Download Print this page
Philips CertaFlux Quick Installation Manual
Philips CertaFlux Quick Installation Manual

Philips CertaFlux Quick Installation Manual

Ledflex system

Advertisement

Quick Links

Please read this manual carefully before using the product
使用本产品前,请先仔细阅读本手册
The manufacturer will not be held responsible for improper usage or
modifications of the product,
所有不当使用或自行更改产品结构而导致损坏,生产商不负任何责任。
Connector must in accordance with IEC60838-2-2.
连接器必须符合IEC60838-2-2标准。
Indoor use only.
仅限室内使用。
Operation instruction 使用操作说明:
Please take anti-static measure during installation and maintenance.
安装和维护时,请做好防静电措施。
In case of operation failure, please switch off the power and contact your
nearest Philips dealer.
如发现异常或操作有任何问题,请务必先切断电源,然后与飞利浦经销商联系。
Maintenance 保养方法:
In order to ensure optimum performance, please clean the product
regularly (recommended twice a year). When cleaning the product,
please use soft dry cottoncloth only.
为了保持灯带明亮效果,请定期(半年一次)进行清洁。
灯带不洁处需擦拭时,请用柔软干燥的布料擦拭。
Do not use chemical solvents to clean the lighting strip, it might damage
the surface.
请不要用香蕉水等挥发性物质擦拭灯带表面,请不要对灯具喷洒
任何化学药剂,否则灯具可能会变色或损坏。
Attention 注意:
Please shut off the power supply before mountIng and maintaining lighting
strip!
安装和维护灯带时请务必先关闭电源!
The lighting strip shall be installed by a qualified electrician and wired in
accordance with the latest IEE electrical regulations or the national
requirements.
灯带应由有资格的电工安装,接线要符合IEE电气标准或国家标准。
The lighting strip shall not be covered with thermal insulation or similar
material under any circumstance,
灯带不允许被隔热或类似材料覆盖。

Advertisement

loading
Need help?

Need help?

Do you have a question about the CertaFlux and is the answer not in the manual?

Questions and answers

Summary of Contents for Philips CertaFlux

  • Page 1 In case of operation failure, please switch off the power and contact your The lighting strip shall be installed by a qualified electrician and wired in nearest Philips dealer. accordance with the latest IEE electrical regulations or the national 如发现异常或操作有任何问题,请务必先切断电源,然后与飞利浦经销商联系。...
  • Page 2 ≥30mm ≥30mm 弯曲半径应不小于30mm The bending radius shall not be less than 30mm 禁止旋转扭曲灯带 Do not twist the ribbon 灯带安装方式/LEDFlex Installation 撕开胶膜 Remove release paper 清洁表面 Clean the surface 粘贴灯带 Stick on...
  • Page 3 RGBW 24V+ 24V+ 24V+ RGBTW WiZ Pro TW Bridge Box I 12-24V WiZ Pro RGBTW Bridge Box I 12-24V 12nc:929002499509 12nc:929002613309 Compatible driver list please refer to Design-in Guide 兼容驱动程序列表请参考设计指南 https://www.lighting.philips.com.sg/oem-asia/support/technical-downloads Bridge Box needs to be purchased separately Bridge Box需要单独购买...
  • Page 4 连接器安装方式/Connector Installation 连接器要单独购买 保证焊盘表面平整没有锡焊 Connector needs to be purchased separately. No tin on solder pad 整齐切割灯带 Cut the light strip neatly 保持焊盘完整 Keep the whole pad remain 揭开背胶 Remove release paper and tape PCB-wire PCB-PCB...
  • Page 5 连接器拆解方式/Connector Disassembly 分解灯带 Separate 撬开连接器 连接器不可重复使用 Pry off the connector Connectors are not reusable 焊线/Wire Soldering 整齐切割灯带 Cut the light strip neatly 连接线裸线锡焊预处理 Solder pretreatment of bare wire of connecting wire 撕开胶膜 焊接灯带 Remove release paper Soldering...
  • Page 6 热学设计/Thermal design 散热/ Cooling 灯带的电和热功率相对较小。一个良好的热接触通过3M™胶带到散热器是一个好的灯具的 必要条件。为了使接触良好,在安装过程中应施加一定的压力。当对灯带施加压力时,注 意不要对电子元件施加力,以免损坏电子元件,避免超过2kV的静电。散热器表面必须光滑 无毛刺,以获得最佳的接触。散热器不应在密闭空间内使用,应该与周围空气接触,以获 得最佳的热量传递到周围环境。 The LEDFlex modules have a relatively small footprint in relation to their electrical and thermal power. A good thermal contact via the 3M™ tape to an adequate heat sink, is a necessity for a good luminaire. To make good contact a certain pressure should be applied during installation.
  • Page 7 CertaFlux LEDFlex 5m 1200lm/m 9xx C5 G2 self cooling self cooling self cooling CertaFlux LEDFlex 5m 1500lm/m 9xx C5 G2 CertaFlux LEDFlex 5m 2000lm/m 9xx C5 G2 self cooling 3) LEDFlex灯带的自散热定义和灯具类型。 4) 非自散热示例 Orientation and luminaire type of LEDFlex for selfcooling Example non-selfcooling heat dissipation.
  • Page 8 05/29/2024...