Shutter hardware vario-louvre fittings louvre end piece drilled in (8 pages)
Summary of Contents for Maco HAUTAU HS Comfort Drive
Page 1
HS Comfort Drive LIFT AND SLIDE FITTINGS/WINDOW AUTOMATION INSTALLATION INSTRUCTIONS Indoor operation with control button, HS Comfort Drive, 24 V DC wood/wood-aluminium/PVC, Scheme A/C Used exclusively for specialist companies. Copy of the original instructions...
Contents Important safety instructions Warranty Disposal Other applicable documents Explanation of terms Intended use Features Device overview Installing the button box Circuit diagram Operation In the case of initial operation with control button (Full Init = factory reset) Normal mode Calibration run (Home Init = software reset) Activating Full Init and Home Init Feedback signals...
Important safety instructions It is important to observe the following instructions to ensure safety for everyone. Incorrect installation can cause serious injuries. Manufacturer’s declaration/technical standard The accessories contained in this document have been tested and manufactured in line with the applicable European directives.
Other applicable documents This document comprises additional instructions for the following manuals: - Installation instructions for HS Comfort Drive, 24 V DC, wood/wood-aluminium, concealed, Scheme A - Installation instructions for HS Comfort Drive, 24 V DC, wood/wood-aluminium, concealed, Scheme C - Installation instructions for HS Comfort Drive, 24 V DC, wood/wood-aluminium/PVC, surface-mounted, Scheme A - Installation instructions for HS Comfort Drive, 24 V DC, wood/wood-aluminium/PVC, surface-mounted, Scheme C The aforementioned documents apply to this manual.
Device overview Power supply and connection to the HS Comfort Drive circuit board, Terminal X4 Connection for buttons Buzzer for feedback signals (in the housing) Connection cable (length: 10 m) Installing the button box WARNING Disconnect the power supply to the actua- tor while carrying out connection work.
Control keypad/ control button Control button (provided by customer) Black Brown Button box Circuit board for HS Comfort Drive Control button actuator module Cabling (supplied connection Shown example: by customer) HS Comfort Drive, concealed; relevant for surface-mounted version In certain cases, Bridge 1-9 must be removed (see manual for Scheme A).
Operation The control keypad remembers the sash’s last movement. Randomly pressing the button in quick succession will mean the commands are ignored to protect the actuator system. HS/S Comfort Drive in automatic mode: pressing the button continuously for about 20 seconds will reset the software (Home Init) while pressing the button continuously for about 30 seconds will reset to factory settings (Full Init).
Complete, automatic initialisation* Operating mode switch Appearance may vary *) You can use the control button to interrupt the process at any time **) Reduced stop range of 10 mm instead of 130 mm before mech. end position...
Operating mode switch *) Default setting for operating mode switch on delivery (‘0’) In the HAUTAU/MACO version: If the operating mode switch is set to ‘3’, the sash stops about 10 mm before the mechanical end position. WARNING: This setting poses a risk of fingers be- ing crushed in the central stile section.
Feedback Mode Type of initialisation Action signal Automatic mode Software reset (Home Init) Press button for about 20 sec. (DIP switch 4 at ON) Factory reset (Full Init) Press button for about 30 sec. Audible signal Dead man mode Double-click + press button for Software reset (Home Init) (see below) (DIP switch 4 to OFF)
Technical specifications Operational power supply Supply voltage 24 V DC (–10%/+30%) Ripple ≤ 20% in relation to the nominal voltage Current draw max. about 14 mA Standby about 4 mA Wattage max. about 0.4 W Standby about 100 mW Material and mechanical properties Dimensions: w x h x d (mm) 50 x 47 x 28 Plastic housing...
Page 14
Tel.: +49 5724 3930 Email: info@hautau.de www.hautau.de/en/ This printed document is continually updated. Created: 08/2023 – amended: 06/2024 Order no. 759973 You will find the latest version at https://www.maco.eu/assets/759973 or scan the QR code. All rights reserved. Subject to change.
Need help?
Do you have a question about the HAUTAU HS Comfort Drive and is the answer not in the manual?
Questions and answers