Wenglor P1RH001 Operating Instructions Manual

Wenglor P1RH001 Operating Instructions Manual

Reflex sensor with background suppression

Advertisement

Quick Links

Operating Instructions
P1RH001
Reflex Sensor with Background Suppression
EN
Translation of the original operating instructions
Subject to change without notice
Available as PDF file only
Version 2.0
www.wenglor.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the P1RH001 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Wenglor P1RH001

  • Page 1 Operating Instructions P1RH001 Reflex Sensor with Background Suppression Translation of the original operating instructions Subject to change without notice Available as PDF file only Version 2.0 www.wenglor.com...
  • Page 2: Table Of Contents

    Background Teach-In (BT) ............................ 17 7.2 Pin Function E ..................................17 7.2.1 External teach-in..............................17 8 Maintenance Instructions ............................. 19 9 Proper Disposal ................................20 10 Declarations of Conformity............................21 Table of Contents | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 3: General

    The safety precautions and warnings are laid out in accordance with the following principle: SIGNAL WORD Type and source of danger! Possible consequences in the event that the hazard is disregarded. à Measures for averting the hazard. 1 ‒ General | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 4: Limitation Of Liability

    • wenglor assumes no liability for printing errors or other inaccuracies contained in these operating in- structions unless wenglor was verifiably aware of such errors at the point in time at which the operat- ing instructions were prepared.
  • Page 5: Copyrights

    • All rights are reserved by wenglor. • Commercial reproduction or any other commercial use of the provided content and information, in particular graphics and images, is not permitted without previous written consent from wenglor. 1 ‒ General | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 6: For Your Safety

    • The product is not suitable for use in potentially explosive atmospheres. • The product may be used only with accessories supplied or approved by wenglor, or in combination with approved products. A list of approved accessories and combination products can be found at www.wenglor.com on the product detail page.
  • Page 7: Personnel Qualifications

    Read the operating instructions carefully before using the product. Protect the sensor against contamination and mechanical influences. Approvals and Protection Class IND. CONT. EQ 72HL / E189727 For use in class 2 circuits 2 ‒ For Your Safety | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 8: Technical Data

    Mechanical Data Setting Method Teach-In Housing Material Brass, nickel-plated Plastic, PBT Full Encapsulation Degree of Protection IP67/IP68 Connection M12 × 1; 4-pin Output Functions Output Adjustable Parameters Output Push-pull 3 ‒ Technical Data | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 9: Light Spot Diameter

    Switching Distance Deviation Typical characteristic curve based on Kodak white (90% remission). Sr = switching distance dSr = change in switching distance Black, 6% remission Gray, 18% remission 3 ‒ Technical Data | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 10: Housing Dimensions

    68 = supply voltage indicator Complementary Products wenglor offers you the right connection and mounting technology as well as other accessories for your product. You can find this at www.wenglor.com on the product details page at the bottom. 3 ‒ Technical Data | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 11: Scope Of Delivery

    Scope of Delivery • Sensor • Safety precaution • MUTTER-M18-E012 hex nut 3 ‒ Technical Data | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 12: Transport And Storage

    • Protect the product against exposure to direct sunlight. NOTICE Risk of property damage in case of improper storage! The product may be damaged. à Storage instructions must be complied with. 4 ‒ Transport and Storage | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 13: Installation And Electrical Connection

    Risk of personal injury or property damage due to electric current. Voltage-conducting parts may cause personal injury or damage to equipment. à The electric device may be connected by appropriately qualified personnel only. 5 ‒ Installation and Electrical Connection | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 14: Diagnosis

    Check electrical wiring and eliminate the short approx. 5 Hz circuit Over-temperature Disconnect the sensor from the supply voltage and allow it to cool Hardware error Replace the sensor 5 ‒ Installation and Electrical Connection | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 15 Risk of personal injury or property damage in case of non-compliance! The system’s safety function is disabled. Personal injury and damage to equipment may occur. à Required action as specified in case of fault. 5 ‒ Installation and Electrical Connection | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 16: Settings

    To this end, the sensor is connected to a suitable IO-Link master (see product detail page/complementary products). The interface protocol and the IODD can be found at www.wenglor.com in the download area for the respective product. For information on installing and connecting the wTeach2 software and its structure, as well as information on the general functions, see the wTeach2 operating instructions.
  • Page 17: Function Description

    External Teach-in Input Teach in output A1 via teach-in input. With Ub setting active: 1. Apply 18...30 V to pin I for at least 2 seconds (4 seconds maximum). 7 ‒ Function Description | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 18 1. Disconnect pin I or apply 0 V to it for at least 2 seconds (4 seconds maximum). 2. As soon as the voltage is applied to the input, A1 is taught in. 7 ‒ Function Description | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 19: Maintenance Instructions

    Cleaning and inspection of the plug connections at regular intervals are advisable. Do not clean the sensor with solvents or cleaning agents that could damage the product. The product must be protected against contamination during initial start-up. 8 ‒ Maintenance Instructions | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 20: Proper Disposal

    Proper Disposal wenglor sensoric GmbH does not accept the return of unusable or irreparable products. Respectively valid national waste disposal regulations apply to product disposal. 9 ‒ Proper Disposal | P1RH001 ‒ Reflex Sensor with Background Suppression...
  • Page 21: Declarations Of Conformity

    Declarations of Conformity Declarations of conformity can be found on our website at www.wenglor.com in the product’s separate download area. 10 ‒ Declarations of Conformity | P1RH001 ‒ Reflex Sensor with Background Suppression...

Table of Contents