1. Manuals
  2. Brands
  3. Planet Manuals
  4. Switch
  5. MGSW-24160F
  6. Quick installation manual

Planet MGSW-24160F Quick Installation Manual

Managed metro ethernet switch
Hide thumbs Also See for MGSW-24160F:
Table of Contents

Advertisement

Quick Links

Download this manual
Managed Metro Ethernet Switch
MGSW-24160F
Quick Installation Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MGSW-24160F and is the answer not in the manual?

Questions and answers

Related Manuals for Planet MGSW-24160F

Summary of Contents for Planet MGSW-24160F

  • Page 1 Managed Metro Ethernet Switch MGSW-24160F Quick Installation Guide...

  • Page 2: Table Of Contents

    Table of Contents 1. Package Contents ................. 3 2. Requirements ..................4 3. Wiring the Power Inputs ............... 5 3.1 Grounding the Device ..............6 4. Terminal Setup ..................7 4.1 Logging on to the Console .............. 8 4.2 Configuring IP Address ..............9 4.3 Saving the Configuration ..............

  • Page 3: Package Contents

    1. Package Contents Thank you for purchasing PLANET L2+ Managed Metro Ethernet Switch. The description of this model is as follows: Model Description L2+ 8-Port 10/100/1000T + 12-Port 100/1000X SFP + MGSW-24160F 4-Port 10G SFP+ Managed Metro Ethernet Switch In this guide, the term “Managed Metro Switch” refers specifically to the MGSW-24160F.

  • Page 4: Requirements

    2. Requirements z Workstations running Windows 10/11, MAC OS 10.15 or later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols. z Workstations are installed with Ethernet NIC (Network Interface Card). z Serial Port Connection (Terminal)  The above Workstations come with COM Port (DB9) or USB-to-RS232 converter.  The above Workstations have been installed with terminal emulator, such as Tera Term or PuTTY.

  • Page 5: Wiring The Power Inputs

    DC 1 Alarm DC 2 1.5A max. Figure 3-1: MGSW-24160F Inlet Power Socket Users can plug the Managed Metro Switch into either AC or DC power source for the connectivity. The specifications of the DC/AC power source are as follows.

  • Page 6: Grounding The Device

    DO 1 Max. Fault Alarm Loading: 24V, 1A Alarm 10 12 14 16 18 20 17 19 11 13 15 1000 LNK/ACT Reset DC Input: 36-60V 10/100 LNK/ACT 50/60Hz DC 1 Alarm DC 2 1.5A max. Figure 3-4: MGSW-24160F Earth Grounding...

  • Page 7: Terminal Setup

    4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and the RJ45 cable to RJ45 console port of the Managed Metro Switch as shown in Figure 4-1. PC / Workstation with Terminal Emulation Software Managed Switch...

  • Page 8: Logging On To The Console

    (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. PLANET Technology Corp. Made in Taiwan Figure 4-3: MAC ID Label Enter the default username and password, and then set a new password according to the rule-based prompt and confirm it. Upon success, press...

  • Page 9: Configuring Ip Address

    Figure 4-5. Figure 4-5: IP Information Screen  Configuration of the IP address 1. At the “MGSW-24160F#” prompt, enter “configure”. 2. At the “MGSW-24160F(config)#” prompt, enter the following command and press <Enter> as shown in Figure 4-6. MGSW-24160F(config)# ip address 192.168.1.100 mask 255.255.255.0 MGSW-24160F(config)# ip default-gateway 192.168.1.254...

  • Page 10: Saving The Configuration

    IP address setting immediately. You can access the Web interface of Managed Metro Switch through the new IP address. 4.3 Saving the Configuration At the “MGSW-24160F#” prompt, enter “copy running-config startup- config” as shown in Figure 4-7. Figure 4-7: Saving Current Configuration Command Screen If you are not familiar with console command or the related parameter, enter “?”...

  • Page 11: Starting Web Management

    5. Starting Web Management The following shows how to start up the Web Management of the Managed Metro Switch. Note the Industrial Metro Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address as shown in Figure 5-1.
  • Page 12 3. After logging in, you will be prompted to change the initial password to a permanent one. Figure 5-3: Create a New Password 4. Once the password change is complete, re-enter the web interface using your new password and the main screen appears as Figure 5-4 shows. Figure 5-4: Web Main Screen of Managed Metro Switch The Switch Menu on the left of the Web page lets you access all the commands and statistics the Managed Metro Switch provides.

  • Page 13: Saving Configuration Via The Web

    Figure 5-6: Switch Sub-menu Now, you can use the Web management interface to continue the Switch management. Please refer to the user’s manual for more. 5.2 Saving Configuration via the Web To save all applied changes and set the current configuration as a startup configuration, the startup-configuration file will be loaded automatically across a system reboot.
  • Page 14 2. Press the “Apply” button to save running configuration to start up configu- ration. Figure 5-8: Save Configuration...

  • Page 15: Recovering Back To Default Configuration

    Max. Fault Alarm Loading: 24V, 1A Alarm 10 12 14 16 18 20 17 19 11 13 15 1000 LNK/ACT Reset DC Input: 36-60V 10/100 LNK/ACT 50/60Hz DC 1 Alarm DC 2 1.5A max. Reset Button Figure 6-1: MGSW-24160F Reset Button...

  • Page 16: Customer Support

    7. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team. PLANET online FAQs: https://www.planet.com.tw/en/support/faq Support team mail address: support@planet.com.tw MGSW-24160F User’s Manual https://www.planet.com.tw/en/support/downloads?&method=keyword&keyword...

Table of Contents