1. Manuals
  2. Brands
  3. Omron Manuals
  4. Network Hardware
  5. ITBC-CST01 - 09-2000
  6. Operation manual

Omron ITBC-CST01 - 09-2000 Operation Manual

Cs1 bus interface board
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ITBC-CST01
CS1 Bus Interface Board
Operation Manual
Produced September 2000

Advertisement

Table of Contents
loading

Related Manuals for Omron ITBC-CST01 - 09-2000

Summary of Contents for Omron ITBC-CST01 - 09-2000

  • Page 1 ITBC-CST01 CS1 Bus Interface Board Operation Manual Produced September 2000...
  • Page 2 1, 2, 3... 1. Indicates lists of one sort or another, such as procedures, checklists, etc.  OMRON, 2000 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permis- sion of OMRON.

  • Page 3: Table Of Contents

    ........... . . Mounting the CS1 Bus Interface Board .
  • Page 4 This manual describes the installation and operation of the ITBC-CST01 CS1 Bus Interface Board and includes the sections described below. The CS1 Bus Interface Board is installed in a personal computer to connect the computer to a CS1-series PC via the CS1 bus.
  • Page 5 This section provides general precautions for using the CS1 Bus Interface Board and related devices. The information contained in this section is important for the safe and reliable application of the CS1 Bus Interface Boards. You must read this section and understand the information contained before attempting to set up or operate a CS1 Bus Interface Board.

  • Page 6: Intended Audience

    Safety Precautions WARNING Do not attempt to take a CS1 Bus Interface Board apart while the power is being supplied. Doing so may result in electric shock. WARNING Fail-safe measures must be taken by the customer to ensure safety in the event of incorrect, missing, or abnormal signals caused by broken signal lines, momentary power interruptions, or other causes.

  • Page 7: Application Precautions

    Insufficient safety measures against short-circuiting may result in burning. • Always turn OFF the power supply to the CS1 Bus Interface Board and the PLC before attempting any of the following. Not turning OFF the power supply may result in malfunction or electric shock.
  • Page 8 • Check the user program for proper execution before actually executing it. Not checking the program may result in unexpected operation. • Do not pull on cables or bend them past their natural bending radius. Doing so may damage the cables and interfere with proper operation.

  • Page 9: Introduction

    SECTION 1 Introduction This section describes the functions and configuration of the CS1 Bus Interface Board. Functions ............. .

  • Page 10: Functions

    4. The computer cannot be connected to a C200H Rack. 1-1-2 Precautions for System Design • The PC will not start operation even after the power supply is turned ON until the CS1 Bus Interface Board completes initialization. The time required for ini- tialization depends on the computer in which the Board is installed, You must design the system to allow for this delay.

  • Page 11: Products

    Safety Precautions Safety Precautions The ITBC-CNjjj-CST is shown below. Use the illustration to confirm you have the correct model. The cable length varies with the model as listed in the following table. Model Length ITBC-CN001-CST...

  • Page 12: Hardware Settings

    SECTION 2 Hardware Settings This section describes the hardware settings required to used the CS1 Bus Interface Board. Nomenclature and Functions ..........

  • Page 13: Nomenclature And Functions

    Note Refer to 1-1 Functions for details on CPU Bus Units. Set the Unit number to between 0 and F (i.e., 0 and 15). Check that the Unit num- ber is not used by any other CPU Bus Unit, such as an Ethernet Unit or Controller Link Unit.

  • Page 14: Mounting The Cs1 Bus Interface Board

    I/O Connecting Cable Section Mounting the CS1 Bus Interface Board Mount the CS1 Bus Interface Board to a PCI bus connector in the personal com- puter. Note Turn OFF the power supply to the personal computer before starting the proce- dure to mount the Board.

  • Page 15: A Specifications

    Appendix A Specifications This appendix lists the specifications of the CS1 Bus Interface Unit. Other specifications confirm to those of the SYSMAC CS1-series PCs. Item Specifications Model ITBC-CST01 Current consumption 0.2 A max. Weight 0.1 kg max. Power supply voltage 4.875 to 5.25 VDC...

  • Page 16: B Dimensions

    Appendix B Dimensions The dimensions of the CS1 Bus Interface Board are shown below. All dimensions are in millimeters.

  • Page 17: Revision History

    Revision History A manual revision code appears as a suffix to the catalog number on the front cover of the manual. Cat. No. V211-E1-1 Revision code The following table outlines the changes made to the manual during each revision. Page numbers refer to the previous version.

Table of Contents