CONGRATULATIONS on choosing General Floorcraft for your Floor Maintenance Equipment Line. Welcome to the family of General Floorcraft. We appreciate your business and will do everything in our power to keep you satisfied. As a family member of America’s Oldest and Most Trusted Manufacturer of Floor Maintenance Equipment, you purchased the highest quality equipment with the best warranties in the industry.
MACHINE ASSEMBLY WHEN ORDERING PARTS, ALWAYS USE PART NUMBERS DO NOT USE REFERENCE NUMBERS! GIVE MODEL NUMBER, SERIAL NUMBER AND PART NUMBER WHEN ORDERING. THE SERIAL NUMBER AND MODEL NUMBER WILL BE FOUND ON THE TOP OF THE APRON BY THE RIGHT WHEEL. 1500 DC-1 Page 3...
HANDLE ASSEMBLY - 500022 110 V PLUG Cable, Heavy Duty 50' Red 220v Pre-5/2013 Old 606533 C 607033 G 607533 I 608033 L 606033 M Ref. # Part # Description Required Ref. # Part # Description Required 501044 Switchbox, Front and Back Polished 501054 Nut, Lock with Nylon Insert 501028...
Page 8
All information and specifications printed in the manual and parts list are current at the time of printing: however, because of General Floorcraft’s policy of con- tinual product development, we reserve the right to make changes at any time without notice. If any additional...
Page 9
When servicing machine, use only manufacturer’s replacement parts. All service should be performed only by General Floorcraft authorized service centers. Use extra care when cleaning stairs. Do not immerse or use this machine in standing water. Such use can cause electric shock.
Page 10
SAFETY & GROUNDING INSTRUCTIONS WARNING! DO NOT use extension cords more than 50 feet (15 m) long. Replace the cord if the ground pin is damaged or broken. FAILURE TO COMPLY WITH THE ABOVE WARNING INSTRUCTIONS WILL VOID THE WARRANTY.
Page 11
ASSEMBLY & OPERATION INSTRUCTIONS PREPARE THE MACHINE FOR OPERATION (SETTING UP) The 1500 DC-1 machine is packed in two separate boxes. The machine is in box 1 of 2, and the handle is in carton 2 of 2. Unpack the machine and handle carefully. Insert the handle into the handle adaptor socket and tighten the two square head screws to hold the handle firmly in place.
MANEUVERING & STORAGE INSTRUCTIONS MANEUVERING & STORAGE INSTRUCTIONS 1.) The machine is designed to operate in a straight forward walk method and NOT from side to side as is a standard rotary floor machine. As you will notice, the wheels are in contact with the floor at all times.
LORSQUE LA MACHINE EST REMIS Vous êtes responsable de l'inspection de la commande dès réception . General Floorcraft n'est pas re- sponsable des dommages si vous avez signé pour les marchandises et de ne pas noter les dommages sur le bon de livraison .
CONSIGNES DE SÉCURITÉ ATTENTION! Pour réduire le risque d'incendie , de choc électrique ou de blessure: Ne pas permettre que soit utilisé comme un jouet. Une attention particulière est nécessaire lorsqu'il est utilisé par ou près des enfants . Ne manipulez pas la fiche ou l'appareil avec les mains mouillées . Ne pas débrancher en tirant sur le cordon .
SÉCURITÉ ET INSTRUCTIONS DE MISE ATTENTION! NE PAS utiliser de rallonges de plus de 50 pieds (15 m) de long. Remplacez le cordon si la broche de terre est endommagé ou cassé. NON-RESPECT DES CONSIGNES DE GARDE ci-dessus ANNULE LA GARANTIE. INSTRUCTIONS DE MISE Cet appareil doit être mis à...
MONTAGE ET MODE D'EMPLOI PRÉPARATION DE LA MACHINE POUR LE FONCTIONNEMENT (mise en place ) Le 1500 DC-1 Machine est emballé dans deux boîtes séparées. La machine est en zone 1 de 2, et la poignée est en carton 2 de 2. Déballez la machine et manipuler avec précaution. Insérez la poignée dans la prise de l'adaptateur de poignée et serrez les deux vis à...
Page 17
MANOEUVRER & STOCKAGE INSTRUCTIONS COMMENT MANOEUVRER VOTRE MACHINE ETAGE: 1.) Soulever légèrement la poignée et la machine ira vers la droite. Lorsque vous élevez, plus vite il ira vers la droite. 2.) Abaissez la poignée et la machine ira vers la gauche. Le plus vous baissez, plus vite il ira vers la gauche. 3) Note:.
All other components, except as noted, carry a ONE (1) year warranty. Parts and labor are covered in accordance with our flat rate schedule. Warranty claim form must be filled out and returned to General for labor or parts claim.
Page 19
Product & Warranty Registration Form Thank you for registering your General Floorcraft Equipment. As a registered user, you will receive free technical support, special offers and new product information. By returning this form, we can also confirm the date of purchase of your equipment for your warranty from the date of purchase. Please attach a copy of your invoice with the serial number(s) on it as proof of purchase.
Need help?
Do you have a question about the 2000 DC-1 and is the answer not in the manual?
Questions and answers