Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for OBZ OV-11R
Summary of Contents for OBZ OV-11R
- Page 1 1D Wireless Laser Barcode Scanner User Manual Model: OV-11R...
- Page 2 Contents...
-
Page 3: Factory Default
Factory Default Power Off Note: Scan this barcode, scanner will make a long beep and power off. Technical Parameter Barcode Scanner Date Item Parameter Type of Light Source 650nm(Safe visible laser diode) Decoding Accuracy ≥5mil Decoding Ability Continue the table below... - Page 4 Continue to the table System Compatibility Windows XP/7/8/10, Linux, Android Lithium Battery 550mAh Cable Length 1.2M Material ABS+PC Current 85mA Voltage DC5V±1% Withstands multiple 3 meters free fall Shock Resistance Operating Temperature -20℃~60℃ Storage Temperature -40℃~70℃ Operating Humidity 5%-95% RH without condensation 4mil(0.1mm) Resolution Scan Type...
- Page 5 2.4G USB Receiver Pairing Instruction Step 1: Scan “Factory Default” Factory Default Pairing Barcode The Correct Usage of Barcode Scanner 1. Make sure barcode scanner, cable/USB receiver, host device connect properly. 2. Press trigger button and the red laser line appears, and remove the laser line to cover barcodes completely, adjust barcode scanner's distance and angle to figure out best reading status.
-
Page 6: Keyboard Language
Correct reading Correct reading Incorrect reading Incorrect reading Keyboard Language USA(Default) French German Italy Spanish... -
Page 7: Buzzer Setting
Japanese Buzzer Setting ON(Default) High Keyboard Caps Lock Control None(Default) Capitalize Case Swap Lower Case... -
Page 8: Transmission Speed
Transmission Speed No Delay Delay 3ms Delay 5ms Scan Mode Manual(default) Continuous Auto-sensing Auto-sense Mode Enable Disable... - Page 9 Data Saving Mode Automatic Storage(Default) Instant Upload Mode Inventory Mode Remark: 1) Automatic Storage Mode (default): The data will be uploaded to host device immediately after scan if the scanner in range, the data will saved in the memory chip if the scanner out of range which will heared 2 alarm beeps, press the scanner trigger to upload the saved data after back to range, and the original data in the memory ship will be cleared.
-
Page 10: End Character
Upload one data and delete Upload one data But not delete Display all data Delete all data End Character CR(Default) CR&LF None Prefix Setting Add Prefix Prefix... - Page 11 Eg: Add Prefix "A” Step 1: Scan above code to enter into "Add Prefix"; Step 2: Scan above code to add "Prefix"; Step 3: Refer to "Data Codes"(Page14-25), find the character "A" in the "Data Codes" and then scan the "A" barcode. Eg: Add Suffix "a”...
- Page 12 EAN-13 Enable(default) Disable UPCA Enable(default) Disable UPC-E Enable(default) Disable Code 39 Enable(default) Disable Interleaved 2 of 5 Enable(default) Disable...
- Page 13 Industrial 2 of 5 Enable(default) Disable Codabar Enable(default) Disable Barcode Conversion EAN 13 Converts ISBN Enable Disable(default) EAN 13 Converts ISSN Enable Disable(default) UPCA Converts EAN13 Enable Disable(default)
- Page 14 Additional Code 2-bit Additional Code for EAN-8 Enable Disable(default) 5-bit Additional Code for EAN-8 Enable Disable(default) Data Codes Appendix 1:...
- Page 20 Backspace...
- Page 22 “ & ‘...
- Page 23 < >...
- Page 26 INSERT HOME Page up Delete Page down Right arrow Left arrow Up arrow Down arrow...
- Page 27 For more setting, welcome to contact us for tech support. Service support: support@obzshop.com THANK YOU FOR CHOOSING OBZ.
Need help?
Do you have a question about the OV-11R and is the answer not in the manual?
Questions and answers