Advertisement
Quick Links
Premium Cordless
Power Brush System
VAC-420
Cordless Power Brush
EBK360
This manual covers the operation of:
VAC-420 EBK360 Cordless Electric Turbo Brush
VAC-421 Power Tube Battery Pack & Telescopic Wand
VAC-422 Battery Charger for Power Tube
All items are available for purchase separately or as part of K-VAC-420 kit
VAC-422
Charger
USER MANUAL
VAC-421
Power Wand -
battery pack and
telescopic wand
Advertisement
Related Manuals for Valet VAC-420
Summary of Contents for Valet VAC-420
- Page 1 EBK360 This manual covers the operation of: VAC-420 EBK360 Cordless Electric Turbo Brush VAC-421 Power Tube Battery Pack & Telescopic Wand VAC-422 Battery Charger for Power Tube All items are available for purchase separately or as part of K-VAC-420 kit...
- Page 2 • • • • • This device complies with the following EG directives: • 2014/35/EU – Low Voltage Directive • • 2014/30/EU – EMC directive • 2011/65/EG – RoHS directive • Attention! • Do not use the device without • having read the instructions for use •...
- Page 3 ATTENTION! This device is not suitable for the recovery of hazardous dust. • This device is intended for dry use only and must not be used or stored • outdoors in wet conditions. Use only original manufacturer’s parts. Use of non-original •...
- Page 4 Power Brush System Height adjustment pedal Wand release pedal Neck release pedal Headlight To your vacuum hose POWERBRUSH On/Off Switch* Charger input Battery charge indicator POWERWAND * On/Off Switch Notes • Short Press to display battery charge level. • Long Press to turn on or off.
- Page 5 Do not vacuum up heavy, hard or sharp-edged objects. You could block • and damage the electric brush. Don’t operate the electric brush over exposed cables. • The electrical connector must be checked regularly for damage. If there • is any damage, the electrical connection piece must be replaced immediately by a qualified small appliance repair professional.
-
Page 6: Operation
Charging Shipping a fully charged Lithium-Ion Battery is prohibited. A new battery just ‘out of the box’ will only have a partial charge. To ensure a full battery charge, completely charge the battery before using. It is always best to disconnect the charger from the battery after full charge has been achieved. - Page 7 Neck release pedal Height Adjustment Pedal 5-position height adjustment. Level 1 is the lowest setting and is suitable for low pile carpets and level 5 is best for heavier/shaggy carpets. The operator should change the height adjustment until there is an acceptable push/pull resistance on the surface to be cleaned.
- Page 8 The push/pull resistance can also be lowered if • your vacuum equipped with adjustable vacuum/suction control. Reducing RPMs of the • vacuum will reduce the push/pull resistance. Cleaning efficiency is only slightly diminished as adjustments are made. It is suggested that the brush roller is switched off when cleaning delectate floor coverings, such as sensitive wool carpets, some deep-pile carpets, carpet fringes, animal skins or similar.
- Page 9 Eliminate the cause of the error. If necessary, clean • the brush roller as described under Care. After a short wait (> 15 seconds) the device can be • switched on again. Maintenance and Care Attention! Remove the powerbrush from the power source before conducting any work on the device (disconnect the powerhead from the battery wand).
- Page 10 Maintenance and service Attention! It is strongly recommended that all maintenance and service work be conducted only by the manufacturer or a trained and experienced small appliance repair professional. Do not open the battery pack • If the electrical connector is damaged, it must be •...
- Page 11 Use scissors to cut away any threads and hair wrapped around the brush roller.
-
Page 12: Year Warranty
3 YEAR WARRANTY REgiSTER YOUR WARRANTY SALES - SERViCE - SPARES 1300 551 991 www.valet.com.au © 2024 Ness Corporation Pty Ltd ABN 28 069 984 372 Photographs are used for illustrative purposes only. Design and specifications may vary.
Need help?
Do you have a question about the VAC-420 and is the answer not in the manual?
Questions and answers