Advertisement
Quick Links
Engineered Beautifully™
BD4000 Series Privacy Barn Door Lock Set Parts List:
(With Face Fixing Trim Plate)
7
8
10
9
11
Wall Conditions and Tools Suggestion
Most of the drywall will have corner bead in steel or vinyl; it's strongly recommended to use Hole Saw to cut the holes for installing locks and
trim plates. Hole Saw for steel will also help cutting through any screws inside drywall or wood stud to make the installation job run faster.
DO NOT USE:
Spade Bit
BD4000 Privacy Barn Door Lock
INSTALLATION INSTRUCTIONS
5
3
4
6
1
Recommend to Use:
Installation based on barn door application where doors are hung on the
OUTSIDE of the room.
Install Lock Inside the Jamb Wall behind the barn door
-
Install Trim Plate on the Jamb Wall facing the opening
-
Install Strike with an emergency release on the barn door
-
Adjustable Strike for door thickness from 1-3/8" to 2-1/4".
-
Thick Door Kits Available.
-
Wall Thickness:
LOCK BOLT NO.
BACKSET
BD4214
2-1/4"
BD4312
3-1/2"
Items
Trim Parts
Strike
Others
2
Stud Finder
Level
( PM-IS1301-V161001 )
WALL THICKNESS
TYPICAL WALL STUDS
4-1/2"+
6-1/2"+
No.
Parts Description
1
Face Fixing Trim with spindle
2
M4 x 50 Slotted Head Screws
3
Barn Door Lock
4
M4 x 40 Wood Screws
5
Lock Bracket
6
Dust Proof Strike
7
Washer
8
Sleeve
9
Hollow Screw
10
Decorative Cap
11
Emergency Key
-
Door Prep Template
-
Installation Instruction
Hole Saw
2-1/8"
1-1/4"
1"
T-Square
2 x 4
2 x 6
Function
Privacy
1 EA
2 EA
1 EA
2 EA
1 EA
1 EA
2 EA
1 EA
1 EA
1 EA
1 EA
1 EA
1 EA
1/8" Drill Bit
1/4" Drill Bit
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for INOX BD4000
Summary of Contents for INOX BD4000
- Page 1 BD4214 2-1/4” 4-1/2”+ 2 x 4 BD4312 3-1/2” 6-1/2”+ 2 x 6 BD4000 Series Privacy Barn Door Lock Set Parts List: Function (With Face Fixing Trim Plate) Items Parts Description Privacy Face Fixing Trim with spindle 1 EA Trim Parts...
- Page 2 (gypsum board), minimum 2" door than 1-5/8" wide. Drill lock bore at least at least 1" from the edge. overlap is needed to install BD4000 2-1/4" from edge. For this type of installa- privacy lock. The lock bore center must be tion, door overlap must be at least 3".
- Page 3 Step 2. Prep Trim Bore – On the Jamb (CONT.) TIP: Before drilling, cover area around the bore hole with masking tape to prevent the drywall from chipping or cracking. With Casing 1-5/8” or wider: a. Drill through casing and drywall 2.3) With a 2-1/8”...
- Page 4 Step 4. Installation of the Lock (CONT.) Ensure spindle hub is at center of trim bore. Use spindle or screwdriver to 4.4) test bolt retraction; if not smooth, troubleshoot as follows: - Check 2-1/8" trim bore dimensions - Ensure hole is free of debris - Make sure 1"...
Need help?
Do you have a question about the BD4000 and is the answer not in the manual?
Questions and answers