Mtd transmatic lawn tractor illustrated parts manual (35 pages)
Summary of Contents for MTD White OUTDOOR LR 927
Page 1
Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 FORM NO. 769-00705.fm PRINTED IN U.S.A.
For future reference, please copy the model number and the serial number of the equipment in the space below. (Model Number) (Serial Number) Copy the model number here: Copy the serial number here: MTD LLC P. O. BOX 361131 www.whiteoutdoor.com CLEVELAND,OH 44136 DEALER LOCATOR PHONE NUMBER: 800-949-4483 ENGINE INFORMATION The engine manufacturer is responsible for all engine-related issues with regards to performance, power- rating, specifications, warranty and service.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your Riding Mower. Failure to comply with these instructions may result in personal injury.
Page 4
Slope Operation • Keep children out of the mowing area and in watchful care of an adult other than the operator. • Slopes are a major factor related to loss of control • Be alert and turn machine off if children enter the and tip-over accidents which can result in severe area.
Page 5
• After striking a foreign object, stop the engine, • Observe proper disposal laws and regulations. remove the wire from the spark plug and thoroughly Improper disposal of fluids and materials can harm inspect the mower for any damage. Repair the the environment and the ecology.
SECTION 3: ASSEMBLING YOUR RIDING MOWER Unpacking • Remove wing nut from front battery hold-down rod. • Slide the battery cover towards the rear to access • Remove all screws and staples from the crate. the front (negative) terminal. • Holding sides of the crate firmly, lift top of the crate •...
Page 8
chute and a mulching plug are included as loose parts. • To attach the mulching plug now to the unit, follow Follow instructions below to attach this chute. instructions on previous page to attach side- discharge chute to the deck. WARNING: Do not operate the mower if any •...
SECTION 4: KNOW YOUR RIDING MOWER Compare the illustrations in Figure 7 with your riding mower to familiarize yourself with the location of various controls and adjustments. WARNING: The operation of any riding mower can result in foreign objects being thrown into the operator’s eyes, causing severe eye damage.
Page 10
Blade Engagement Pedal • Before leaving operator's position, disengage blade(s), place the shift lever in neutral, engage Use to engage or disengage the blade. parking brake, shut engine off and remove key. Blade Lock Use to lock blade at the engaged position. Using Shift Lever Cutting Height Adjustment Lever This lever is used to regulate...
SECTION 5: OPERATING YOUR RIDING MOWER Using Throttle/Choke Control the left rear wheel. Refer to Figure 2 . The throttle/choke control is Starting Engine used to increase or decrease • Attach the wire to the spark plug. the speed of the engine.The •...
Page 12
Using the Riding Mower • Engage the parking brake by pulling up on the parking brake knob. Observe safety rules listed on pages 3-5 of this manual • Turn ignition key to OFF position and remove key. for safe operation of your mower. NOTE: Do not leave the key in the ON position when •...
SECTION 6: MAKING ADJUSTMENTS Drive Pedal WARNING: Do not at any time make any Adjustment to the Drive Pedal is made at the cable end. adjustment to the mower without first stopping See Figure 9 . engine and disconnecting spark plug wire. •...
Page 14
Seat Position • If the belt is slipping when you depress the blade engagement pedal about 3/4”, loosen the two hex The seat position on the riding mower can be adjusted nuts on the cable. See Figure 10. to maximize the operator’s convenience. •...
Page 15
Test 2: Checking Front to Rear Levelling • Measure the distance from the tips of the blade to the ground. If the two distances are unequal , level • Place the deck in the highest position. the deck side to side. •...
SECTION 7: SERVICING YOUR RIDING MOWER Fuse Replacement Imaginary The fuse is located next to the spark plug under the rear Line Belt Belt frame. Fuses seldom fail without a reason. If the fuse Keeper “A” Keeper blows, the source problem must be corrected or the Deck Belt new fuse will blow again.
Page 17
Variable Speed Pulley WARNING: Do not short battery terminals Spring by making a connection between either two Loaded Spring battery posts or between the positive terminal, Idler Loaded marked + on the battery, and the riding mower Idler frame. Before installing battery, remove metal bracelets, wristwatch bands, rings etc.
Do not jump-start directly at the battery. one hour with a battery charger (output 6 amps) before IMPORTANT: Do not allow positive and negative cable clamps to using your riding mower. Read safe operating touch each other. Do not jump-start a damaged or instructions on battery charger before starting this job.
Page 19
Lubrication • Blade Mounting Torque: 70/90 foot-pounds maximum. See Figure 18 for an illustration of the lube points NOTE: To ensure safe operation, all nuts and bolts described below. must be checked periodically for correct tightness. Lube Deck Spindle Lube Blade Flange Nut Lube...
SECTION 9: OFF-SEASON STORAGE If the machine is to be inoperative for a period longer Battery than 30 days, prepare for storage as follows. • Charge battery fully. The battery loses some of its charge each day when the unit is not used. Riding Mower NEVER store battery without a full charge.
Page 21
Trouble Possible Cause Remedial Action Belt shreds Belt guides or guards incorrectly adjusted Adjust belt guides and guards so that these are approximately 1/16 to 1/8 inch from belt when engaged. Pulleys not aligned Realign pulleys to be within approximately 1/16 inch of each other.
SECTION 11: PARTS LIST FOR MODEL LR927 NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered 700-xxxx, is painted Oyster Gray, the part number to order would be 700-xxxx-0662.
Page 23
Model LR927 Ref. No. Part No. Description Ref. No. Part No. Description 17962 Switch Plate 731-0511 Trim Strip 650-0007 Steering Tube Assembly 735-0674 Floor Pad: LH 683-0033A Steering Support Bracket 735-0266A Floor Pad: RH 683-0178A Front Axle Assembly: RH 736-0105 Bell Washer 683-0179A Front Axle Assembly: LH...
Page 24
Model LR927 NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered 700-xxxx, is painted Oyster Gray, the part number to order would be 700-xxxx-0662.
Page 25
Model LR927 Ref. No. Part No. Description Ref. No. Part No. Description 683-0155A Brake Pedal Assembly 736-0187 Flat Washer 683-0161 Shift Cam Assembly 736-0262 Flat Washer 683-0275A Deck Pedal Assembly 736-0272 Flat Washer .510 X 1.00 X .060 683-0310A Variable Pedal Assembly 736-0300 Flat Washer 710-1017...
Page 26
Model LR927 13 23 Key No. Part No. Description Key No. Part No. Description 683-0152 Pivot Link Assembly 732-0829 Extension Spring 683-0194A Lift Arm Assembly 732-0837 Torsion Spring 710-0376 Hex Screw 5/16-18 X 1.00 Gr.5 736-0119 Lock Washer 5/16 710-3230 Hex Bolt 1/2-13 X 2.75 Gr.5 Spec.
Page 27
Model LR927 NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered 700-xxxx, is painted Oyster Gray, the part number to order would be 700-xxxx-0662.
Page 28
Model LR927 Reference only NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered 700-xxxx, is painted Oyster Gray, the part number to order would be 700-xxxx-0662.
Page 29
Model LR927 Ref. No. Part No. Description 683-0142 Pivot Bar Assembly 683-0160 Bracket Assembly: Hood Pivot 683-0163A Steering Support Bracket 683-0264A Channel Assembly: Front Frame 710-0599 TT screw 1/4-20 x 0.5” 710-1017 AB Screw 1/4-14 x 0.625” 710-1611B TT Screw 5/16-18 x 0.75” 711-0332 Clevis Pin 711-1165...
Page 30
Model LR927 IMPORTANT: For a proper working machine, use Factory Approved Parts. V-BELTS are specially designed to engage and disengage safely. substitute (non OEM) V-Belt can be dangerous disengaging completely. Ref. No. Part No. Description Ref. No. Part No. Description 683-0147A Idler Bracket Assembly 736-0219 Bell Washer...
Page 33
Model LR927 NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered 700-xxxx, is painted Oyster Gray, the part number to order would be 700-xxxx-0662.
Page 35
Model LR927 NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered 700-xxxx, is painted Oyster Gray, the part number to order would be 700-xxxx-0662.
Page 36
Model LR927 Ref. No. Part No. Description 618-0250 Spindle Assembly 683-0150E Deck Assembly 683-0159 Brake Bracket Assembly 683-0173 Deck Belt Cover 710-0134 Carriage Screw 1/4-20 x .62” 710-0191 Hex Bolt 3/8-24 x 1.25” 710-0347 Hex Screw 3/8-16 x 1.75 “ 710-0599 Self-Tapp.
Page 37
Model LR927 Ref. No. Part No. Description 631-0084 Grass Bag Assembly 710-0286 Pan Hd. Machine Screw 1/4-20 x 0.5 710-0564 Hex Screw 1/4-20 x 2.75 710-0825 Hex Screw 1/4-20 x 3.75 712-0298 Jam Nut 712-0397 Wing Nut 726-0271 Push Nut 731-1743A Chute: Bagger 731-1744...
Page 38
Model LR927 Ref. No. Part No. Description Ref. No. Part No. Description 629-04055 Harness Assembly w/o relays 725-1426 Solenoid 12 volt, 100 amp. 710-0134 Carriage Screw 1/4-20 x 0.62” 725-1643 Spring Switch 710-3021 D Screw 5/16-18 x 0.625” 725-1657A Switch: Interlock 712-0271 Sems Nut 1/4-20 736-0607...
Page 39
Safety & Decorative Labels 777I20778 777I20777 IGNITION 777CX00001 CX00001 PLACE MODEL PLATE HERE L'INFORMATION DE MODÈLE ICI MADE IN CANADA FABRIQUÉ AU CANADA 777D07397 777S30199 10 0 HP P TO ENGAGE PARKING BRAKE: FULLY DEPRESS PEDAL WHILE LIFTING KNOB. ® TO START: TO STOP: 1.
Page 40
MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD LLC with MTD LLC does not extend any warranty for products respect to new merchandise purchased and used in the sold or exported outside of the United States, its United States, its possessions and territories.
Need help?
Do you have a question about the White OUTDOOR LR 927 and is the answer not in the manual?
Questions and answers
How do you take steering wheel off ?