PESA QuStream Integrity CS Series Quick Start Manual

I CS S
NTEGRITY ERIES
S
A2HD516 P
TART
ROCESSOR
Step
U
1
NPACK THE
P R
ROCESSOR ACK
Carefully unpack your Integrity CS Unit from shipping container
and verify package contents against contents listed below.
Visually inspect the unit for any signs of damage in shipment or
transit.
If any components are missing or damaged, contact QuStream
Customer Service.
1
P C :
ACKAGE ONTENTS
U
NPACK
S
HIPPING
C
ONTAINER
E
THERNET
C
OAXIAL
P (RJ45)
OWER
J
UMPER
J
C UMPER
ORD
C
ABLE
C
ABLE
MATING AUDIO
CONNECTORS
Q S
UICK TART
(A
TTACHED TO REAR
G
UIDE
PANEL AUDIO
)
CONNECTORS
2
V A I S A A
ERIFY LL TEMS HOWN BOVE RE
I W U
NCLUDED ITH NIT
If any components are missing or damaged, contact QuStream
Customer Service by phone or e-mail.
Customer Service: 1+ (256) 726-9222
Toll Free: (800) 323-7372 (US and Canada)
Fax: 1+ (256) 726-9268
Email: service@qustream.com
Step
2
G A
ET CQUAINTED
The Integrity CS A2HD516 is a self-contained format converter
and audio embedder/de-embedder. It accepts an input of
composite (NTSC/PAL) analog video or SD-SDI digital video
and produces outputs of HD-SDI, SD-SDI and option outputs
selectable as SD-SDI or composite analog.
The included side-column keyer accepts an input of HD SDI
video.
Inputs are provided for both AES and analog audio sources for
embedding. De-embedded audio is available as both AES
pairs and analog, selectable from any de-embedded channel
Quick-Start Guide
Step
2
G A
ET CQUAINTED
U
NIT
R P L
EAR ANEL AYOUT
Your Integrity CS A2HD516 is composed of a 1RU rack frame with a power supply and three
processing modules, installed in card slots on the rear of the chassis. An illustration of the rear
panel layout is shown below.
REDUNDANT EXTERNAL
MAIN POWER
POWER SYNC
CONNECTOR
CONNECTOR CONNECTOR
IN 1 IN 2 OU T 1A OUT 1B OU T 2A
ETHERNET FORMAT CONVERTER MODULE
POWER
CONNECTORS
SWITCH
F P L
RONT ANEL AYOUT
In most installations, the processor control panel is installed directly to the chassis frame. If
your system is equipped with the remote panel option, a blank front panel with status LEDs is
attached to the chassis. Whether local or remote, the control panel layout is as shown in the
illustration below.
Bypass Test Preset Hue
Input
Sel
Ref
Freeze Setup A1
Step
3
I R
NSTALL
Your Integrity CS Series processing product requires installation of rear panel jumpers for proper
operation. These jumper cables are removed for shipping, but are included in the package with
the processor.
Refer to the following figure, and perform the steps to install these necessary jumper cables prior
to use of the processor.
IN 1 IN 2 OUT 1A OUT 1B OUT 2A
SUPPLIED ETHERNET
CABLE JUMPER
Your Integrity CS Processor WILL NOT function unless these connections are completed.
Locate supplied coaxial cable jumper and supplied Ethernet cable jumper shipped with your
Integrity processor.
Install coaxial jumper between connector labeled Output (OUT) 2 on frame sync module and
connector labeled Input (IN) 2 on format converter module. Refer to figure when installing this
cable.
If you are using the LOCAL control panel on the front of the frame to control this unit, install
Ethernet cable jumper between the two Ethernet (RJ45) port connectors on rear panel of
processor. If you are using a REMOTE control panel over the facility LAN, use an Ethernet switch
or hub to provide an active network connection to BOTH rear panel Ethernet ports.
(C .)
ONT
FRAME SYNC MODULE
A NA LOG AU DIO 1,2,3,4 A ES A AES B VID A SDI IN VID B OU T 1 OU T 2
DL DL AES
C H1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 REF
AN ALOG IN A NA LOG OUT
OUT 2B OPT ION A OPT ION B GEN L K (1,2,3,4) (1,2,3,4) AU X 1/ 2 IN 3/4 IN 1/ 2 OU T 3/ 4 OUT
AUDIO MODULE
Video Gain Black Chroma
Menu
Take/Enter
Back Audio A2 A3 A4
P J
EAR ANEL UMPERS
ANALOG AUD IO 1,2,3,4 AES A AES B VID A SD I IN VID B O UT 1 O UT 2
DL DL AES
CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 REF
ANALO G IN ANALO G OUT
OUT 2B OPTION A OPTION B GENLOCK
( 1,2,3,4) (1,2,3,4) AUX 1/ 2 IN 3/ 4 IN 1/ 2 O UT 3/ 4 OUT
SUPPLIED COAXIAL
CABLE JUMPER
!! NOTE !!
Step
4
M A2HD516 C
OUNT
Considerations for mounting location include proximity to signal sources/destinations, availability
of primary power and availability of a source of external sync.
Mount the chassis frame in an equipment rack and secure frame to rack using four rack mount
screws.
Do not apply power until all external connections are made and verified.
Step
5
V /A C
IDEO UDIO ONNECTIONS
!! NOTE !!
Your A2HD516 Processor is shipped from the factory with the UDC operating mode selected.
This mode allows the processor to function as an analog or SD-SDI to HD converter
WITHOUT using the included side column keyer function.
If you wish to use the side column keyer, you MUST provide an HD input signal for use as the
keyer insert video source, and you MUST change the processor to the UCP operating mode as
shown in Step 8 of this guide. If UCP is selected as the operating mode and an HD signal is
not applied to the key video input connector, the A2HD516 WILL NOT function properly!!
Complete video and audio connections to the A2HD516 using the diagrams below as a
reference. Highlighted connection points indicate major function connections.
F S M C
RAME YNC ODULE ONNECTIONS
SD-SDI
AES 3/
SIGNAL
AES 1 DOLBY-E
ANALOG AUDIO ANALOG AUDIO AES 2
INPUT
INPUTS 1 & 2 INPUTS 3 & 4 INPUT INPUT INPUT
ANALOG AUDIO 1,2,3,4 AES A AES B VID A SDI IN
COAX JUMPER TO FORMAT
CONVERTER MODULE
F C C
ORMAT ONVERTER ONNECTIONS
COAX JUMPER FROM
A
FRAME SYNC MODULE
SIDE COLUMN
KEYER VIDEO
SD-SDI
HD-SDI
INPUT
OUTPUTS OUTPUTS
(SEE NOTE
1 2
1 2
ABOVE)
IN 1 IN 2 OUT 1A OUT 1B OUT 2A OUT 2B
A M C
UDIO ODULE ONNECTIONS
ANALOG AUDIO
ANALOG AUDIO
OUTPUTS AES 4
INPUTS
5 & 6 7 & 8 1 & 2 3 & 4 INPUT
AES
DL DL
REF
CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4
ANALOG IN ANALOG OUT
(1,2,3,4) (1,2,3,4)
AUX 1/2 IN
Audio Module Connector Pin-Outs Shown on Next Page
Part No. 81-9059-0647-0 Rev. B
F
HASSIS RAME
SD-SDI OUTPUT OF
ANALOG
SIGNAL CONVERTED ANALOG
SIGNAL
INPUT
VID B OUT 1 OUT 2
A
JUMPER SELECT
SD-SDI or ANALOG
EXTERNAL
OUTPUTS
SYNC INPUT
1 2
OPTION A OPTION B GENLOCK
AES 1
AES 5 AES 2
INPUT OUTPUT OUTPUT
3/4 IN 1/2 OUT 3/4 OUT