Related Manuals for Propel Trampolines ENDEAVOR
Summary of Contents for Propel Trampolines ENDEAVOR
- Page 1 ENDEAVOR Please offer Vehicle Identification NO. and attach videos/ photos to illustrate your problems before contacting Propel EV for warranty assistance and/or replacement parts. Vehicle Identification NO.
-
Page 2: Table Of Contents
ENDEAVOR Please read this manual carefully before using the product to fully understand the components and functions to operate it safely. PROPEL EV does not assume any responsibility for accidents and injuries caused by personal decisions or failure to read this manual. -
Page 3: Safety Warning And Disclaimer
ENDEAVOR SAFETY WARNING AND DISCLAIMER WARNING Throughout the design and manufacture of this product, safety and stability have been our primary focus but skateboarding inherently can be a dangerous activity. We cannot judge the environment where you use this product, your skills, your physical condition and other factors that may cause the accident, so we cannot promise the safety of your use of this product. - Page 4 ENDEAVOR covered by the warranty. Except for the specific models provided for DIY, any modification and assembly of the skateboard will destroy the stability of the board's performance. Once you assemble or modify the board privately, your board will not be covered by the warranty.
-
Page 5: Components And Check Items
ENDEAVOR COMPONENTS AND CHECK ITEMS -component name ⑤ ③ ① ② ④ ⑥ ⑧ ⑦ ⑨ ⑩ ① Wheel ⑥ Deck Battery Holder ② Upper Arm ⑦ Belt Handle ③ Lower Arm ⑧ Belt Gear Power Button ④ Shock absorber ⑨... - Page 6 ENDEAVOR Check items before use: (1) Check the power of the skateboard and the remote control to ensure that the power is sufficient. (2) Ensure adequate tire pressure. Do not over-inflate the tires in hot weather to prevent punctures. (3) Check whether the screws are loose before use and often throughout ownership.
-
Page 7: Features
ENDEAVOR FEATURES 1.Power ON/OFF ◎ ENDEAVOR S POWER ON: The power switch is a self-reset switch, which may be installed on the top or bottom of the skateboard depending on the model. ROLLING START. This board is equipped with “rolling start” which means you shove/push the board ahead of you for 50-100 cm and it will turn itself on (You will hear a beep). - Page 8 ENDEAVOR (2) Turning force ② ① ① Lock nut ② Adjustment rod 1. Use a 13mm wrench to loosen the lock nut counterclockwise . 2. Use the H4 hexagon wrench to turn the adjusting rod clockwise to increase the pre-tightening force, and counterclockwise to decrease the pre-tightening force.
-
Page 9: Remote Control
ENDEAVOR REMOTE CONTROL Part1 ENDEAVOR S Pairing 1. Press and hold the power button for 3 seconds to turn on. 2. Turn on the power switch of the board, press and hold the power switch for more than 5 seconds, the power light flashes, and it enters the pairing state. - Page 10 ENDEAVOR Remote functions 1. Scroll wheel: Push the wheel forward to accelerate, and push the wheel backwards to slow down. 2. Cruise control During acceleration, short press the power button once to switch to the cruise mode. Pull the acceleration/deceleration wheel to end the cruise state.
- Page 11 ENDEAVOR Part2 ENDEAVOR PRO Display screen Accelerate/Brake gear Power on/off button Setting button USB charging port Hang strap (Remote) ① ② ③ ① Forwad/Reverse ② Skateboardpower ③ Remote power ④ Speed ⑦ ④ ⑤ Current ⑥ Mileage ⑦ Speed mode ⑥...
- Page 12 ENDEAVOR Setting Long press the power button to turn on, long press the setting button to enter the parameter setting menu, click the setting button to switch the menu interface, press and hold the setting button until the menu name...
- Page 13 ENDEAVOR Pairing Enter the Pairing menu according to the above setting method, and press and hold the function button until Paring flashes. After turning on the power button of the skateboard, it will automatically match. “Pairing succeeded” on the remote control shows that the pairing is successful.
-
Page 14: Warranty And Maintenance
ENDEAVOR WARRANTY AND MAINTENANCE Within six months from the date of receipt by the user, non-human damage to the main body of the body can be repaired free of charge. Electronic components such as motors, controllers, remote controls, batteries are guaranteed for three months. -
Page 15: Customer Service
We will promptly provide you with a solution based on your feedback. Note: All pictures are for illustration and illustration only. Different series of Endeavor products may differ in appearance and material. Please refer to the actual product. - Page 16 CYCLEAGLE INTELLIGENT EQUIPMENT(WEIHAI) CO.,LTD Email: services@cycleagle.com/mkt@cycleagle.com Web: www.ridepropel.com...
Need help?
Do you have a question about the ENDEAVOR and is the answer not in the manual?
Questions and answers