Page 3
Do not install near any heat source. Only use attachments/accessories specified by the manufacturer. Clean only with dry cloth. Do not defeat the safety purpose of the polarized or grounding‐type plug. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the unit. SERVICE INFORMATION (QUALIFIED PERSONNEL ONLY): Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. Only use replacement parts recommended by PESA. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry. Proprietary Information of PESA...
Page 4
09/1/2012 LIMITATION OF LIABILITY All information, illustrations, and specifications contained in this publication are based on the latest product information available at the time of publication approval. The right is reserved to make changes at any time without notice. DISCLAIMER OF WARRANTY IN NO EVENT SHALL PESA SWITCHING SYSTEMS, INC. BE LIABLE FOR ANY PARTY OR ANY PERSON, EXCEPT FOR CERTAIN WARRANY PROGRAM OFFERED BY THE LOCAL DEALER OF PESA, FOR THE CASES BUT NOT LIMITED TO THE BELOW: 1. ANY DAMAGE OR LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT. 2. PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OF NEGLIGENT OPERATION OF THE USER. 3. UNAUTHORIZED DISASSEMBLY, REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER. 4. INCONVIENIENCE OR ANY LOSE ARISIING WHEN IMAGES ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT. 5. ANY PROBLEM, CONSEQUENTIAL INCONVEINIENCE OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY. TRADEMARKS AND REGISTERED TRADEMARKS • MICROSOFT, WINDOWS, WINDOWS XP, WINDOWS 7, WINDOWS VISTA, WINDOWS EXPLORER ARE REGISTERED TRADEMARKS OF MICROSOFT CORPORATION IN THE U.S. AND/OR OTHER COUNTRIES • OTHER COMPANY NAMES AND PRODUCT NAMES APPEARING IN THIS DOCUMENT ARE REGISTERED TRADEMARKS OR TRADEMARKS OF THE COMPANY CONCERNED. Proprietary Information of PESA...
Page 5
FEATURES • Input support for HDMI Deep Color • Support for HDCP • Output support for 3G‐SDI formats(SMPTE 425M, Level A): 1080p @50/59.94/60Hz (4:2:2) • Output support for high‐definition (HD‐SDI) formats: 1080i @50/59.94/60Hz, 720p @50/59.94/60Hz • Output support for standard‐definition (SD‐SDI) formats: NTSC @59.94Hz, PAL @50Hz • Bit Rates for 2.97 Gbps, 2.967Gbps, 1.485 Gbps, 1.4835 Gbps, 270 Mbps • Auto 3G/HD/SD‐SDI detection • Easy installation with wall mounting design • Supports up to 8 channels of audio, 7.1 or 5.1 optional • Low jitter • Re‐clocked outputs for looping SD/HD/3G SDI signals Part number Description PRO‐HDMI2HD Conversion module to convert HDMI to SD‐SDI, HD‐SDI, and 3G‐SDI Proprietary Information of PESA...
PUB NO. 81905907090, Rev A 09/1/2012 PRO-HDMI2HD Chapter 1 BOUT YOUR PRODUCT 1.1 D ESCRIPTION PESA’s PRO‐HDMI2HD is a throw‐down style converter module allowing HDMI in 480p, 720p, or 1080p to SD‐SDI, HD‐SDI, or 3G‐SDI video signals to be viewed or recorded to a professional broadcast device supporting SMPTE 259, 292, or 424. The supplied power brick accepts a primary power input of 100‐ 240V, 50/60Hz, and supplies a +5V DC output. Power consumption is less than 3 watts. Each PRO‐HDMI2HD module sends output signals through a standard 75 Ohm BNC connection. Destination devices can be located up to 300m (1000ft) for SD‐SDI, up to 150m (500ft) for HD‐SDI, and 90m (300ft) for 3G‐SDI. The compact package comes with two mounting tabs for easy attachment to wall or under‐the‐table locations. FIGURE 1‐1: PESA PRO‐HDMI2HD Module 1.2 C ONNECTING NPUTS Each PRO‐HDMI2HD supports one HDMI input from a DVD player or computer. The input allows for an HDMI Type A connector (19 pin). FIGURE 1‐2 : PESA PRO‐HDMI2HD Input Connections in HDMI Type‐A Style Proprietary Information of PESA...
SD/HD/3G C ONVERTER ODULE PUB NO. 81905907090, Rev A 09/1/2012 1.3 C ONNECTING UTPUTS FOR FORMATS Each PRO‐HDMI2HD allows one 75 Ohm input supporting SD/HD/3G inputs. Devices can be connected up to 300m (SD‐SDI), 150m (HD‐SDI), and 90m (3G‐SDI). FIGURE 1‐3 : PESA PRO‐HDMI2HD Allows up to Two Re‐clocked Outputs for SMPTE 259, 292, 424 1.4 C PRO‐HDMI2HD ONNECTING POWER TO THE Connect the supplied power pack to the +5VDC connection on the module. Once power is applied, the RED power led should be lit. Once a signal has been detected, the GREEN led will be lit. Hand tighten the screw‐lock to get a snug connection. DO NOT OVER TIGHTEN. FIGURE 1‐4: PESA PRO‐HDMI2HD Power Supply Connection Proprietary Information of PESA...
HDMI SD/HD/3G C ONVERTER ODULE PUB NO. 81905907090, Rev A 09/1/2012 Installing your PRO-HDMI2HD Chapter 2 With all input and output devices and power connected, the following diagram provides a typical full detail of module installation. There are not software, but a two pin dip switch is included for special EDID settings. FIGURE 2‐1: PESA PRO‐HDMI2HD Full Connection Detail 2.1 S UPPORTED ESOLUTIONS 3G‐SDI INPUTS 1080p@ 50 / 59.94 / 60Hz SMPTE 424 / 425 (4:2:2) HD‐SDI INPUTS 720p @ 50Hz SMPTE 296 ‐3 720p @ 59.94 / 60Hz SMPTE 296 ‐1, ‐2 1080i @ 25Hz SMPTE 274 ‐6 1080i @ 29.97 / 30Hz SMPTE 274 ‐4, ‐5 1080p @ 23.98 / 24Hz ...
Defining the types of signals and connection styles FIGURE 2‐2: PESA PRO‐HDMI2HD Cable Connections and Maximum Lengths 2.3 DIP SWITCH SETTINGS – SETTING DIP SWITCH SETTING FOR AUDIO AND EDID LEARNING Each PRO‐HDMI2HD comes with a two pin dip switch allowing special EDID settings for specific audio support and EDID learning. FIGURE 2‐3: EDID Switch Settings EDID Learning Sequence • Set PIN #1 and PIN #2 DIP Switch to ON/ON • Connect an HDMI device to the HDMI port • Power on the PRO‐HDMI2HD module • The RED led light will illuminate indicating the EDID learning process is complete • Connect SD/HD/3G coax cables to the output sources • NOTE: DO NOT CHANGE SWITCH SETTINGS. OTHERWISE EDID INFORMATION WILL BE LOST. Proprietary Information of PESA...
Please consult our Customer Service Department before installing any parts not purchased from PESA. 3.5 F ACTORY ERVICE Before returning any equipment to PESA for service or repair, please contact our Customer Service Department for an RMA number. Proprietary Information of PESA...
[HD] 720p50/59.94/60 [HD] 1080i 50/59.94/60 [HD] 1080p24/30 [SD] NTSC @59.94 and PAL @ 50Hz Reclocking [3G‐SDI] up to 90m (300ft) [HD‐SDI] up to 150m (500ft) [SD‐SDI] up to 300m (1000ft) Audio Support Yes, embedded INPUTS (HDMI) Number of Outputs Connector Type HDMI, Type A (19 pin female) Standards HDMI 1.4 Cable connection distance ENVIRONMENTAL Housing Dimensions 79mm x 84mm x 27mm 3.1 x 3.3 x 1.2 inches Weight 250g (8.8 oz) Operational Temperature 0‐40 degree C Operational Humidity 20‐90% RH (non‐condensation) Power Connection +5VDC ( inter‐locking power plug) Power Consumption 3W (max) AC Power Brick 100‐240VAC, 50/60Hz Proprietary Information of PESA...
Page 13
HDMI SD/HD/3G C ONVERTER ODULE PUB NO. 81905907090, Rev A 09/1/2012 Warranty Chapter 5 PESA Switching Systems, Inc., (PESA) warrants this equipment against defective workmanship or materials for a period of one (1) year from date of shipment. The sole warranty responsibility of PESA, shall be to replace or repair product proved to be defective. During the warranty period, defective parts will be replaced at no charge. Labor to repair or replace defective parts covered under the warranty will be performed at no charge at PESA. This warranty covers only products manufactured by PESA, and the components used in their manufacture. The warranty on assembled products sold by PESA., but manufactured by others shall be that of the original manufacturer. This warranty does not include shipping damage or damage caused by abuse, neglect, tampering by unauthorized personnel, damage inadvertently caused by the user, preventative maintenance, or any equipment or part thereof whose serial number has been removed or defaced. Neither the seller nor the manufacturer shall be liable for any injury, loss or damage, direct or consequential, arising out of the inability to use the product. Before using, user shall determine the suitability of the product for the intended use, and user assumes all risk and liability whatsoever in connection therewith. This warranty is effective only at the PESA factory in Huntsville, Alabama, USA. If possible, retain the original packing material for use in the unlikely event that your equipment must be returned to the PESA factory. When shipping your equipment, the shipping charges must be prepaid. The repaired unit will be returned to you, freight prepaid. This warranty is exclusive and in lieu of all other warranties, whether expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose. Proprietary Information of PESA...
Need help?
Do you have a question about the PRO-HDMI2HD and is the answer not in the manual?
Questions and answers