Advertisement
Quick Links
48in or 52in Recycler
Model No. 139-6650
Model No. 139-6653
Important:
This kit does not come with the recycler blades.
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
10
11
© 2021—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
Discharge plate
Carriage bolt (3/8 x 1-1/4 inches)
Carriage bolt (5/16 x 7/8 inch)
Flange nut (small flange) (3/8 inch)
Flange nut (5/16 inch)
Left baffle
Center baffle
Right baffle
Small flange nut (3/8 inch)
Carriage bolt (3/8 x 1 inch)
Bolt (3/8 x 1 inch)
Large flange nut (3/8 inch)
Left baffle
Center baffle
Right baffle
Flange nut (small flange) (3/8 inch)
Carriage bolt (3/8 x 1 inch)
Bolt (3/8 x 1 inch)
Flange nut (large flange) (3/8 inch)
No parts required
Recycler blade (sold separately)
Register at www.Toro.com.
®
Kit
Qty.
Raise the mower for access
–
(GrandStand mowers only).
–
Prepare the machine.
Remove the existing baffles (for mower
–
decks with existing baffles).
Remove the deck fasteners and
–
discharge baffle (for Z Master 4000
mower deck).
–
Remove the existing discharge chute.
–
Drill holes (for G3 mower decks).
1
2
1
Install the discharge plate.
2
1
1
1
1
Install the baffles (for 48-inch mower
7
decks).
7
2
2
1
1
1
Install the baffles (for 52-inch mower
8
decks).
7
2
1
–
Tighten all the fasteners.
3
Install the recycler blades.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Form No. 3447-971 Rev A
Installation Instructions
Use
*3447-971*
Advertisement
Related Manuals for Toro 139-6650
Summary of Contents for Toro 139-6650
- Page 1 Form No. 3447-971 Rev A 48in or 52in Recycler ® Model No. 139-6650 Model No. 139-6653 Installation Instructions Important: This kit does not come with the recycler blades. Loose Parts Use the chart below to verify that all parts have been shipped.
- Page 2 Raising the Mower for Access GrandStand Mowers Only No Parts Required Procedure You can raise the front of the mower and support to access under the machine for maintenance. WARNING g009434 The machine could fall onto someone and Figure 1 cause serious injury or death.
-
Page 3: Preparing The Machine
Preparing the Machine No Parts Required Procedure Disengage the PTO, move the motion-control levers to the N position, and engage the EUTRAL LOCK parking brake. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. - Page 4 g309912 Figure 3 1. Discharge baffle...
- Page 5 Removing the Deck Fasteners and Discharge Baffle For Z Master 4000 Mower Decks No Parts Required Procedure Remove the 6 carriage bolts (3/8 x 7/8 inch), 6 locknuts (3/8 inch), and discharge baffle from the mower deck (Figure After removing the discharge baffle, install the 2 carriage bolts (3/8 x 7/8 inch) and 2 locknuts (3/8 inch) back into the mower deck (Figure Retain the fasteners and discharge baffle for converting back to side discharge.
-
Page 6: Drilling Holes
Removing the Existing Drilling Holes Discharge Chute For G3 Mower Decks No Parts Required No Parts Required Procedure Procedure Remove the locknut, bolt, spring, and spacer Check the hole diameters in the locations shown holding the deflector to the pivot brackets Figure (Figure If there are no holes in the side discharge... - Page 7 Installing the Discharge Plate Parts needed for this procedure: Discharge plate Carriage bolt (3/8 x 1-1/4 inches) Carriage bolt (5/16 x 7/8 inch) Flange nut (small flange) (3/8 inch) Flange nut (5/16 inch) Procedure Install the discharge plate to the outside of the mounting bracket with 2 carriage bolts (3/8 x 1-1/4 inches) and 2 flange nuts (small flange) (3/8 inch) as shown in...
- Page 8 Loosely install the right baffle to the discharge plate with 1 carriage bolt (3/8 x 1 inch) and a small flange nut (3/8 inch) as shown in Figure Loosely install the right baffle to the top of the Installing the Baffles mower deck with 1 carriage bolt (3/8 x 1 inch) and 1 large flange nut (3/8 inch) as shown in Figure...
- Page 9 Position the center baffle into the mower. Loosely install the center baffle to the left baffle with 1 carriage bolt (3/8 x 1 inch) and 1 flange nut (small flange) (3/8 inch) as shown in Figure Refer to Figure 9 for the position of the baffles.
- Page 10 Loosely install the right baffle to the discharge plate with 1 carriage bolt (3/8 x 1 inch) and a flange nut (small flange) (3/8 inch) as shown in Figure Installing the Baffles Loosely install the right baffle to the top of the mower deck with 1 carriage bolt (3/8 x 1 inch) and 1 flange nut (large flange), (3/8 inch) as For 52-inch Mower Decks...
- Page 11 Loosely install the center baffle to the top of 1 flange nut (small flange) (3/8 inch) as shown the mower deck with 1 bolt (3/8 x 1 inch) and Figure g010836 Figure 12 GrandStand mower deck shown 1. Right baffle 4.