Advertisement
I
FRONT PANEL FACILITIES
OPERATION OF DECK [ WITH A REMOTE
I
CONTROL UNIT NOT DESIGNED FOR
h
DOUBLE DECKS (System remote control)
I
Selecting
DECK [
In order to operate DECK [ with the remote control unit, adjust the
unit as follows: With the power off, press and hold the stop (m) but-
ton of DECK l, and turn the power on. Continue to hold the stop (1)
button for approximately five seconds. DECK ] can now be operated
using the remote control unit, but DECK ]l cannot.
Switching
to DECK ][
To restore remote control operation to DECK 11,press the stop (m)
button of DECK II while DECK II is in stop mode. DECK 11can now
be operated
using the remote control unit. Remote control opera-
tion can be switched
back and forth between
decks by pressing
the stop button of the desired DECK while it is in stop mode,
NOTE:
ff a power failure or a sudden change in the power supply (caused by
lightning,
etc.) occurs,
the unit is reset to its original state. Only
DECK II can be ol_rated
by remote control
To restore operation to
either deck, repeat the above procedure
from the beginning.
FUNCTION
DISPLAY
(_)
DECK ! counter
indicator
Normally
the tape counter or time counter
is displayed
(see
page 11). It flashes for 4 seconds after the power cord is con-
nected to the power supply.
(_
CD.DECK
SYNCHRO
indicator
(CD SYNC)
This indicator
lights steadily
when the CD SYNC button
is
pressed and the operation starts.
(_
FLEX
Indicator
(Except
for
U.S.
model
of
CT-
W606DRI
This indicator lights when the FLEX button is pressed.
_)
DECK ]1 counter
indicator
Normally the tape counter or time counter is displayed
(see
page 11). It flashes for 4 seconds after the power cord is con-
nected to the power supply.
(_
DECK I] tape
transport
mode
indicators
See table entitled "TAPE TRANSPORTATION
MODE INDICA-
TORS" on this page.
(_
DECK
[I AUTO
BLE XD indicator
(Except
for U.S.
model
of CT-W606DR)
•
See page 13.
(_)
DOLBY
NR BIC indicator
(_
Level meter
Holds peak for about 1.3 seconds.
The "e" mark beside the 0 dB mark indicates the Dolby NR sys-
tem standard level.
(_)
Reverse
mode
indicator
(_
DECK ! tape transport
mode
indicators
See table entitled
"TAPE TRANSPORTATION
MODE INDICA-
TORS" on this page.
TAPE TRANSPORTATION
MODE INDICATORS
I
10
<RRB1176>
En
PI.AY
_1_ <
PI-AyREC
_I_
These indicators display the current tape transport
mode. The chart
below shows the meaning of each of these indicators. The indicators
for DECK ] and DECK [1 differ only in the location of the PLAY and
REC indicators (DECK l-left, DECK ll-right).
For both
DECK ] and ]1
_:ZZI:_
Flashing rapidly
Forward mode
Reverse mode
Stop
_1_
Playback
PI.Ay
_
._
play
,.*J,
,_lf.
Fast forward
"_ , ._,,._ "-,_ ,_
Fast reverse
_-_'_
_
_
_'DI_
,,\
g /..
,qJ,
Forward
_
....
music search
, , _
-
-
_ _ ,
Reverse
"
" " .....
_1_
41 - l=l.Ay
_ _:
music search
_"
,_,, "_ P_
.Y.(-
.....
-,,.-
DECK II only
E_ Flashing slowly
Forward mode
Reverse mode
Playback pause
PLAY
_
_
PLAy
Recording
IR_=C
_1_
_
RmC
Recording
standby
REC
_
_
RISC
muteRecording
_
I_
41_
Hide quick links:
Advertisement
