Page 1
LEDPAR715RGBW 7x10W RGBWAUV Battery PAR LED USER MANUAL...
Page 2
7pcs*8W RGBWAP LEDs. IR remote control is included. The house is made of extruded aluminum and die-cast aluminum cover. The ingress protection rating is IP20. However, there is no glue was used into the light. LEDPAR715RGBW has won many certifications, including the CE, ROHS and so on.
Page 3
Features ● Light Source: 7pcs , 10W 6 in 1 RGBWAUV LED ● Beam Angle:25° ● Life Time:80000-100,000 hours ● Dimming 0-100%with regulated constant color control ● Strobe: 10 Flashed per second (any color) ● Operation Mode:DMX 512,Manual.sound.internal program ● DMX control: 4 DMX mode,(6CH,8CH,11CH,18CH) ●...
Programme Menu DMX ADDRESS 06CH 08CH CHANNELS MODE 11CH 18CH CURV 1 CURV 2 DNX CURVE CURV 3 CURV 4 DMX HOLD DMX STATE BLACKOUT DMX fail SLAVE SLAVE MODE SPEED AUTO MODE AUTO SEMS Sound MODE SOUND GREEN BLUE MANUAL MODE WHITE AMBER...
Page 5
Dimmer Dimmer Dimmer BALANCE GREEN Dimmer BLUE Dimmer WHITE Dimmer SET UP Dimmer AMBER Key locks REMOTE Display RESET 600HZ 1200HZ REFRESH RATE 2400HZ 4800HZ 9600HZ 15000HZ 30°C Max temp 70°C Software VER V1.1 WORKING times INFO 000000h 01m RDM:UID 010e:ffffffff...
Page 6
Displayer introduction ① ② ③ temp:043 ④ ADDRESS Key lock open ⑤ 1. DMX means the light is in the DMX mode.Similarly,SLAVE means the light is in the SLAVE mode. 2. The color of the point shows the condition of signal transmission. Green represents the good condition, while red represents the signal is interrupted.
Page 7
DMX ADDRESS - In this menu, you can connect several pieces of lights with DMX cable and control them with control console. 1. Press “ENTER” button and then UP or DOWN button until “DMX ADDRESS ” is showed. 2. Press “ENTER” button, “xxx” will be showed, “x” represents the showed address. You can press the UP or DOWN button to select your desired address.
Page 8
MANUAL MODE – In this menu, you can adjust the value of static color and strobe speed as you like. 1. Press “ENTER” button and then UP or DOWN button until “MANUAL MODE” is showed. 2. Press “ENTER” button, and there will be five options. Then, press ENTER to select the option and press UP or DOWN button to select the value you desire as follow: 1) RED - You can adjust the red brightness in this menu.
DMX control mode DMX 6 channel channel value function 0 - 255 Red dimmer 0 - 255 Green dimmer 0 - 255 Blue dimmer 0 - 255 White dimmer 0 - 255 Amber dimmer 0 - 255 UV dimmer DMX 8 channel value function channel...
Page 10
channel value function 051-060 Auto 4 061-070 Auto 5 071-080 Auto 6 081-090 Auto 7 091-100 Auto 8 101-110 Auto 9 111-120 Auto 10 121-220 Sound Mode 221-255 reserved 0-255 Speed slow to fast DMX 18 channel channel value function 0 - 255 Master dimmer 0 - 255...
Page 11
channel value function 081-090 Auto 7 091-100 Auto 8 101-110 Auto 9 111-120 Auto 10 121-255 reserved 0-255 Speed slow to fast...
Page 12
The installaiton should be checked by a skilled person once a year. The LEDPAR715RGBW is fully operational in two different mounting positions, hanging upside-down from a ceiling or set on a flat level surface.
CABLE CONNECTORS Cabling must have a male XLR connector on one end and a female XLR connector on the other end. DMX connector configuration GROUND caution:Do not allow contact between the ground and the fixture’s chassis ground. Grounding the ground can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify positive pole and to make sure the pins are not grounded or shorted to the shield or each other.
Page 15
IR Controller Power on/off button SLAVE DMX button,to control DMX address when AUTO AUTO SPEED press this button.It is channel mode when double click. SOUND SOUND Master-slave mode button. SLAVE STROBE DOWN AUTO AUTO Automatic mode button SPEED Speed adjustive button SOUND SOUND Sound mode button...
Need help?
Do you have a question about the LEDPAR715RGBW and is the answer not in the manual?
Questions and answers