Advertisement
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2780ZJ-X/316L
Summary of Contents for HIKVISION DS-2780ZJ-X/316L
- Page 1 Explosion-Proof Terminal Box Installation Guide...
- Page 2 Terminal Box·Installation Guide Quick Start Guide © 2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
- Page 3 Terminal Box·Installation Guide YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION,...
- Page 4 Terminal Box·Installation Guide NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Regulatory Information Intended Use of the Terminal Box and the Supplied Cable Gland with Elastomeric Sealing Rings ATEX: II 2 G D Ex db IIC T6 Gb/Ex tb IIIC T80℃...
- Page 5 Terminal Box·Installation Guide 3. USE FASTENERS WITH YIELD STRESS ≥ 450MPa Nameplate WARNING: DO NOT OPEN WHEN EXPLOSIVE ATMOSPHERE IS PRESENT POTENTIAL ELECTROSTATIC CHARGING HAZARD – SEE INSTRUCTIONS WARNING: DO NOT OPEN WHEN EXPLOSIVE ATMOSPHERE IS PRESENT AFTER DE-ENERGIZING, DELAY 5 MINUTES BEFORE OPENING POTENTIAL ELECTROSTATIC CHARGING HAZARD...
- Page 6 Terminal Box·Installation Guide For model difference, see Section 1.2. WARNINGS: 1. Ambient Temperature: -40°C to +60°C for the terminal box and the cable gland with elastomeric sealing rings. 2. When assembly, operation and maintenance, the operator must follow the requirements of the IEC 60079-14: latest version Explosive atmosphere- Part 14: Electrical installation design, selection and erection, beside of the manufacturer ’s operation instruction or its National equivalent.
- Page 7 Terminal Box·Installation Guide ● Grounding: The both internal and external earthing shall be connected reliably. Ground wire cross-sectional area of not less than the phase connector cross-sectional area level, at least 4 mm ● All the electrical operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations of the nation and region.
- Page 8 Terminal Box·Installation Guide ● To prevent accumulation of electrostatic charge, only damp cloth can be used during the cleaning. ● While in delivery, the device shall be packed in its original packing, or packing of the same texture. ● Regular part replacement: a few parts of the equipment shall be replaced regularly according to their average enduring time.
-
Page 9: Table Of Contents
Terminal Box·Installation Guide Table of Contents 1 Introduction ................1 1.1 Overview ................1 1.2 Model Description ............... 1 2 Appearance ................3 3 Installation .................5 3.1 DS-2781 and DS-2783 Series Installation ......5 3.2 DS-2780 and DS-2782 Series Installation ......11 viii... -
Page 10: Introduction
Cable Gland Use Preinstalled DS-2781ZJ-X Use cable gland sealed DS-2781ZJ-X/316L Input: 110 to 240 VAC with setting compound DS-2783ZJ-X Output: 12 VDC (buy separately) DS-2780ZJ-X Use cable gland with DS-2780ZJ-X/316L elastomeric sealing rings Input/Output: 110 to 240 DS-2782ZJ-X (included in package) - Page 11 With /316L: stainless steel 316L Without /316L: stainless steel 304 Feature: explosion-proof Product type: accessory Product series Power adapter included: 1 and 3 NO power adapter: 0 and 2 Product type: terminal box Material: stainless steel Front-end product Hikvision product Model Explanation...
-
Page 12: Appearance
Terminal Box·Installation Guide 2 Appearance 96.8 Ø 182 4-Ø 8.5 Unit: mm Figure 2-1 Explosion-Proof Terminal Box Overview... - Page 13 Terminal Box·Installation Guide Figure 2-2 Elastomeric Sealing Rings Overview Table 2-1 Accessory Description Description Elastomeric sealing rings (DS-2780 and DS-2782 series included) M25×1.5 to G3/4 adapter (DS-2780 and DS-2782 series included)
-
Page 14: Installation
Terminal Box·Installation Guide 3 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment. - Page 15 Terminal Box·Installation Guide Steps: Drill four screw holes (Ø8 mm) according to the dimension of the terminal box (see Figure 2-1), and insert four M8 × 80 expansion bolts. 2. Secure the terminal box on mounting place. Spring Washer Flat Washer Figure 3-1 Secure Terminal box 3.
- Page 16 Terminal Box·Installation Guide Plug Gasket Sealing Ring Cover Safety Rope Figure 3-2 Disassemble Terminal Box (1) 1). Loosen the plugs at “Camera” end and its opposite end, and take out the gaskets and the sealing rings. Normally, two ends are enough for cable routing. The others are reserved for unexpected conditions.
- Page 17 Terminal Box·Installation Guide Figure 3-3 Disassemble Terminal Box (2) 4. Route cables and wiring. 1). Install the camera cable to cable gland (sealed with setting compound). Refer to installation guide of the cable gland for detailed steps. 2). Secure the cable gland together with the cable gland sealing ring (a component of cable gland) to the “Camera”...
- Page 18 Terminal Box·Installation Guide Figure 3-4 Install Camera Cable 3). Connect wires to corresponding terminals. 4). Install a RJ45 head to network cables and plug it to RJ45①. 5). Repeat above steps to route source cables through the opposite “Camera” end, connect wires, install a RJ45 head and plug it to RJ45②.
- Page 19 Terminal Box·Installation Guide To Camera RJ45① RJ45② To Source Figure 3-5 Wiring 5. Screw the cover back to terminal box.
-
Page 20: Ds-2780 And Ds-2782 Series Installation
Terminal Box·Installation Guide 1). Check to ensure the O-shape ring stays in terminal box. 2). Align the locating hole of the cover with the locating pin on box, and gently lower the cover back to the box. When lowering the cover, prevent the explosion suppression surfaces from bump or scratch. - Page 21 Terminal Box·Installation Guide Spring Washer Flat Washer Figure 3-7 Secure Terminal box 3. Disassemble the terminal box. Plug Gasket Sealing Ring Cover Safety Rope Figure 3-8 Disassemble Terminal Box (1)
- Page 22 Terminal Box·Installation Guide 1). Loosen the gland nuts at the “Camera” end and the opposite “Camera” end, and take out the gaskets and the sealing rings. Normally, two ends are enough for cable routing. The others are reserved for unexpected conditions. Keep the unused ends firmed sealed (torque 50 Nm).
- Page 23 Terminal Box·Installation Guide If camera is NOT protected by flexible conduit, follow these steps: 1). Thread the camera cable through supplied adapter, gasket, and supplied sealing ring. Select a suitable sealing ring according to the diameter of your cable. Several kinds of sealing rings are supplied (Ø15 mm, Ø12 mm, Ø9 mm, Ø7 mm, and Ø5 mm).
- Page 24 Terminal Box·Installation Guide 1). Remove the thread cap on supplied adapter. Figure 3-11 Remove Cap on Supplied Adapter 2). Thread the camera cable through sealing ring (together with flexible conduit) and the adapter, and secure the adapter to the conduit. Conduit Sealing Ring of Conduit Adapter...
- Page 25 Terminal Box·Installation Guide 4). Secure the adapter to the “Camera” end with wrench (torque 50 Nm). Figure 3-13 Secure the Adapter to Terminal Box 5. Connect wires to corresponding terminals. This terminal box transmits power without making any change to...
- Page 26 Terminal Box·Installation Guide To Camera RJ45① RJ45② To Source Figure 3-14 Wiring 1). Install a RJ45 head to network cables and plug it to RJ45①.
- Page 27 Terminal Box·Installation Guide 2). Repeat above steps to route source cables through the opposite “Camera” end, connect wires, install a RJ45 head and plug it to RJ45②. 6. Screw the cover back to terminal box. Check to ensure the O-shape ring stays in terminal box. 2).
- Page 28 UD08260B-B...
Need help?
Do you have a question about the DS-2780ZJ-X/316L and is the answer not in the manual?
Questions and answers