Warning: The use of alcohol, drugs, or other medication can greatly increase the risk of fatal hyperthermia. SAVE THESE INSTRUCTIONS Kohler Co., Kohler, WI U.S.A. 114170-2-...
Follow the sections that pertain Kohler Co. reserves the right to make changes in to your particular installation. This will help you avoid product characteristics, packaging, or availability at any costly mistakes.
NOTICE: Follow all local plumbing and electrical performance and safe operation of the whirlpool. codes. Kohler Co. shall not be liable under its warranty or otherwise for personal injury or damage caused by any such unauthorized modification. 4. PRODUCT REQUIREMENTS A.
Old Bath Floor Protection Boards B. SUBFLOOR PREPARATION Check the flooring under the bath, and make repairs as needed. Make sure the subfloor is level. Kohler Co., Kohler, WI U.S.A. 114170-2-...
Sunken Installation: Refer to Roughing-In notes beginning on Page 4 for cut-out details. Make sure the whirlpool is supported by the supporting feet on the bottom of the whirlpool. Do not hang the whirlpool by the rim. Kohler Co., Kohler, WI U.S.A. 114170-2-...
Option For Sunken Installation: Set the bath into the sunken installation. Make sure the unit is level and resting on all support feet. Insert the drain tailpiece into the trap. Apply a bead of silicone sealant under the rim of the unit. Kohler Co., Kohler, WI U.S.A. 114170-2-...
Rim and Framing B. PUMP BANDING STRAP CUT Shipping Bracket (leave attached NOTICE: This step is necessary to make your to bath) Kohler whirlpool operate more quietly. Pump Banding Straps Use tin snips to cut the two banding straps. These banding straps...
Jets grounding adapter. Auxiliary Control Your Kohler whirlpool bath is equipped with a cord and plug. All wiring of the pump and control has been completed at the factory. A licensed electrician must Pump install a GFCI-protected, 120 V, 20 A, grounded outlet.
Install the faucet handles and spout according to the manufacturer’s instructions. Seal around the plumbing fittings. B. INSTALL WHIRLPOOL TRIM KIT Refer to the installation instructions packed with the trim kit when installing the jet or suction trim. Kohler Co., Kohler, WI U.S.A. 114170-2-...
Jet Trim Ensure that the pillow with cover is properly installed before you test the neck jets. Water temperature in the bath should not exceed 104_F (40_C). Kohler Co., Kohler, WI U.S.A. 114170-2-...
Insert the Flexjet into the housing, and lightly push and rotate the Flexjet until it snaps into position. Do not force the Flexjet. O-Ring (Must Be NOTE: When installed correctly, the Flexjet should turn Lubricated) smoothly both clockwise and counterclockwise. Kohler Co., Kohler, WI U.S.A. 114170-2-...
Page 16
B. TROUBLESHOOT WHIRLPOOL SYSTEM This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or a qualified electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor. SYMPTOMS PROBABLE CAUSES RECOMMENDED ACTION 1.
Page 17
C. TROUBLESHOOT WHIRLPOOL SYSTEM – NECK JETS This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or a qualified electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor. 1. Neck jets do not A.
Page 18
Kohler Co., Kohler, WI U.S.A. 114170-2-...
Page 19
Kohler Co., Kohler, WI U.S.A. 114170-2-...
Need help?
Do you have a question about the Vintage K-702-N and is the answer not in the manual?
Questions and answers