JUKI PS-910 Instruction Manual
  1. Manuals
  2. Brands
  3. JUKI Manuals
  4. Sewing Machine
  5. PS-910
  6. Instruction manual
JUKI PS-910 Instruction Manual

JUKI PS-910 Instruction Manual

Barcode reader
Hide thumbs Also See for PS-910:

Advertisement

Table of Contents

PS-910
Barcode reader
INSTRUCTION MANUAL
CAUTION :
This Instruction Manual describes the barcode reader. When you want to use your sewing ma-
chine with this product attached, refer to the "Safety precautions" in the Instruction Manual for
your sewing machine carefully until you fully understand the included precautions in prior.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PS-910 and is the answer not in the manual?

Questions and answers

Related Manuals for JUKI PS-910

Summary of Contents for JUKI PS-910

  • Page 1 PS-910 Barcode reader INSTRUCTION MANUAL CAUTION : This Instruction Manual describes the barcode reader. When you want to use your sewing ma- chine with this product attached, refer to the “Safety precautions” in the Instruction Manual for your sewing machine carefully until you fully understand the included precautions in prior.

  • Page 2: Table Of Contents

    CONTENTS 1. Installing the parts ........................1 2. Setting the barcode functions ....................5 2-1. Setting the barcode functions on the operation panel ...............5 2-2. Setting the barcode number ......................7 2-3. Cancelling the barcode number ....................8 2-4. How to use the barcode reader.....................8...

  • Page 3: Installing The Parts

    1. Installing the parts WARNING : Be sure to turn OFF the power supply and air supply to the sewing machine before attaching the parts in order to protect against accidents caused by an unintended start of the sewing machine. No.
  • Page 4 2) Remove the panel mounting plate fixing screws ❽ and ❾ , and fix the barcode reader mounting ❽ ❽ plate ❶ and the panel mounting plate with the screws ❷ . ❾ ❾ ❷ ❷ 3) Connect the barcode reader plug to the connector at the panel as shown. – 2 –...
  • Page 5 4) Pass the cable clip band ❼ through this hole in the barcode reader mounting plate and fix the cable behind the panel. ❷ ❷ ❼ ❼ Cut the excess cable clip band. 5) The installation is complete after attaching the panel mounting plate in its original position. –...
  • Page 6 ❺ ❺ provided. 6) Take out a seal from barcode seals One hundred barcode seals (with serial numbers from 001 to 100) are provided. ❺ ❺ 13090： [13090] Stick the barcode seal 100 mm to the right side from the center of the cassette (setup guide) and 30 mm from the upper side of the cassette.

  • Page 7: Setting The Barcode Functions

    2. Setting the barcode functions 2-1. Setting the barcode functions on the operation panel 1) Press button A. 2) Press button B. In the default state, the factory-set password is provided. The password is "11111111". 3) Press button C. 4) To allow the barcode reader to recognize the template, change D from "Electronic identification label"...
  • Page 8 5) Return to the screen of 2). Press button E. 6) Press button F. 7) Press button G. The password is "11111111". 8) Set the mode to "0". – 6 –...

  • Page 9: Setting The Barcode Number

    2-2. Setting the barcode number 1) Press button A. 2) Press button B. 3) Select the sewing pattern file you want to read and press button C. 4) Press button D. Save the data. – 7 –...

  • Page 10: Cancelling The Barcode Number

    2-3. Cancelling the barcode number When you want to cancel the barcode reader number, it is necessary to set the current number to the largest value (the largest one of unassigned numbers, such as 100) first. Then, change that number to "0". Example) When the number "3" is changed to "0", the subse- quent numbers registered "4, 5 and 6" will also be ↓...

Table of Contents