Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper 84746
Summary of Contents for Draper 84746
- Page 1 Version 4 May 2023 230V PATIO WEED SWEEPER 84746...
-
Page 2: Copyright © Notice
All photographs and drawings within this manual are document is part of the product; retain it for the life supplied by Draper Tools to help illustrate correct of the product, passing it on to subsequent holders. operation of the product. -
Page 3: Table Of Contents
2. Contents 1. Preface 1.1 Product Reference 1.2 Revisions 1.3 Understanding the Safety Content of This Manual 1.4 Copyright © Notice 2. Contents 3. Product Introduction 3.1 Intended Use 3.2 Specification 4. Health and Safety Information 4.1 General Health and Safety Precautions 4.2 Additional Precautions for this Patio Sweeper 5 4.3 Connection to the Power Supply 4.4 Residual Risk 5. -
Page 4: Product Introduction
Read this manual in full before attempting to assemble, will be considered misuse. Draper Tools accepts no operate or maintain the product, and retain it for later responsibility for improper use of this product. -
Page 5: Health And Safety Information
• If the supply cord is damaged, it must be replaced • ALWAYS keep the brush attachment clear or the work with a special cable available from Draper Tools or its surface and surrounding objects during start-up. authorised service agent. • Keep hands, feet and loose clothing well away from • NEVER pull on the power cable to disconnect the plug... -
Page 6: Connection To The Power Supply
• If the product vibrates abnormally during use, Important: This product MUST be used with a residual immediately stop the machine, allow it to cool and current device (RCD), e.g. Draper Stock Nos. 69307 or investigate the cause. 89301. ALWAYS read the manufacturer instructions for −... -
Page 7: Identification And Unpacking
5. Identification and Unpacking 5.1 Product Overview (10) Auxiliary handle Power cable and plug Brush attachment Safety lock Brush guard (10) Trigger switch Cable strain relief clamp Cable strain relief loop Guide wheel Main handle – 7 –... -
Page 8: What's In The Box
Carefully remove the product from the packaging and damaged or missing, do not attempt to use the product. examine it for any signs of damage that may have Please contact the Draper Helpline; contact details can occurred during shipment. be found at the back of this manual. -
Page 9: Assembly Instructions
6. Assembly Instructions Important: Before attempting to assemble or use this 3. Align the brush guard with the holes around the product, read and understand all the safety instructions brush axle (12) and secure it in place with the two listed in this manual. - Page 10 6. Assembly Instructions 5. Insert the pin tool (J) into the hole (14) in the brush axle and place the M8 nut (H) onto the end of the brush axle. 6. Using the pin tool to lock the axle, use the M8 spanner (I) to tighten the nut into place.
-
Page 11: Operating Instructions
7. Operating Instructions 7.1 Operation 4. Slowly and carefully lower the machine into a joint in the surface until the brush contacts the material and WARNING! Ensure that the brush attachment is the guide wheel (6) rests on the surface. in good condition and is securely and soundly 5. -
Page 12: Notes On Use
− The steel brush (E) is suitable for robust surfaces and stubborn weeds. − Draper Tools recommends that the nylon brush (D) is used for light vegetation and where the surface may be too sensitive for the steel brush. -
Page 13: Maintenance And Storage
• Store the product in temperatures between 5–30°C regular care will help to ensure a longer lifespan for the where there is no risk of frost. product. Draper Tools recommends cleaning the product immediately after each use. • Keep all switches and air vents clean and free from dust and debris as far as possible. -
Page 14: Spares, Returns And Disposal
Draper Tools Product Helpline for details of your nearest authorised agent. Draper Tools will endeavour to hold any spare parts, if applicable, for seven years from the date that it sells the final matching stock item. -
Page 15: Warranty
This warranty period covers parts and labour for 12 months from the date of Your Draper Tools guarantee is not effective until you can purchase. Where tools have been hired out, the warranty produce, upon request, a dated receipt or invoice to period covers 90 days from the date of purchase. -
Page 16: Explanation Of Symbols
11. Explanation of Symbols Class II construction Read the instruction manual (Double insulated) Wear suitable protective goggles Rated input 1200 No load speed Wear ear defenders Power cable length Wear protective gloves approved Wear protective footwear Continuous A-weighted sound power level WEEE –... -
Page 17: Notes
Notes – 17 –... - Page 18 Notes – 18 –...
- Page 19 Notes – 19 –...
- Page 20 Telephone Sales Desk: +44 (0) 23 8049 4333 General Enquiries: +44 (0) 23 8026 6355 General Fax: +44 (0) 23 8026 0784 Please contact the Draper Tools Product Helpline for repair and servicing enquiries. © Published by Draper Tools Limited © Published by Draper Tools Limited...
Need help?
Do you have a question about the 84746 and is the answer not in the manual?
Questions and answers