle switch to the AUTO or ACTIVE setting. Proprietary Information of PESA Switching Systems...
  • Page 28: Uci-2000-Smpte Operating Modes

    -Party routers communicate using RS232, turn on switch #4 on S4. Install the UCI-2000-SMPTE card in the chassis and apply power (if necessary). Verify that the Power led is illuminated. Press and hold the front panel Reset Button for about 1 second, then release.

Table of Contents