INOX ED93F-CVRW Series Instructions For Installing

INSTRUCTIONS FOR INSTALLING ED93F-CVRW
fnox
®
SERIES CONCEALED VERTICAL ROD EXIT DEVICE
u s
A
(6)# 1 /4"x2"
..
..
_ _
..
_ _
- - '-�
Top
'
Chassis
-�\
Top
(2)# 5Mx0.8x15/32"
Bolt
Top �
Inner Chassis
Rod-
1
D Mounting Plate
(2)#12x1-1/2"
wood screws
�, ; , 4 ,
I
I '
I : .,
"'
� I
(] @ ...... ,,,
,,,
.,
....J -.J ,,.
6l\ (},
,,.
Inner
..,, -"'
[f ® .... ,
Chassis
ij
EJ ', � � /
®
®
' , ,
��i r
i
Rod­ (2)# 3/16"x1-1/4"
wood screws
5Mx0.8x3/4"
Bottom
Rod_
Bottom �
Case - �
i ___,--
(2)# 3/16"x1-1/4"
wood screws
'
INSTRUCTIONS FOR INSTALLING INOX ESC LEVER TRIM FOR
ED93CVR SERIES CONCEALED VERTICAL ROD EXIT DEVICE
1. Through Inner Chassis cutout in the door, insert the extension in the door.
2. Insert Inner Chassis in the cutout, insert reduced end of extension in top
threaded bushing on inner chassis, and fasten the rod extension with 1
machine screw.
3. On outside of door through the cutout, install Plate into extension in the door.
4. Before attaching main chassis and inner chassis to the door, attach esc lever
trim to the door with (2) 1/4-20 x 2-3/8" flat head machine screws.
5. Then attach Rail Assembly to the chassis, and hinge stile end of rail to the door
with mounting bracket.
Inner Chassis Mounting Plate
Holes for
LHRB doors
1-17/3
2-29/32"
l 1 r
-� - - - - - - - -a1c- =ici.=,.tt
C'sink for / \
1/4"-20 flat Holes for
Head Machine LHRB doors
Screws
Available stock length
- For 32" doors, Device can be cut to
fit doors down to 24 " wide
- For 36 " doors, Device can be cut to
fit doors down to 32 " wide
- For 48 " doors, Device can be cut to
fit doors down to 36 " wide
Door Surface must be flush
to al low Exit Device rest
Main
on flat surface of the door
Chasis
(4)# 3/16"x1-1/4"
wood screws
Outside surface for Door
/
0.23" DIA, THRU DOOR,
Outside for 0.37"
(4 Reqd)
-r- �
I
I
I
I
i
' T l
I
I
25/32" 25/32"
THIS EXIT DEVICE IS HANDED
CHECK HAND OF DEVICE AGAINST APPLICATION
RIGHT HAND
REVERSE BEVEL
Mounting
(4)5/32"x32x1/4"
machine screws
INSTRUCTIONS FOR INSTALLING INOX WOOD DOOR ESC TRIM
ED93CVR SERIES CONCEALED VERTICAL ROD EXIT DEVICE
1. Thru Inner Chassis cutout in the door, insert the extension in the door.
2. Insert Inner Chassis in the cutout, and insert reduced end of extension in top
threaded bushing on inner chassis, and fasten the rod extension with 1 machine
screw.
3. On outside of door through the cutout, install Plate into extension in the door.
4. Attach mounting plate to inner chassis with 2 machine screws, then attach
mounting plate to the door with 2 wood screws.
5. Attach WD Esc trim to the door. Then attach Rail Assembly to the chassis, and
hinge Stile end of rail to the door with mounting plate.
Install
1-5/8"
Chassis
<i
-13/32
6-15/32"
OUTSIDE FOR DOOR
41"FROM
FINISHED
1-1/2"
�
FLOOR
REF
J I
OUTSIDE
_J
INSIDE
OUT
LEFT HAND
REVERSE BEVEL
�
DOUBLE DOORS
MOUNT TRIM
ATTACH
OUTSIDE
TRIM IF
USED
IF AN OUTSIDE
AUXILIARY
CONTROL IS
USED, SEE THE
INSTRUCTION
SHEET PACKE
WITH THE MOUNTING
INSTRUCTION SHEET
CONTROL
PACKED WITH TRIM
Install for Door
Top Rod
i
0
Plate
Extension
' '
'
1 ......
/
/
�so,
' '
'
' -�
'
t - - - - -
'�- (2) wood screw
i
i
Bottom Rod
1,::T��
End Cap
Mounting
Plate
(1) Machine screw
5Mx0.8x1/2"
3/16"x1-1/4" (2)
ED93