Advertisement
THE DYNAMO CEILING FAN
INSTALLATION INSTRUCTIONS
Please read and save these instructions
These instructions are to be used in
the installation of the following
OXYGEN fans...
The Dynamo
© 2020 oxygen Lighting. All Rights Reserved.
IO297-05/15
201 Railhead Rd • Fort Worth, TX 76106 • (877) 607-0202 • FAX (877) 607-0203
Advertisement
Table of Contents
Related Manuals for Oxygen Dynamo 3-113 Series
Summary of Contents for Oxygen Dynamo 3-113 Series
- Page 1 Please read and save these instructions These instructions are to be used in the installation of the following OXYGEN fans... The Dynamo © 2020 oxygen Lighting. All Rights Reserved. IO297-05/15 201 Railhead Rd • Fort Worth, TX 76106 • (877) 607-0202 • FAX (877) 607-0203...
-
Page 2: Safety Rules
Mounting hardware (wire nuts, wood screws, machine screws, lock washers, spring washers, metal washers.) 12. Blade balancing kit (l) IF YOU FIND THAT PARTS ARE MISSING. CONTACT YOUR DEALER FOR REPLACEMENT, OR CALL OXYGEN DIRECTLY AND WE WILL MAIL REPLACEMENTS TO YOU IMMEDIATELY. -
Page 3: Mounting Options
3. MOUNTING OPTIONS 1. Disconnect the power by removing fuses WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, OR PERSONAL INJURY, or turning off circuit breakers. MOUNT THE FAN ONLY TO AN OUTLET MARKED ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX. -
Page 4: Hanging Your Fan
4. HANGING YOUR FAN WARNING -Turn off the power! Fig. 5 Fig. 8 1. Remove the motor housing cover and metal washer by removing the six screws from the top of the motor housing. (Fig. 5) Screws Screws Metal 2. Attach the blades to the blade holder Metal washer washer... - Page 5 5. HANGING YOUR FAN Fig. 10 Fig. 12 WARNING -Turn off the power! DO NOT fasten the blades to the fan Downrod until it is assembled and hanging from assembly Safety cable the ceiling. To do so now will likely bend the blade arms and almost Hanger bracket certainly cause wobble.
-
Page 6: Electrical Connections
If your junction box has a ground wire Use ONLY wall controls approved by when making connections. Secure the (green or bare copper), connect the Oxygen. Use of unapproved wall connectors with electrical tape and make transmitter's ground wire to it. Otherwise, controls will cause unacceptable... - Page 7 7. COMPLETING INSTALLATION 1. Make sure the wiring is safely inside the outlet box as instructed in Step 6 - Fig. 14 Electrical Connections. To install the canopy, slide the canopy up to hanger bracket and place the key hole on the canopy over the screw on the hanger bracket, turn canopy Outlet box until it locks in place at the narrow section of the key holes.
- Page 8 8. OPERATING TRANSMITTER YOUR Your DC brushless motor is equipped with If a room has two fans installed, each fan Fig. 16 will need it’s own remote control. A an automatically learned type remote single control CAN NOT control more control.
- Page 9 9. FAN OPERATION AND CARE 1. A ceiling fan is an environmentally 3. Clean you fan periodically using only Fig. 18 smart choice to cool as well as to help a cloth dampened with a mild detergent warm your home or office. Adjust your solution for all hardware - never use HVAC thermostat during fan use to save solvents.
-
Page 10: Troubleshooting
10. TROUBLESHOOTING FAN WILL NOT START 3. Use of a standard light rheostat or an EXCESSIVE WOBBLE 1. Check that the electricity has been Note: A small amount of wobble is unapproved fan wall control to control the turned on at the circuit breaker which had fan speed will always cause an annoying considered acceptable and should not be probably been turned off during...
Need help?
Do you have a question about the Dynamo 3-113 Series and is the answer not in the manual?
Questions and answers