1. Important Safety Instructions SAVE THESE INSTRUCTIONS This manual contains instructions and warnings that must be followed during the installation and operation of the product described in this manual. Failure to comply may invalidate the warranty and cause property damage or personal injury. USB Charger/Hub Unit: •...
2. Overview Your charging station is an all-in-one solution for storing, charging and syncing for up to 32 smartphones. Your charging station can be conveniently mounted to walls as well as used for stationary desktop installations. To prevent theft and device tampering, your charging station enclosure comes equipped with locking steel doors.
Storage Shelves (Hold up to 16 Devices Each.) 32-Port USB Charger/Hub Unit Power Cord Access Holes with 5-15P (CSD32USB) Right-Angle Plug (1 Opening Located on Each Side.) 3-Point Lock Padlock Hasp (Optional. Assembly Required, See Section 3.4 for More Information. Lock Not Included.) Rear Panel with Keyhole Wall Mount Slots (See Section 6 for More Information.)
4. Setup Caution! Read All Instructions and Warnings Before Installation! Warning: Charging stations can be extremely heavy. Do not attempt to unpack or mount the charging station without assistance. Use extreme caution when handling the charging station and be sure to follow all handling and installation instructions.
Repeat for all devices. Tripp Lite offers individual and 10-pack cables for Apple devices using USB to 30-Pin or USB to Lightning™ cables, as well as individual and 10-pack cables for USB 3.0 or 2.0 devices using USB-A (male) to 5-Pin Micro B (male) cables.
6. Wall Mounting For wall mounting, you will need: • Level 16” • Appropriate tools for wall mounting • Appropriate hardware for wall mounting (not included) Warning: Do not attempt to mount the charging station to the wall with any personal electronic devices inside.
7. Desktop Placement 14” 14” BOTTOM 355.6 mm 355.6 mm 2” 2” 50.8 mm 50.8 mm FRONT FRONT 2 13/16” 18” 2 13/16” 18” 17.56 mm 457.2 mm 17.56 mm 457.2 mm WARNING: For desktop applications, always install the charging station in a structurally sound area with a level surface that is able to bear the weight of the charging station, all equipment that will be installed in the charging station and any other enclosures and/or equipment that will be installed nearby.
Transmission Speed USB 2.0: Up to 480 Mbps Power Requirement Input: 110-120V, 8A, 50/60 Hz (CSD32USB) or 230V, 5A, 50 Hz (CSDXB32USB, CSDXS32USB) Output: 5.0V, 2.4A Max (per USB port) Operating Temperature 32° to 86° F / 0° to 30° C...
Product Registration Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!* * No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
1. Instrucciones de Seguridad Importantes CONSERVE ESTAS INSTRUCCIONES Este manual contiene instrucciones y advertencias que deben observarse durante la instalación y la operación del producto aquí descrito. El no hacerlo puede invalidar la garantía y causar daños materiales o lesiones personales. Unidad de Cargador/Hub USB: •...
2. Descripción General Su estación de carga es una solución todo en uno para almacenamiento, carga y sincronización de hasta 32 smartphones. Su estación de carga puede instalarse en paredes de manera conveniente, así como configurarse para instalaciones de escritorios fijos. Para evitar el robo y la manipulación indebida del dispositivo, el gabinete de la estación de carga está...
3. Identificación de Partes y Características CSD32USB Puertas Divididas con Cerradura Repisas de Almacenamiento (Soportan hasta 16 Dispositivos Cada Una.) Unidad Cargadora / Hub USB de 32 Puertos Orificios de Acceso para Cable de Alimentación con Clavija 5-15P en Ángulo Recto (1 Abertura Ubicada en Cada Lado.)
4. Instalación ¡Precaución! ¡Lea todas las instrucciones y las advertencias antes de realizar la instalación! Advertencia: las estaciones de carga pueden ser muy pesadas. No intente desempacar ni instalar la estación de carga sin ayuda. Antes de proceder con la instalación, siga las instrucciones de desempaque incluidas en el documento que se envía junto con el producto. Tenga mucho cuidado al manipular la estación de carga y asegúrese de seguir todas las instrucciones de manejo e instalación. No intente instalar el equipo sin antes estabilizar la estación de carga. 4.1 Alimentación de la Unidad de Cargador/Hub USB Para conexiones de alimentación convenientes, se encuentra una pestaña a cada lado de los orificios de acceso del cable de alimentación.
USB al smartphone por cargar. Repita para todos los dispositivos. Tripp Lite ofrece cables individuales y en paquetes de 10 para dispositivos Apple que usan cables USB a 30 Pines o USB a Lightning™, así como cables ®...
6. Instalación en Pared Para realizar la instalación en pared, necesitará: PANEL SUPERIOR • Nivel 406 mm 16” • Herramientas adecuadas para la instalación en pared [16 pulg.] • Accesorios adecuados para la instalación en pared (no se incluyen) Advertencia: no intente instalar la estación de carga a la pared con 305 mm 12”...
7. Colocación en Escritorio/Piso 355.63 mm 355.63 mm PANEL PANEL [14 pulg.] [14 pulg.] INFERIOR SUPERIOR 50.8 mm 50.8 mm PANEL PANEL [2 pulg.] [2 pulg.] FRONTAL FRONTAL 17.56 mm 457.2 mm 17.56 mm 457.2 mm [2 13/16 pulg.] [18 pulg.] [2 13/16 pulg.] [18 pulg.] ADVERTENCIA: Para aplicaciones en escritorio y piso, instale siempre una...
2 x USB Mini (Hembra) Velocidad de Transmisión USB 2.0: Hasta 480 Mbps Requerimiento de Energía Entrada: 110-120V, 8A, 50/60 Hz (CSD32USB) or 230V, 5A, 50 Hz (CSDXB32USB, CSDXS32USB) Salida: 5.0V, 2.4A Max (por puerto USB) Temperatura de Operación 0° a 30° C / 32° a 86° F Humedad de Funcionamiento 5 a 95% de HR, Sin Condensación...
El servicio técnico bajo esta garantía solo puede ser obtenido si usted entrega o envía el producto (con todos los cargos de envío o entrega prepagos) a: Tripp Lite; 1111 W. 35th Street; Chicago IL 60609; EE. UU. El vendedor abonará los cargos de envío de devolución.
1. Importantes consignes de sécurité CONSERVEZ CES INSTRUCTIONS Ce manuel contient des instructions et des avertissements devant être suivis pour l'installation et l'utilisation du produit décrit dans ce manuel. Le non-respect de ces instructions peut entraîner l'annulation de la garantie et occasionner des dommages matériels ou corporels. Chargeur/concentrateur USB : •...
2. Vue d'ensemble Votre station de charge est une solution tout-en-un pour stocker, charger et synchroniser jusqu'à 32 smartphones. Votre station de charge peut être montée de manière pratique sur un mur ou être utilisée pour des installations fixes sur un bureau. Pour éviter le vol et l'altération de l'appareil, le boîtier de votre station de charge est équipé...
Étagères de rangement (capacité de 16 appareils chacune) Chargeur/concentrateur USB 32 ports Trous d'accès au cordon d'alimentation avec fiche 5-15P (CSD32USB) à angle droit (1 ouverture de chaque côté). Verrou à 3 points Moraillon à cadenas (en option assemblage requis, voir Section 3.4 pour plus d'informations. Verrou non fourni.) Panneau arrière avec fentes de montage mural en forme de trou de serrure (voir Section 6 pour plus d'informations).
4. Configuration Attention ! Lisez toutes les instructions et tous les avertissements avant de commencer l'installation ! Avertissement : les stations de charge peuvent être très lourdes. N'essayez pas de déballer ou de monter la station de charge sans assistance. Soyez extrêmement prudent lors de la manutention de la station de charge et veillez à...
USB au smartphone qui doit être chargé. Faites la même chose pour les autres appareils. Tripp Lite propose des câbles individuels et des lots de 10 câbles pour les appareils Apple ® nécessitant des câbles USB vers 30 broches ou USB vers Lightning™, ainsi que des câbles individuels et des lots de 10 câbles pour les appareils USB 3.0 ou 2.0 nécessitant des...
6. Montage mural Pour le montage mural, vous aurez besoin de ce qui suit : HAUT • Niveau 16” • Outils appropriés pour le montage mural • Quincaillerie adaptée pour le montage mural (non fournie) Avertissement : ne pas tenter de fixer la station de charge au mur avec des appareils électroniques personnels à...
7. Placement sur un bureau 355,6 mm 355,6 mm HAUT 14" 14" 50,8 mm 50,8 mm 2" 2" AVANT AVANT 17,56 mm 457,2 mm 17,56 mm 457,2 mm 2 13/16" 18" 2 13/16" 18" AVERTISSEMENT : pour les applications de bureau, installez toujours la station de charge dans un endroit structurellement sain avec une surface plane capable de supporter le poids de la station de charge, de tous les équipements qui seront installés dans la station de charge et de tous les autres racks et/ou équipements qui seront installés à...
Vitesse de transmission USB 2.0 : jusqu'à 480 Mbits/s Alimentation requise Entrée : 110-120 V, 8 A, 50/60 Hz (CSD32USB) ou 230 V, 5 A, 50 Hz (CSDXB32USB, CSDXS32USB) Sortie : 5,0 V, 2,4 A max. (par port USB) Température de fonctionnement 0 à...
Numéro d'identification de conformité aux règlements Pour des raisons d'identification et de conformité aux règles de certification, un numéro de série unique a été attribué à votre produit Tripp Lite. Le numéro de série est indiqué sur l'étiquette de la plaque signalétique du produit, où...
1. Важные указания по технике безопасности СОХРАНИТЕ НАСТОЯЩИЕ УКАЗАНИЯ В настоящем руководстве содержатся указания и предупреждения, которые необходимо соблюдать в процессе установки и эксплуатации описанного в нем изделия. Несоблюдение этих указаний и предупреждений может привести к аннулированию гарантии и причинить материальный ущерб...
2. Краткое описание Приобретенная вами зарядная станция представляет собой универсальное устройство для хранения, зарядки и синхронизации устройств в количестве до 32 шт. Зарядная станция может удобно монтироваться на стены, а также приспосабливаться для стационарного размещения на столе. Во избежание хищения устройств или несанкционированного доступа к ним корпус вашей зарядной станции оснащен запирающимися стальными дверцами.
Полки для хранения (вмещают до 16 устройств каждая). 32-портовое зарядное устройство USB / USB-концентратор Отверстия для шнура питания с прямоугольным разъемом 5-15P (CSD32USB) (по 1 отверстию с каждой стороны). 3-точечный замок Петля для навесного замка (опционально, требуется сборка. Подробнее см. в Разделе 3.4. Замок в комплект поставки не входит).
4. Начальная установка Внимание! Перед установкой внимательно ознакомьтесь со всеми указаниями и предупреждениями! Внимание! Зарядные станции могут быть крайне тяжеловесными. Не пытайтесь распаковывать или монтировать зарядную станцию в одиночку. Будьте предельно осторожны при перемещении зарядной станции и обязательно следуйте всем указаниям по обращению и установке. Не производите установку оборудования в зарядную станцию до...
Подключите кабель USB, приобретенный отдельно или поставляемый производителем устройства, к заряжаемому смартфону. Повторите перечисленные действия для всех устройств. Компания Tripp Lite предлагает отдельно и в упаковках по 10 шт. кабели для подключения устройств марки Apple®, использующих кабели с USB- и 30-контактными разъемами или разъемами USB и...
6. Настенный монтаж Для настенного монтажа потребуются: ВЕРХ • Уровень 16” • Инструменты для настенного монтажа • Оснастка для настенного монтажа (в комплект поставки не входит) Внимание! Не пытайтесь крепить зарядную станцию с установленными в ней персональными электронными устройствами. 12” На...
7. Настольное размещение ВЕРХ НИЗ 355,6 мм 355,6 мм ЛИЦЕВАЯ ЛИЦЕВАЯ 50,8 мм 50,8 мм СТОРОНА СТОРОНА 17,56 мм 457,2 мм 17,56 мм 457,2 мм ВНИМАНИЕ! При настольном монтаже зарядная станция обязательно должна устанавливаться в конструкционно прочном месте с ровным основанием, способным выдерживать вес самой зарядной...
Скорость передачи данных USB 2.0: до 480 Мбит/с Требования к электропитанию Вход: 110-120 В, 8 А, 50/60 Гц (CSD32USB) или 230 В, 5 А, 50 Гц (CSDXB32USB, CSDXS32USB) Выход: не более 5,0 В, 2,4 А (на каждый порт USB) Диапaзoн рабочих температур...
Идентификационные номера соответствия нормативным требованиям В целях сертификации на соответствие нормативным требованиям и опознавания приобретенному вами изделию марки Tripp Lite присвоен уникальный серийный номер. Серийный номер располагается на заводской табличке вместе со всеми необходимыми отметками о приемке и прочей информацией. При запросе информации о соответствии данного изделия нормативным требованиям обязательно указывайте его серийный номер.
1. Wichtige Sicherheitshinweise BITTE BEWAHREN SIE DIESE ANLEITUNG AUF Diese Betriebsanleitung enthält Anweisungen und Warnhinweise, die bei Installation und Betrieb des hierin beschriebenen Produkts befolgt werden müssen. Die Nichtbeachtung kann zum Erlöschen von Gewährleistungs-/Garantieansprüchen führen und Sachschäden bzw. Verletzungen verursachen. USB-Ladegerät/Netzknoten: •...
2. Überblick Ihre Ladestation ist eine Rundum-Lösung zum Aufbewahren, Aufladen und Synchronisieren von bis zu 32 Smartphones. Ihre Ladestation kann sowohl an der Wand als auch stationär auf dem Schreibtisch aufgestellt werden. Zum Schutz vor Diebstahl oder unbefugtem Zugriff verfügt das Gehäuse Ihrer Ladestation über verschließbare Stahltüren. Ein Vorhängeschloss (optional), das an den Türen angebracht wird, sorgt für zusätzlichen Schutz.
Verriegelbare geteilte Türen Aufbewahrungsregale (Tragen jeweils bis zu 16 Geräten.) 32-Port USB-Ladegerät/Hub-Einheit Öffnungen für Netzkabel mit rechtwinkligem 5-15P (CSD32USB) Stecker (1 Öffnung auf jeder Seite). 3-Punkt-Verriegelung Vorhängeschloss-Haspe (Optional. Erforderliche Montage, siehe Abschnitt 3.4 für weitere Informationen. Schloss nicht im Lieferumfang enthalten.) Rückwand mit Schlüssellochschlitzen für die Wandmontage (Siehe Abschnitt 6 für weitere Informationen).
4. Einrichten Achtung! Lesen Sie vor der Installation sämtliche Anleitungen und Warnhinweise durch! Achtung: Ladestationen können sehr schwer sein. Versuchen Sie nicht, die Ladestation ohne fremde Hilfe auszupacken oder zu montieren. Lassen Sie beim Umgang mit der Ladestation äußerste Vorsicht walten und befolgen Sie unbedingt sämtliche Anweisungen zu Umgang und Installation.
Gerätehersteller gelieferten abgeschirmten USB-Kabel an das zu ladende Smartphone an. Wiederholen Sie den Vorgang für sämtliche Geräte. Tripp Lite bietet einzelne Kabel und 10er-Packs für Apple-Geräte mit USB-auf-30-Pin- oder USB-auf-Lightning™-Kabeln sowie einzelne Kabel und 10er-Packs für USB-3.0- oder 2.0-Geräte mit USB-A-auf-5-Pin-Micro-B-Kabeln (Stecker).
6. Wandmontage Für die Wandmontage benötigen Sie: OBEN • Wasserwaage 16” • Passende Werkzeuge für die Wandmontage • Passende Eisenwaren für die Wandmontage (nicht im Lieferumfang enthalten) Warnung: Versuchen Sie nicht, die Ladestation an der Wand zu befestigen, wenn sich persönliche elektronische Geräte darin befinden. 12”...
7. Desktop-Platzierung 14” 14” OBEN UNTEN 355,6 mm 355,6 mm 2” 2” 50,8 mm 50,8 mm VORDERSEITE VORDERSEITE 2 13/16” 18” 2 13/16” 18” 17,56 mm 457,2 mm 17,56 mm 457,2 mm WARNUNG: Installieren Sie die Ladestation bei Desktop-Anwendungen immer in einem statisch einwandfreien Bereich mit einer ebenen Fläche, die das Gewicht der Ladestation, aller in der Ladestation installierten Geräte und aller anderen in der Nähe installierten Gehäuse und/oder Geräte tragen kann.
2 x USB-Mini (Buchse) Übertragungsgeschwindigkeit USB 2.0: bis zu 480 Mbit/s Strombedarf Eingang: 110-120 V, 8 A, 50/60 Hz (CSD32USB) oder 230 V, 5 A, 50 Hz (CSDXB32USB, CSDXS32USB) Ausgang: 5,0 V, 2,4 A Max. (pro USB-Anschluss) Betriebstemperatur 0 °C bis 30 °C...
• Schließen Sie das Gerät an eine Steckdose an, die zu einem anderen Stromkreis gehört als die mit dem Empfänger verbundene Steckdose. • Wenden Sie sich an den Händler oder einen erfahrenen Radio-/Fernsehtechniker, um Hilfe zu erhalten. Änderungen oder Modifikationen an diesem Gerät, die nicht ausdrücklich von Tripp Lite genehmigt wurden, können die Berechtigung des Benutzers zum Betreiben dieses Geräts aufheben.
Need help?
Do you have a question about the CSD32USB and is the answer not in the manual?
Questions and answers