Download Print this page
Sharp BP-50C26 Installation Manual
Sharp BP-50C26 Installation Manual

Sharp BP-50C26 Installation Manual

Digital full color multifunctional system
Hide thumbs Also See for BP-50C26:

Advertisement

Quick Links

Manual de instalare
BP-50C26/50C31/50C36/50C45BP-
50C55/50C65/55C26BP-60C31/60C36/60C45BP-
70C31/70C36/70C45BP-70C55/70C65
Considerente generale privind instalarea echipamentelor de printing:
- Manipularea echipamentelor se face respectand procedurile de
transport si punere in locatie tinand cont de gabaritul echipamentului si
a spatiului destinat acestuia
- Respectarea normelor privind conectarea la reteaua electrica, folosirea
de prize cu impamantare este obligatorie
- Fixarea corecta a echipamentului pe standul acestuia
- Verificarea cu atentie si eliberarea tuturor blocajelor folosite la transport
(inclusiv cel pentru scanner, unitati developare, cilindrii, etc)
- Montarea corecta a tonerelor in echipament dupa agitarea prealabila
(atentie unele echipamente nu au tonerul in echipament ci separat)
- Manipularea cu atentie a cilindrilor evitand pe cat posibil expunerea
prelungita a acestora la lumina.
- Manipularea cu atentie a cuptorului tinand cont de temperatura
acestuia
- Temperatura ambientală unde se folosesc aparatele şi echipamentele
trebuie să fie între 18 şi 30 grade celsius, cu grad minim de praf şi
umiditate.
pentru
multifunctionale
SHARP

Advertisement

loading
Need help?

Need help?

Do you have a question about the BP-50C26 and is the answer not in the manual?

Questions and answers

Summary of Contents for Sharp BP-50C26

  • Page 1 Manual de instalare pentru multifunctionale SHARP BP-50C26/50C31/50C36/50C45BP- 50C55/50C65/55C26BP-60C31/60C36/60C45BP- 70C31/70C36/70C45BP-70C55/70C65 Considerente generale privind instalarea echipamentelor de printing: - Manipularea echipamentelor se face respectand procedurile de transport si punere in locatie tinand cont de gabaritul echipamentului si a spatiului destinat acestuia - Respectarea normelor privind conectarea la reteaua electrica, folosirea...
  • Page 2 INSTALLATION MANUAL CODE: 00ZBP70C45I3E DIGITAL FULL COLOR MULTIFUNCTIONAL SYSTEM BP-50C26/50C31/50C36/50C45 BP-50C55/50C65/55C26 BP-60C31/60C36/60C45 BP-70C31/70C36/70C45 BP-70C55/70C65 MODEL CONTENTS Transit, Installation (Using) Environment, Note CONFIGURATION [1] MAIN UNIT ....... . 1-1 [2] BP-DE12/DE13/DE14 (STAND/550/2x550/3x550 SHEET PAPER DRAWER) .
  • Page 3 BP-70C45 CONFIGURATION 1. System diagram BP-70C45 CONFIGURATION – iv...
  • Page 4 2. Option list BP-50C26 BP-70C31 BP-50C31 BP-70C36 BP-60C31 BP-50C36 Model name Description BP-70C45 BP-60C36 BP-55C26 Remarks BP-50C45 BP-70C55 BP-60C45 BP-50C55 BP-70C65 BP-50C65 Document REVERSING SINGLE PASS FEEDER Feed System DUPLEX SINGLE PASS FEEDER Paper Feed BP-DE12 STAND/550 SHEET PAPER DRAWER...
  • Page 5 BP-70C45 [6] SIMULATION Service Manual Tap the Ver display section (10-key mode input mode screen) General and purpose The simulation mode has the following functions, to display the machine operating status, identify the trouble position and causes in an earlier stage and to efficiently setup and adjust the machine for improved serviceability.
  • Page 6 [1] MAIN UNIT BP-70C45 Remove F -add. Remove the vinyl bag of the main unit. Unpacking Cut the polypropylene bands. Pull out the grips. Remove the top case, cushioning materials, and case of the main unit. Lift the main unit slowly by 4 people, and put it gently to the flat and safety place.
  • Page 7 A. Fixing tape and protection material removal Push lock levers on both ends of waste toner box inward and pull up waste toner box. Remove tape from waste toner box. * Tape is used when moving the machine, so keep it as needed. Make sure that the lock lever has moved to the position indicated by the arrow.
  • Page 8 B. Packed items check Remove the protection material. Open the right door. Name Quantity Operation manual Protection sheet C. Lock release (1) Tray rotation plate lock release Pull out the tray. Turn the fixing material and remove it. Remove the caution label. Attach the removed fixing material to the position shown in the fig- ure for future use.
  • Page 9 Attache the protection sheet. (Packed item No.2) Mounting location of the toner cartridge of each color (2) Cleaning a. Cleaning of LSU's dust-proof glass Dust from the transfer belt or shutter or some other adjacent part may fall onto the LSU during transport or installation. Be sure to clean the D.
  • Page 10 Return the LSU cleaning rod to the front cover so that the felt MFP Automatically rebooted and enters the toner replenishment faces upward. Fit the boss, and fix it with three pawls. operation. Confirm that "Toner replenishment in progress" is displayed and wait until the display disappears (it takes 30 sec - 4min) This procedure is for checking the toner supply operation from the toner cartridge to the DV unit.
  • Page 11 Adjust the guide plates A and B by squeezing their lock levers and (4) Specifications setup sliding them to match the vertical and horizontal dimensions of the Use SIM26-6 to set the machines destination. paper to be loaded. The guide plates A and B are slidable. Slide each guide plate SIM No Content while squeezing its lock lever.
  • Page 12 Write down the displayed skew level. b. Copy color balance and density check (Meaning of the skew level value and the adjustment procedure) Method * If "OK" is displayed for all items of SKEW C, Make a copy of the gray test chart (UKOG-0162FCZZ) and a copy of M, and Y, there is no need to perform the adjustment.
  • Page 13 a. Color copy check items (Check to confirm the following:) There are 12 void areas. The color difference in gray balance between the F and the R sides is not so great. Registrations (one point for the main scanning, and one point for the sub scanning) are not shifted.
  • Page 14 b. Monochrome copy check items (Check to confirm the following:) There are 12 void areas. There are no white and black streaks. The resolution of 4.0 (5 points) can be seen. Solid density is not so light. The density difference between the F and the R sides is not so The black low-density gradation is copied slightly.
  • Page 15 c. Printer color balance/density check Select [FACTORY] target, and press [EXECUTE] key. Method When the color balance is customized by the manual color bal- ance adjustment (SIM46-21) according to the user's request, and Execute SIM64-5 to print the print test pattern. the color balance is registered with SIM63-7 as the service target, if the color balance is required to be adjusted, select the [SER- VICE] target.
  • Page 16 Select [FACTORY] target, and press [EXECUTE] key. e. Print/scan image off-center, lead edge position adjustment When the color balance is customized with the manual color bal- Before executing this adjustment, be sure to check the following ance adjustment (SIM67-25) according to the user's request and items.
  • Page 17 BP-70C45 [2] BP-DE12/DE13/DE14 (STAND/550/2x550/3x550 SHEET PAPER DRAWER) Unpacking To ensure safety, insert right adjuster until it is locked. Before installation, be sure to turn both the operation and main power switches off and disconnect the power plug from the power outlet. Make double sure that the data lamp on the operation panel does not light up or blink when performing installation.
  • Page 18 Attach the tray 1 and the tray 2. Place the main unit on the desk unit slowly by fitting the external lines. Check to insure that the positioning pin on the top of the desk unit is securely engaged in the positioning groove of the main unit.
  • Page 19 Adjustment D. Connector connection Remove the cover from the rear side of the machine. Before installation, be sure to turn both the operation and main power switches off and disconnect the power plug from the power outlet. Make double sure that the data lamp on the operation panel does not light up or blink when performing installation.
  • Page 20 Calculation and input procedures of adjustment values (Example) Lead edge void amount (1) Measure by visual inspection. Measurement result: 4.5mm (2) Calculate the shift amount. The target value is the specification value (center value) of 3mm. * For the F side void amount, the target is 2mm. [4 –...
  • Page 21 BP-70C45 [3] BP-DE15 (STAND/550&2100 SHEET PAPER DRAWER) Unpacking Turn each adjuster to fix the desk unit. If the connector is removed first, it may be damaged during the instal- lation procedures. Therefore, keep it packed while un-boxing. and unpack it only when connecting the connector to the machine. A.
  • Page 22 Remove the tray 1 and the tray 2. Take off the small cover of right and left sides of the main body rear. And fix them with the fixing screws (Packed item No.2). Return small covers. Raise the linkage plates on the right and left sides of the front side of the desk unit, and fix them with the fixing screws (Packed item C.
  • Page 23 D. Connector connection E. Turn ON the power of the main unit Remove the cover from the rear side of the machine. Connect the power plug of the machine to the power outlet, and turn ON the main power switch and the operation panel power switch.
  • Page 24 b. Tray 3 (A4/LT) c. Tray 4 (A4/LT/B5) Pull out the Tandem paper feed tray. Pull out the Tandem paper feed tray. Remove the Tandem tray regulation plate while pressing a hook. Remove the Tandem tray regulation plate while pressing a hook. Insert Adjust plate boss to the holes on the Tandem tray regula- Insert Adjust plate boss to the holes on the Tandem tray regula- tion plate for appropriate size.
  • Page 25 Lay B5 rear edge regulation plate to set for A4/LT size.Erect the regulation plate to set for B5 size. Push the Tandem paper feed tray. (3) Size setting Execute SIM26-2 "Size setting" with the key operations of the main unit. Calculation and input procedures of adjustment values The size selection menu of the large capacity desk is displayed on (Example) Lead edge void amount...
  • Page 26 BP-70C45 [4] BP-LC10 (LARGE CAPACITY TRAY) Installation Unpacking Before installation, be sure to turn both the operation and main power If the connector is removed first, it may be damaged during the instal- switches off and disconnect the power plug from the power outlet. lation procedures.
  • Page 27 B. Main unit and large capacity tray connection Attach the mounting plate upper (Packed item No.2) to the right side of main unit with the fixing screw A (Packed item No.4). When installing, put the rubber section ( ) of the mounting plate upper on the lower side.
  • Page 28 Temporarily fix the fixing screw B (Packed item No.5) midway. Fix the fixing screw, and attach the screw cap back to the main unit. Insert the temporarily fixed screw B into the key hole in the con- 10) While lifting the section marked with insert the connection unit nection unit and temporarily fix the connection unit.
  • Page 29 Check to insure that the height adjustment check rib of the large In the case of a shift to the right, press the front upper section and capacity tray and the axis line of the mounting plate upper fit the height adjustment check rib so that it is in the same line with mounted to the main unit are in the same line.
  • Page 30 D. Connector connection E. Paper size switch Remove the connector cover. Remove Rear cover. Do not use the connector cover removed. Remove fixing screw (4 pcs of blue screw) on upper and lower side of Side plate F and Side plate R. Connect the connector.
  • Page 31 Insert Size guide according to the engraved mark. Tighten upper and lower side using the fixing screws being removed (A4). (LT) (B5) Switching Rear edge plate Remove the blue screws fixing the upper and lower Rear edge plate respectively. BP-70C45 BP-LC10 (LARGE CAPACITY TRAY) 4 – 6...
  • Page 32 Attach Rear cover. F. Turn ON the power of the main unit Connect the power plug of the machine to the power outlet, and turn ON the main power switch and the operation panel power switch. G. Size setting Execute SIM26-2 "Size setting" with the key operations of the main Calculation and input procedures of adjustment values unit.
  • Page 33 (2) Mechanical adjustment Since the off-center adjustment is performed when shipping, there is basically no need to perform this adjustment. If the center is shifted, however, the simulation is normally used. If the shift is not removed, perform the following adjustment procedures. a.
  • Page 34 BP-70C45 [5] MX-LT10 (LONG PAPER FEEDING TRAY) Unpacking Hook the Long paper feeding tray to the guide of the machine. A. Packed items check Name Quantity Long paper feeding tray Insert the guide of the machine. Installation Do not insert the finger in the hook part of the tray. This tray can only be used for long paper feeding.
Save PDF