Subscribe to Our Youtube Channel
Related Manuals for Kindermann PRO 7469 000 000
Summary of Contents for Kindermann PRO 7469 000 000
- Page 1 Ceiling Mirror PRO for data and video projectors Ref. no. 7469 000 000 Installation instructions 11.2016...
-
Page 2: Table Of Contents
Safety instructions and warnings ➡ Inspect the device for transport damage at once after receipt. Remove transport protection. ➡ The ceiling mirror is only suitable for use with projectors. ➡ The ceiling mirror must only be installed or repaired by authorised and trained specialists. You should read this instruction/operating manual of the device under all circumstances and observe the safety notes precisely! ➡... -
Page 3: General Description
IR beam via the mirror flap to the receiver and remote-control the projector. However, the best solution is to use a media control, e.g. Kindermann PIXIE plus (no. 5698 000 001) and control via a relay (5698 000 004/6). -
Page 4: Device Description
2 potential-free relay low-voltage contacts. ➡ Deactivation electronics of projector (no. 7465 000 016): automatic control of the projector (Kindermann, EPSON, SANYO, MITSUBISHI) via RS232 when opening and closing the mirror ➡... -
Page 5: Parts Designation And Explanation Of Symbols
2. Device Description 2.4 Parts Designation and Explanation of Symbols Metal frame with aluminium profile Cut-out for installation or disassembly of the projector carriage Holding angle 4 x Extension angle 2 x 4a Attachment angle left/right for ceiling grid, 2 x front 4b Attachment angle for ceiling grid or fixed ceiling, 2 x rear... -
Page 6: Adjusting The Opening Angle Of The Mirror Flap
EXT. CONTROL: 3p plug connection with the optional PCB, deactivation electronics projector (no. 7465 000 016): automatic control of the projector (Kindermann, EPSON, SANYO, MITSUBISHI) via RS232 when opening and closing the mirror. The PIN connections 5 V (100 mA) and (GND) can be used as feedback for a media control (e. -
Page 7: Mounting Of The Ceiling Mirror Pro
3. Mounting of the Ceiling Mirror Read the entire instructions before installation. Check the carrying capacity of the ceiling and the resilience after installation. Remove all protective films of the mirrors after installation! 3.1 Site Issue 3.1.1. Distance from the Canvas For the entire projection beam to hit the mirror surfaces, a distance ratio (ratio of distance to picture width) of at least 1.5 is needed. -
Page 8: Mounting In Suspended Room Ceilings
3.2.1.1 Mounting in Suspended Room Ceilings The ceiling must be able to bear four times the maximum weight of the ceiling mirror and projector, if necessary with reinforcements. First, install the enclosed angles to the metal frame (1): Install angle (4a) left/right front, angle (4b) to the angle (2) with the flat side down, rear. - Page 9 3.2.1.1 Mounting in Suspended Room Ceilings Attention: Observe installation provisions; only use suitable steel dowels to attach the threaded rods to the solid ceiling (not enclosed). Reinforcement of the carrying capacity of the ceiling by installation of the corresponding suspension mounting system of the ceiling supplier to the solid floor ceiling is possible as well.
- Page 10 3.2.1.1 Mounting in Suspended Room Ceilings Cut a section of BxD (B in parallel to the canvas): 505 mm x 490 mm into the suspended ceiling (e. g. plaster- board, panels, wood, etc.) in a suitable location. The cut-out (or any other insertion part) can later be put into the mirror flap.
- Page 11 3.2.1.2 Mounting in Ceiling Grids 60 x 60 cm or 62.5 x 62.5 cm The ceiling mirror is installed in the ceiling instead of a panel. The panel can be inserted into the mirror flap to visually conceal the used ceiling mirror. Remove an element from the ceiling elsewhere.
- Page 12 3.2.1.2 Mounting in Ceiling Grids 60 x 60 cm or 62.5 x 62.5 cm ➡ Connect the mains unit 9 VDC to the socket (13b) and to the 230 V socket, wire the connections for the switch OPEN/CLOSE to the screw terminal OPEN/CLOSE socket (13a). ➡...
-
Page 13: Mounting Of The Projector
4. Mounting of the Projector Prerequisites to the projector: Max. dimensions B=490, L=500 mm, H=variable; max. weight: 15 kg; three or four threaded sleeves (M3, M4, M5 or M6) on the bottom; attachment area between 100 and 480 mm. The attachment material is enclosed: 4 threaded spacer sleeves, 4 x screw set with the corresponding washers M3, M4, M5, M6;... -
Page 14: Positioning The Projector In The Ceiling Mirror
4.2 Positioning the Projector in the Ceiling Mirror First insert the projector carriage into the cut-out (1a) in the frame structure with the rear carriage axis (9f), then push this axis in the guide first towards the canvas, then insert the front carriage axis (9e) and finally place the projector in the projection position. -
Page 15: Removing The Projector For Servicing
4.3 Installing the Sight Screen The enclosed sight screen (10) is finally placed above the installation cut-out (1a) in the ceiling mirror with the mirror flap open. The angled end is inserted into the groove of the aluminium profile. We recommend installing a box in the ceiling instruc- tion at the installation site as well to cover up dust collection and undesired views into the open ceiling. -
Page 16: Maintenance And Care
Additionally, observe dust deposits or other flammable or obstructing materials, remove or clean them if necessary. 6. Dimensions and Dimension Sketch 7469 000 000 GB 2016-11 / 8 42 005 Subject to alterations Printed in Germany Kindermann GmbH · Mainparkring 3 · D-97246 Eibelstadt · E-Mail: info@kindermann.de · www.kindermann.com...
Need help?
Do you have a question about the PRO 7469 000 000 and is the answer not in the manual?
Questions and answers