Download
Share
Print this page
Frigidaire FRA12EHT2 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Frigidaire Manuals
  4. Air Conditioner
  5. FRA12EHT2
  6. Installation instructions manual
Frigidaire FRA12EHT2 Installation Instructions Manual

Frigidaire FRA12EHT2 Installation Instructions Manual

Installation instructions (english, español, français)
Hide thumbs Also See for FRA12EHT2:

Advertisement

Quick Links

Download this manual See also: Use and Care Manual, Wiring Diagram
Carefully read the installation manual before beginning.
Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may
be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install
the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To
prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.
Do This First (for existing sleeve)
Note that the air conditioner dimensions are: 24" wide,14" high, and 19" deep (without front). Install Air Conditioner
according to these installation instructions to achieve the best performance. Save these installation instructions for
future reference.
NOTE:
DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE
Items in Kit
You may not need all parts in the kit. Discard unused parts.
No.
Hardware
Tapered Spacer Blocks (17" Long)
1
Centering/Support Blocks (
2
1
3
Plastic Divider (
Stuffer Seal (
4
4
1" x 1
1
5
seal
(
" x 25"
1" x 1
2
1
seal
" x 14"
6
(
1" x 1
2
seal
(
1" x 3/8" x 25"
7
seal
(
8
1" x 3/8" x 14"
seal
(
1" x 3/4" x 14"
9

Installation Instructions

READ BEFORE INSTALLING UNIT
For Through-the-Wall Air Conditioners
INSTALLATION WARNINGS AND CAUTION
1
1
1
4 " x 3 " x 1
2
2
2
1
1
" x 4 " x 14 "
)
8
2
2
1
" x 84"
)
2
)
)
)
)
)
Qty.
No.
Trim Frame (side legs)
2
10
" )
4
Trim Frame (top & bottom legs)
11
2
12
Ground Wire (green)
Toothed washer for grounding screw
1
13
3
14
Grounding Screw
2
15
Grille (plastic)
Grille Aluminum
3
16
Nuts (plastic)
2
17
Screw w/washer
2
18
Hardware
Qty.
2
2
1
2
1
1
1
4
4
2020213A0734
1

Advertisement

loading

Related Manuals for Frigidaire FRA12EHT2

Summary of Contents for Frigidaire FRA12EHT2

  • Page 1: Installation Instructions

    Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Pay attention to danger and safety notices. To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: Air conditioners covered in this manual pose an excessive weight hazard.

  • Page 2: How To Install

    Retouch wall sleeve painted surface if needed. 3. If not existing, drill a 3/16" clearance hole for grounding screw through left side of wall sleeve, in a clear area about 3 inches maximum back from front edge of sleeve, using grounding screw and toothed washer. Pull loose end of ground wire out front of sleeve, and temporarily bend it down and around lower edge of sleeve (Fig.2).
  • Page 3 It is very important that these installation instructions are followed so your unit can operate at maximum efficiency. If there is an existing sleeve, and there is an existing rear grille, it needs to be replaced by one that has been shipped with the unit in the accessory kit.
  • Page 4 Top View 2. Attach(1)1" x 3/8" x 25" long seal in the center at the top of the sleeve. Remove the backing paper and press into position. 3. Attach(2)1" x 3/8" x 14" seals to the left and right sides of the sleeve.
  • Page 5 This helps induce a rearward slope on the unit. 5. Attach (1) 1" x 3/8" x 25" long seal in the center at the top of the sleeve. Remove the backing paper and press into position.
  • Page 6 This helps induce a rearward slope on the unit. 5. Attach (1) 1" x 3/8" x 25" long seal in the center at the top of the sleeve. Remove the backing paper and press into position.
  • Page 7 3. Install as shown with the tapered end 1/2" from the back of the sleeve. This helps induce a rearward slope on the unit. 4. Attach (1) 1" x 3/8" x 25" long seal in the center at the top of the sleeve. Remove the backing paper and press into position.
  • Page 8 3. Install as shown with the tapered end 1/2" from the back of the sleeve. This helps induce a rearward slope on the unit. 4. Attach (1) 1" x 3/8" x 25" long seal in the center at the top of the sleeve. Remove the backing paper and press into position 5.
  • Page 9 3. Install to the floor of the sleeve as shown. This helps induce a rearward slope on the unit. 4. Attach (1) 1" x 3/8" x 25" long seal in the center at the top of the sleeve. Remove the backing paper and press into position.
  • Page 10 13. Attach (2) 1" x 1 " x 14" seals along the sides of the sleeve again making sure all seals are flush. 14. Cut the 1" x 1 " x 25" seal to fit the top of the sleeve. The pieces must be fitted flush to the edge of the divider.
  • Page 11 NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille Top View 2. Attach (1) 1" x 3/8" x 25" long seal in the center at the top of the sleeve. Remove the backing paper and press into position. 4.5"...
  • Page 12 12. Attach (2) 1" x 1 " x 14" seals along the sides of the sleeve again making sure all seals are flush. 13. Cut the 1" x 1 " x 25" seal to fit the top of the sleeve. The pieces must be fitted flush to the edge of the divider.
  • Page 13 The previous directions are the preferable way to mount the new rear grill. The unit’s performance is slightly better and the possibility of draughts is reduced. As a last resort, direct mounting of the grille to the unit can be considered.
  • Page 14 Installation Instructions FINISHING INSTALLATION: 1. Install the 1" x 1 " x 84" long stuffer seal between the wall-sleeve and the unit. A flat-bladed screwdriver or putty knife is recommended. 2. Assemble the trim frame by inserting top and bottom pieces into side pieces and snapping into place.