Lumitec SeaBlazeX2 Installation Instructions

S ea B la z eX 2 Wirin g In s tructio ns
Due to the high lumen output of the SeaBlazeX2 light, su ciently rated wiring and electrical
components must be used to minimize voltage drop to the lights. When connecting multiple
INSTALLATION INSTRUCTIONS
SeaBlazeX2 lights to a common switch this becomes even more critical. THE TYPICAL
RECOMMENDATION IS TO SELECT WIRING SYSTEM COMPONENTS TO ENSURE THAT VOLTAGE DROP
• ORIENTATION IS VERY IMPORTANT! Lights should be mounted with the logo in an upright position
FROM POWER SOURCE TO THE LIGHTS DOES NOT EXCEED 3%. To simplify the installation on vessels
• Lights must be operated on an appropriately fused or circuit breaker protected circuit.
with multiple lights Lumitec has introduced a remote switch internal to the SBX2 light, allowing for
• Lights are not recommended for mounting on running surfaces (e.g., the bottom surface of a hull)
less expensive low current wire and components to be used during the installation.
• For best performance, lights should be mounted below the waterline
• Bottom paint is not required, however lights can be painted with any bronze-safe paint if desired.
• Allows for more lights to be controlled by a single switch
• Switch placement can be much further from lights
Operation:
An abrupt OFF/ON toggle of your standard (SPST) switch allows SeaBlazeX2 to transition through various light output modes.
• Fewer channels required on your digital switching system
SeaBlazeX2 SPECTRUM Light Output Modes 3-WIRE CONNECTION
Light will cycle through all available colors within the rst 20 seconds, (including
TOGGLE SWITCH or DIGITAL SWITCH - Max current draw 0.1 Amps per light (allows PLI functionality)
white). A brief OFF/ON toggle will allow the user to select any discrete color during
the cycle. After 20 seconds without interruption, the light will continue a full color
Fuse/Breaker
Switch
cycle over a period of 3 minutes - Discrete colors can still be chosen during the 3
minute cycle. If a discrete color is not selected, the light will repeat the 3 minute
6A per light
cycle continuously. Light resets after power is o for more than 3 seconds.
X # of lights
(@ 12vDC)
Mounting Location:
Mounting surfaces should be at, clean, dry, and free of any existing hardware or holes. Before mounting ensure that the light will not interfere with the
operation of engines, trim tabs, rudders, etc. Ideal mounting locations include transoms, the side and back surfaces of engine brackets, and the
undersides of dive platforms. For maximum performance SeaBlazeX2 lights should be mounted 6" to 16" below the waterline. Installation at depths
greater than 36" is not recommended.
BATTERY
10-30vDC
Mounting your SeaBlazeX2 light:
Tape the mounting template in the desired mounting location. Drill holes for the mounting screws and wire boss as indicated on the mounting template.
NOTE! The mounting screws provided with your SeaBlazeX2 light, while very corrosion resistant, are softer than typical steel screws. Extreme care must
2-WIRE CONNECTION
be taken when driving screws to prevent screw heads from shearing o . The diameter of the pilot hole required for the mounting screws will depend
largely on the composition and thickness of the mounting surface.
Fuse/Breaker Switch
HIGH CURRENT SWITCH or RELAY - 6 Amps per light (@ 12vDC)
Size pilot holes so that only moderate torque is needed to drive the screw into the mounting surface. Typically this hole size will be slightly smaller than
6A per light
CONNECTIONS MUST
the outside diameter of the widest threads. Test the size of the mounting hole prior to installation. Carefully turn screws to avoid breaking them. If screw
X # of lights
(@ 12vDC) BE DURABLE AND
is too tight, back out and re-size screw hole. When drilling berglass, slightly countersinking the hole using a 3- uke countersink bit will reduce gelcoat
WATERPROOF
chipping. Thoroughly coat the back surface of the SeaBlazeX2 light with a marine-grade sealant designed for below-waterline applications. Dab
additional sealant on the holes in the mounting surface, forcing some sealant into the holes. Extreme care should be taken to properly seal the
SPLICE Power
through-hull (wire) hole to prevent water intrusion. Press the SeaBlazeX2 rmly into place to bed it in the sealant. Tighten the mounting screws evenly.
& Swtich (Orange)
Sealant should be forced from all sides as the light is tightened down.
Wires Together
Since 2008 the SeaBlaze line of underwater lights has established the
BATTERY
industry benchmark for performance, quality, and value. Introducing
10-30vDC
the new standard: SeaBlazeX2. Completely surface mount, the
SeaBlazeX2 housing is constructed of carefully formulated bronze alloy
with a designed underwater service life of more than 50 years. The
Limited Warranty
circuitry is completely self-contained and tested to rigorous military
The product is warranted to be free from defects in workmanship and materials
standards for EMI, transient voltages, temperature extremes, and
for a period of one year from the date of original purchase. Lumitec is not
mechanical shock and vibration. Exclusive thermal foldback
responsible for product failure caused by abuse, neglect, improper installation,
technology ensures the light can operate above water inde nitely
or failure in applications other than those for which it was designed, intended,
without damage. And with a lower pro le and smaller footprint than
and marketed. Note that some surface corrosion is expected when bare metals
most other lights, mounting options are no longer limited to wide at
are used in a marine environment. Corrosion of any metal will be especially
aggressive if installation is improper, if bonding is improper or if stray currents transom areas.
are active in the vicinity of the boat. Lumitec shall not be liable for defects
related to such corrosion. Should your Lumitec product prove defective during
MOUNTING TEMPLATE ON REVERSE
the warranty period, promptly notify Lumitec, and return product, freight
prepaid. Lumitec will, at its option, repair or replace the product or defective
portion without charge for parts or labor, or, at Lumitec, Inc.'s option, refund
purchase price. Products repaired or replaced under this warranty shall be
warranted for the unexpired portion of the warranty applying to the original
product(s). No warranty or a rmation of fact, express or implied, other than as
set forth in the limited warranty statement above is made or authorized by
Lumitec, Inc. Any liability for consequential and incidental damages is expressly
See reverse for wiring instructions and warranty information
disclaimed. Lumitec liability in all events is limited to, and shall not exceed, the
purchase price paid.
Orange - Switch Line
Red - Power Line
Black - Negative Line
Red - Power Line
Black - Negative Line
(Red)
• Will allow for PLI color control via
compatible digital switching system
through a Multi Functional Display (MFD)
SeaBlazeX2 Dual Color Light Output Modes
1 – Cross-Color Fade – gently undulating color mix,
Blue, 3 – On White
Orange
- Switch Line
Thread the wire strain relief from inside the boat along the power wire.
Press it rmly into the wirehole to properly seal and prevent water
intrusion. Allow the sealant to cure thoroughly per the manufacturer's
instructions prior to returning the vessel to the water.
Note: Any time a hole is bored into a vessel's hull (for example mounting
screws for transducers, dive platforms, through-hull ttings, etc.), the
possibility of water intrusion into the hull or completely into the vessel
exists. Water intrusion may result in signi cant structural damage to a
vessel or the vessel sinking. Considerable care should be taken to
ensure that the through-hull hole is thoroughly sealed on both sides of
Drill this hole for
the hull. Additionally, the back (inside) surface where the wire exits the
the power cord.
through-hull hole should be carefully sealed using the wire strain relief.
Under Voltage Behavior
Size Drill Bit Appropriately
If the voltage at the device is less than 10V when the device is on, the
device will gradually dim to minimum brightness. Factors which may
Mounting Screw Minimum Diameters
result in under voltage conditions include insu cient wire gauge, bad
battery cell, bad connection at switch, connectors, fuse and/or circuit
breaker. Lumitec, Inc. assumes no responsibility whatsoever for any
damage, loss, or injury that may result from the incorrect installation of
this product, including but not limited to the vessel sinking, structural
damage due to water intrusion, electrical malfunction, etc.
Voltage: 10 - 30vDC
12vDC Amps: 5A
24vDC Amps: 2.5A
Voltage: 10 - 30vDC
Color Temperature: 6500K (White)
12vDC Amps: 5A
24vDC Amps: 2.5A
Lumitec
Color Temperature: 6500 (White)
1405 Poinsettia Drive, Suite 10
Delray Beach, FL 33444
www.lumiteclighting.com
To use the 3-wire system, simply
connect the red and black 10-30VDC
lines to an appropriately fused power
buss with constant power and the
Orange wire to a switched +10-30VDC
buss referenced to the same ground
as the power lines.
NOTE: The SBX2 can also be wired in a
standard two wire installation as well
by simply connecting the red and
orange wires together and powering
via an appropriately rated switched
power buss.
Top
When predrilling mounting screw holes use an
appropriately sized bit for the composition and
thickness of the mounting surface.
Most applications will require a drill bit sized
larger than the minimum diameter of the screw,
but smaller than the maximum thread diameter.
1/2"
2 – On
Hole centers for
mounting screws
(see instructions for
sizing).
0.140 " 0.190 "
600718_A