Advertisement
Advertisement
Table of Contents
Related Manuals for Milwaukee M12FDGS-422B
Summary of Contents for Milwaukee M12FDGS-422B
- Page 1 M12 FDGS Original instructions...
- Page 2 M12 FDGS Original instructions Alkuperäiset ohjeet Algupärane kasutusjuhend Originalbetriebsanleitung Πρωτότυπο οδηγιών χρήσης Оригинальное руководство Notice originale Orijinal işletme talimatı по эксплуатации Istruzioni originali Původním návodem k používání Оригинално ръководство за Manual original Pôvodný návod na použitie експлоатация Instrucţiuni de folosire originale Manual original Instrukcją...
- Page 3 Technical Data,Safety Instructions, Speci ed Conditions of Use, Declaration of Conformity, Batteries, Maintenance, Symbols Please read and save these instructions!
- Page 4 = min. 10 mm ø 6 mm...
- Page 5 ø 8 mm...
- Page 7 n ≤ n max. MODE n (min 0-10 000 0-15 000 0-21 000 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 2 2 2 2 2 2 2 2 2...
- Page 8 Start 2 sec...
- Page 9 Load-dependent motor protection: If the motor is overloaded, the overload protection will trip. To continue working, switch the machine o and then on again. If the battery becomes too hot, the fuel gauge lights will ash in an alternating pattern and the tool will not run. Allow the battery to cool down.
-
Page 11: Technical Data
TECHNICAL DATA M12 FDGS Fuel Straight Die Grinder Production code 4748 00 02..000001-999999 Battery voltage 12 V Rated speed 1 / 2 / 3 0-10000 / 0-15000 / 0-21000 min Collet diameter 6,0 mm Collet diameter 8,0 mm Abrasive grinding body diameter max. 50 mm Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah...6,0 Ah) 0,7... - Page 12 bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time. h) Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments.
- Page 13 away from the operator, depending on direction of the wheel’s g) Support panels or any oversized workpiece to minimize the movement at the point of pinching. Abrasive wheels may also break risk of wheel pinching and kickback. Large workpieces tend to sag under these conditions.
-
Page 14: Transporting Lithium Batteries
Temperatures in excess of 50°C (122°F) reduce the performance of components need to be replaced which have not been described, the battery pack. Avoid extended exposure to heat or sunshine (risk please contact one of our Milwaukee service agents (see our list of of overheating). guarantee/service addresses). -
Page 15: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY SYMBOLS We declare under our sole responsibility that the product described under “Technical Data” ful lls all the relevant provisions of the CAUTION! WARNING! DANGER! directives 2011/65/EU (RoHS) Please read the instructions carefully before starting the 2006/42/EC machine. - Page 16 Copyright 2020 Techtronic Industries GmbH Techtronic Industries (UK) Ltd Max-Eyth-Straße 10 Fieldhouse Lane 71364 Winnenden Marlow Bucks SL7 1HZ Germany +49 (0) 7195-12-0 (11.20) www.milwaukeetool.eu 4100 4255 02...
Need help?
Do you have a question about the M12FDGS-422B and is the answer not in the manual?
Questions and answers