Altronix netway NetWay8G Installation Manual page 2

Fig. 1
NetWay8G - Front Panel
NetWay8G - Rear Panel
Port Status
All Ports Off Sequential LED Port Scan
Port Off
Port On
Class 4 detection Port
Non-compliant Device
Port Overload Fault
4 Port Overload Grouped
8 Port Overload Grouped
Installing a NetWayXT/NetWayXTX repeater module:
NetWayXT will work only with PoE devices. NetWayXTX will work with PoE/PoE+ devices.
1. Mount NetWayXT/NetWayXTX in desired location utilizing the mounting hole (Fig. 2, pg. 2).
Use a proper fastener and/or wall anchor when securing NetWayXT/NetWayXTX to the wall.
2. Connect structured cable from port marked [OUT] on NetWay to port marked [IN] on the
NetWayXT/NetWayXTX (Fig. 2, pg. 2).
3. Connect structured cable from port marked [OUT] on NetWayXT/NetWayXTX to the
PoE/PoE+ camera/edge device or next NetWayXT/NetWayXTX repeater (Fig. 2, pg. 2).
4. Port status LEDs will illuminate on NetWayXT/NetWayXTX indicating the port is operational
(refer to LED Definitions, pg. 2).
5. Power LED will illuminate indicating 12VDC output.
Status
OFF Indicates it is connected as 10Base-T or no link.
ON Indicates it is connected as 100Base-TX.
Blinking
www.altronix.com
1a 1b
Port Status and LED Flash Codes:
Flash Codes
OFF
ON
Blinks 2 times
2Hz
5Hz
5Hz
5Hz
Port LED Definitions for NetWayXT and NetWayXTX Repeaters:
NetWayXT
Green LED
-------
1d
1c 1e 1f
1g 1h
Enables power to PoE devices.
Will prevent port from turning on.
Will prevent port from turning on.
4 LEDs. Will prevent ports from turning on.
LEDs 1-8 Power Supply Overload for ports 1-8.
Power OUT
Yellow LED PoE/PoE+ Output LED
Indicates no link. No PoE/PoE+ Output
Indicates a link. Normal PoE/PoE+ Output
Indicates activity.
- 2 -
1a OUT 1-8: Structured cable to PoE compliant
cameras/edge devices.
1b IN 1-8: Structured cable to ethernet switch or video server.
1c LED(s) 1-8: Port status LEDs.
1d Reset: Restores unit to factory settings.
1e USB Port: For future use.
1f Ethernet: For future use.
1g IEC 320 Connector: 115/230VAC (grounded line cord included).
1h Built-in battery charger: Charges stand-by batteries for
applications requiring back-up,
(optional rack mount battery enclosure available - RE2)
Description
No devices connected
LED OFF
LED ON
NetWayXT
NetwayXT
Structured
Repeater
Power
Cable from
LED
NetWayG
Structured Cable
to IP Camera/
Edge Device
or next
NetWayXT
www.altronix.com
IN
NetWayXTX
PoE/PoE+ Input LED
No PoE/PoE+ Input
PoE/PoE+ Input
- - - - - - - - -- -- --
Fig. 2 - NetWayXT/NetWayXTX
NetWayXTX
Structured
Cable from
NetWayG
PoE/PoE+
Output
LED
PoE/PoE+
Structured Port Status
Input
Cable to LEDs
LED
PoE/PoE+
Camera/Device or
next NetWayXTX
Yellow LED
Indicates no link.
Indicates a link.
Indicates activity.
NetWay8G