Subscribe to Our Youtube Channel
Related Manuals for Hyundai power products HTRT4140-1
Summary of Contents for Hyundai power products HTRT4140-1
- Page 1 PETROL CHAINSAW HTRT4140-1 WARNING: Read thoroughly the instruction manual before use.
-
Page 2: Table Of Contents
CONTENTS 1. SAFETY INSTRUCTIONS........................3 2. YOUR PRODUCT........................... 8 3. ASSEMBLY............................. 9 4. FILLING THE FUEL TANK......................... 10 5. OPERATION............................11 6. MAINTENANCE AND STORAGE..................... 16 7. DECLARATION OF CONFORMITY....................19 8. WARRANTY............................20 9. PRODUCT FAILURE........................... 21 10. WARRANTY EXCLUSIONS......................22... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS WARNING! When using this type of tool, basic precautions should always be followed to reduce the risk of fire, electric shock and injury. Read all instructions carefully before attempting to use this product and retain these instructions. - Page 4 Do not lean. Keep a good seating and balance at all times. To maintain tools and accessories carefully, keep cutting tools sharp and clean for better and safer performance. Follow the instructions in this manual to lubricate and change accessories. ...
- Page 5 necessary. Do not place any part of the body on the chain when the chainsaw is operating. Before starting the chain saw, make sure that the chain is not in contact with anything. A moment of inattention during use may cause your clothing or body part to stick to the chain. ...
- Page 6 Never store the tool and the fuel tray indoors where there is a naked flame, such as near a water heater. If fuel has spilled, do not attempt to start the machine, but rather move it away from the spill before starting to use it.
- Page 7 There is risk of injury and property damage due to attachments or broken the sudden impact of hidden objects when using cutting. Risk of injury to persons and property caused by flying objects. Prolonged use of this product exposes the operator to vibration and can produce so-called "white finger"...
-
Page 8: Your Product
9- Chain adjusting tension 4- Front handle 10-Stud bar 5- Front hand guard/Chain brake 11-Chain guide 6- Saw Chain b. Technical data Model HTRT4140-1 Type of engine RY1E40F Fuel Tank Volume 260cm³ Oil tank volume 210cm³ Idle speed of the engine 3100±300/min... -
Page 9: Assembly
Carburetor MC16C4-1/HLIC MC1606B/HUAYI 1E40F/JINKE WT994/Walbro MP16-1/YINBA Spark plug L8RTF/LD NHSP, L8RTC/TORCH, L8RTF/BOSCH, L8RTC/CDK, BPMR7A/NGK, L8RTF/Torch Sound pressure level LpA,eq: 98.8 dB(A) k=3 dB(A) Sound power level LwA,eq: 107.8 dB(A) k=3 dB(A) Guaranteed power level LwA : 114dB(A) (2000/14/EC) Value of vibration A front_hv,eq: 6,5 m/s², K=1.5 m/s²... -
Page 10: Filling The Fuel Tank
4. FILLING THE FUEL TANK AND OIL TANK 1) Filling fuel tank WARNING: When filling the tank: The chainsaw must always be stopped and cooled. Never smoke during refueling. It must not have flames or sparks near the fuel. Before refueling, allow the chainsaw to cool completely. Do not attempt to refuel when the engine is hot. -
Page 11: Operation
c. Storage of fuel The fuel must be kept in a clean and safe container and always closed. If you are not using the product for a long time, remove the fuel mixture and add it to a container. Do not leave the fuel for a long time in the product. The fuel may clog the carburetor and the engine will not operate properly. - Page 12 Set the switch to position I. Push the fuel pump several times (around 10 times). Pull the choke lever. It will close and the throttle will be moved to the starting position. Hold the chainsaw firmly against the ground. Put the chainsaw: ...
- Page 13 Push lightly the lock throttle (1) and then the accelerator throttle to start working. b. Stopping the engine Allow the chainsaw to run for a few minutes. Then turn the switch to the OFF position. 1. Main settings a. Adjusting the carburetor The carburetor is preset at the factory.
- Page 14 c. Release of the chain brake To use the chain saw again, the chain brake must be released. This must be done machine off and cooled. Pull the shield until it returns to its original position. d. Sharpening of the chain For best performance, we strongly recommend that you periodically sharpen the chain.
- Page 15 When the tree falls, shout or make a beep to alert people in the vicinity. When the shaft falls, you must move away from the cutting area. b. Trunk on the ground Cut half of the trunk, turn it over and finish the cut on the other side. c.
-
Page 16: Maintenance And Storage
6. MAINTENANCE AND STORAGE 1. Maintenance Before any maintenance work, the machine must be switched off and completely cooled. Perform the maintenance work according to the instructions below and perform them regularly. A clean, well-maintained machine increases its standard of living and efficiency. - Page 17 e. Guide bar Cleaning: Remove bar guide to remove dirt from grooves and oil inlet. Regularly grease the pinion. Check: Reverse the bar from time to time to avoid the effects of wear. The bar rail should always be in place. Use a ruler to observe it. If a gap is observed between them, then the rail is normal. Otherwise, the rail is worn out.
- Page 18 h. chain saw Check each time the cutter and cutting angles are as shown below. i. Sharpening of the chain For best performance, we strongly recommend that you periodically sharpen the chain. The chain can either be sharpened by a professional or by yourself by providing you with a sharpening guide (make sure you know how to use it).
-
Page 19: Declaration Of Conformity
BUILDER SAS 32 rue Aristide Bergès - Z.I. du Casque - 31270 Cugnaux - France Declares that the machinery designated below: Petrol chainsaw HTRT4140-1 Serial number: 20221221127-20221221526 Complies with the provisions of the Directive "machinery" 2006/42/EC and regulations National transposing it;... -
Page 20: Warranty
8. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 21: Product Failure
9. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 22: Warranty Exclusions
10. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...
Need help?
Do you have a question about the HTRT4140-1 and is the answer not in the manual?
Questions and answers