Page 4
INTRODUCTION IMPORTANT SAFETY INSTRUCTION ................INTRODUCTION TO REFRIGERANTS R32(Only for R32 Model)........ELECTRICAL REQUIREMENTS ................... PACKING LIST ......................INSTALLATION&ASSEMBLY INSTRUCTIONS .............. THROUGH-THE-WALL INSTALLATION INSTRUCTIONS..........INSTALLATION & ASSEMBLY INSTRUCTIONS.............. USING YOUR AIR CONDITIONER ................OPERATING YOUR AIR CONDITIONER ................ CARE AND CLEANING ....................TROUBLESHOOTING ....................
Page 6
INTRODUCTION TO REFRIGERANTS R32(Only for R32 Model) The refrigerants used for air conditioners are environmentally friendly hydrocarbons R32. This kind of erant is combustible and odorless. Moreover, it can burn and explode under certain condition. However, there will be no risk of burning and explosion if you comply with the following table to install your air conditioner in a room with an appropriate area and use it correctly.
Page 8
3/8" Short Screws 1/2" Length Screws 3/4" Long Screws 5/8" Big Flat Head Bolt and Locknut Sill Angel Bracket 1/2" Small Flat Head Bolt and Locknut Chassis Lock (Only for E-star model) Support Bracket(with R and L remark) Battery...
Page 9
ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER’ S MANUAL ARE THE PRESENTATION OF THE MANUFACTURE. PLEASE READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY. Window preparation For 6K/8K-Cooling 1. This air conditioner is designed to be installed In a standard double-hung window with a window width.
Page 10
REMOVE FRONT PANEL AND CHASSIS 1. Pull down the front panel and remove the filter. 5. Remove the control panel screw and WI-FI module screw (if available) from the front panel. 2. Lift the front panel upwards to remove and place to the side.
Page 11
Top Rail Assembly Top Foam Top Rail 1. Place the cabinet on a hard flat surface. 2. Remove top rail from the top form of the packaging material as shown in FIG. A. 3. Align the hole in the top rail with those on the top of the unit as shown in FIG.
Page 12
Accordion Panel and cabinet Assembly 1.Hold the Accordion Panel in one hand and gently 4.Use two or more people, place the air conditioner pull the center to free the open end. into the window opening so the bottom of the air conditioner frame is against the window sill.
Page 13
1.Hold each support bracket flush against the outside of the window sill. Tighten each bracket to the bottom of the cabinet as shown. Mark the brackets at top lever of the Bolt and Support bracket window sill and then remove. Locknut Sill angle bracket 4.
Page 14
5.Extend the side accordion panels out against 7.To secure lower sash in place, attach right angle the window frame as shown. sash lock with 3/4” screws as shown. Sash lock 6.Drive 1/2” locking screws through frame holes, 8.Cut foam seal and insert in the space between and drive one 3/4”...
Page 15
THROUGH-THE-WALL INSTALLATION INSTRUCTIONS - OPTIONAL The case may be installed through-the-walll as optional. NOTE: The allowed maximum wall thickness is less than Read completely, then follow step-by-step. 8 9/10”. Otherwise, the wall will block the air inlet of NOTE: Obtain all materials locally for mounting the air outdoor side, it will effect the normally operation of unit.
INSTALLATION & ASSEMBLY INSTRUCTIONS Important Considerations Before installing the appliance, you must read the manual carefully to get the safety information and notes. Unit refrigerant charge amount: refer to unit name plate marking. A leak test must be done after the installation is completed. It is a must to do the safety inspection before maintaining or repairing an air conditioner using combustible refrigerant in order to ensure that the fire risk is reduced to minimum.
Page 17
Cool Mode: The cooling function allows the air conditioner to cool the room and at the same time reduces air humidity . Press the MODE button to activate the cooling function. To optimi z e the function of the air conditioner, adjust the For Cooling model temperature and the speed by pressing the button indicated.
Page 18
6. ECO Button: When the unit is in ECO mode, the Directional Louvers: To direct the airflow, use the light will turn on. In ECO mode, the unit will turn-off horizontal wheel to control the horizontal direction once the room is cooled to the user set temperature. and the air deflector to control the vertical The unit will turn back on when the room temperat- direction.
Page 19
5. Timer: Use these buttons on the control panel and remote to set the Timer. Timer Off: The timed stop is programmed by pressing TIMER button. Set the rest time by pressing the button until the rest time displayed is to your demand then press TIMER button again.
Page 24
CrosleyCare servicer. For one year from your original date of purchase, Crosley will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions.
Need help?
Do you have a question about the CATHE12A2 and is the answer not in the manual?
Questions and answers