Advertisement
Quick Links
Striping Kit
2014 or 2015 GrandStand
Model No. 131-1470
Note: Determine the left and right sides of the machine from the normal operating position.
This product contains a chemical or chemicals known to the State of California to
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
1
Preparing the Mower
No Parts Required
Procedure
1. Park the machine on a level surface.
2. Engage the parking brake.
3. Shut off the engine and remove the key.
4. Thoroughly clean the mower deck. Remove all debris
to ensure that the kit will fit properly.
© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Description
No parts required
Mounting bracket
Carriage bolt (3/8 x 1 inch)
Flange nut (3/8 inch)
Spring
Clevis pin
Hairpin cotter
No parts required
Register at www.Toro.com.
®
Mowers
WARNING
CALIFORNIA
Qty.
–
2
2
2
2
2
2
–
5. Repair all bent or damaged areas and replace any
missing parts.
6. Raise the platform and verify the latch is securely
engaged to hold the platform up.
Form No. 3385-772 Rev B
Installation Instructions
Use
Prepare the mower.
Install the mounting brackets.
Install the roller assembly to striper
bracket mounts.
Connect the chains.
Original Instructions (EN)
All Rights Reserved *3385-772* B
Printed in the USA
Advertisement
Related Manuals for Toro 131-1470
Summary of Contents for Toro 131-1470
- Page 1 Form No. 3385-772 Rev B Striping Kit 2014 or 2015 GrandStand ® Mowers Model No. 131-1470 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
- Page 2 Installing the Mounting Brackets Parts needed for this procedure: Mounting bracket g026595 g026595 Carriage bolt (3/8 x 1 inch) Figure 2 Flange nut (3/8 inch) Shown with narrow base mower 1. Flange nut (3/8 inch) 3. Carriage bolt (3/8 x 1 inch) Procedure 2.
- Page 3 G026602 g026602 Figure 3 1. Left-spring long finger 4. Hairpin-cotter 2. Clevis pin 5. Roller assembly 3. Right-spring long finger g026656 g026656 Figure 5 2. Position the roller assembly into the striper mounting brackets (Figure 1. Top of the roller assembly 3.
- Page 4 g011307 Figure 6 1. Left lift handle 3. Right lift handle 4. Roller 2. Platform down 3. Snap the chain end into the hole in the lower front side plate of the platform. Repeat for the opposite side (Figure g010976 Figure 7 1.
-
Page 5: Operation
Operation • Stiff grass where wheel tracks are less visible will usually produce poor striping. • Cool season grass types found in northern areas are Raising the Roller usually good for striping. With the platform down, raise the roller up and rotate the lift •... - Page 6 Driving the machine to different cutting • Bagging can display heavy wheel tracks, reducing the effect of striping. areas • Mulching will often display excellent contrast, enhancing • Raise the roller and the deck and drive along a previous the effect of striping. cut path to transport from one area of the property to another section.
- Page 7 Notes:...
Need help?
Do you have a question about the 131-1470 and is the answer not in the manual?
Questions and answers