Subscribe to Our Youtube Channel
Related Manuals for Teknatool Nova Voyager DVR
Summary of Contents for Teknatool Nova Voyager DVR
- Page 1 Voyager DVR Drill Press OPERATING INSTRUCTIONS Model: 58003 (EU model) Original Operating Instructions DT58003_Voyager DVR_BDA_2024.V03 © Teknatool International All rights reserved.
- Page 2 Alternatively, you can contact the retailer where you purchased your product. Applied directives/standards • Machinery Directive 2006/42/EC • Electromagnetic Compatibility (EMC) Directive 2014/30/EU Applied harmonised standards: EN ISO 12100:2010 EN 60204-1:2006+A1: 2009+AC:2010 EN 12717:2001+A1:2009 EN 61000-6-2:2005+AC:2005 EN 61000-6-4:2007 + A1:2011 © Teknatool International | Original-Operating Instructions...
-
Page 3: Table Of Contents
08 | Information on noise emission ............................8 09 | Labels on the machine ................................ 9 10 | NOVA Voyager DVR Features ............................10 11 | Transport package content .............................. 11 12 | Assembling and adjusting the drill press ........................12 13 | Connecting to power ................................. -
Page 4: Warranty
Damaged or entangled power cords increase the risk of an electric shock. If operating the power tool in a damp environment cannot be avoided, use a residual-current circuit breaker. Using a residual-current circuit breaker reduces the risk of an electric shock. © Teknatool International | Original-Operating Instructions... - Page 5 Personal safety Be attentive, pay attention to what you are doing and take the utmost care when operating a power tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness when using a power tool can cause serious injury.
-
Page 6: Health And Safety Instructions For Drill Presses
Check the set-up with the spindle off. Rotate the workpiece by hand to check the clearance before turning on the spindle. Always check that the correct speed is set before switching on the spindle. Do not open any covers or switches. Do not make adjustments when the spindle is turning. © Teknatool International | Original-Operating Instructions... -
Page 7: Safety Devices
Chuck guard Your NOVA VOYAGER DVR Drill Press is equipped with a chuck guard. As soon as the guard is opened, the protective device is triggered and work is no longer possible. The motor cannot be restarted until the chuck guard is closed. -
Page 8: Drill Press Technical Data
The acceptable exposure rates may vary from country to country. For all these reasons, we recommend the user to wear an appropriate ear protection while working on the machine. © Teknatool International | Original-Operating Instructions... -
Page 9: Labels On The Machine
09 | Labels on the machine Nameplate Motor nampeplate Warning label Version 2024.V03_EN... -
Page 10: Nova Voyager Dvr Features
10 | NOVA Voyager DVR Features A belt drive usually has a 2 HP DVR Smart Digital Motor delivers power loss of around correct speed and power to maintain 20%. Direct drive power and optimal torque to the drill head. -
Page 11: Transport Package Content
11 | Transport package content Item Description Order number Headstock 8338055 Column 8338028 Base 8338025 Table 8338046 Table arm 8338054 Crank handle arm for table adjustment 8338036 Clamping lever 8338032 Quill driving handle 8338009 Hex key (3x) AK4, AK5, AK6 Crank handle for table adjustment 8338037 Open-ended spanner... -
Page 12: Assembling And Adjusting The Drill Press
6. Insert the rack into the table arm as shown in the adjacent figure so that the rack teeth are mating with the worm gear. Pay attention to the teeth angle with respect to the table arm orientation. Position the table arm partway on the rack. © Teknatool International | Original-Operating Instructions... - Page 13 7. Slide the table arm with the mounted rack from above onto the column and insert the bottom of the rack into the mating groove in the column base. 8. Slide the top ring down and over the rack ensuring that the groove on the ring that serves as guide for the rack is facing down.
- Page 14 2. Loosen the safety screw underneath the screw you just loosened with a 5 mm hex key. 3. Tilt the table to the desired position. 4. Retighten the hex head screw and the safety screw. Make sure the table is securely locked in place before drilling. © Teknatool International | Original-Operating Instructions...
- Page 15 Quill lock 1. To lock the quill at a certain depth, pull the quill down to the desired position. 2. Tighten the clamping lever by turning it clockwise until the quill is locked. If the quill cannot be locked even though the clamping lever is fully tightened, proceed as follows: a.
-
Page 16: Connecting To Power
Ensure adequate ventilation in your workshop. The degree of ventilation depends on the size of the workshop and the amount of work that is done. The use of dust collectors and filters will reduce harmful substances and minimise your health risk. © Teknatool International | Original-Operating Instructions... -
Page 17: Operating The Drill Press
Insert the plug into the socket and turn on the drill press by switching the rocker switch to “I”. When the NOVA Voyager DVR Drill Press has been powered up, the product name and logo will be displayed on the LCD screen followed by warning messages. - Page 18 Press the red <OFF> button to stop the spindle and reset the user interface. Note: The <ON> and <OFF> buttons only switch the motor on and off. The pre-set speed will remain until it is adjusted or until the computer is switched off. © Teknatool International | Original-Operating Instructions...
- Page 19 Use the dial to change the speed when the machine is running or stopped. Turn the dial in the clockwise direction to increase the speed. Turn the dial in the anti-clockwise direction to decrease the speed. By simply turning the dial you will make a coarse adjustment. By pressing and turning the dial you will make a fine adjustment.
-
Page 20: User Interface
To select a menu item, press the <ZERO / Confirm> button. ZERO Confirm To move the cursor up, turn the dial counterclockwise or press the <F1> button. To move the cursor down, turn the dial clockwise or press the <F2> button. © Teknatool International | Original-Operating Instructions... - Page 21 FORWARD/REVERSE> <Speed Chart> After selection of the drill bit type, drill bit size and workpiece material, the integrated speed chart enables your NOVA Voyager DVR Drill Press to determine a recommended speed and set it automatically. Note: The speed chart is available in both metric and imperial units. Select menu item <Configuration>...
- Page 22 After a fixed amount of time, the direction of rotation changes again and the cutting procedure continues. This repeats until the drill press senses the tapping is complete OR until the user presses the <ON> button. Note: This mode is only recommended for through holes. © Teknatool International | Original-Operating Instructions...
- Page 23 2. <Chip Breaker>: This mode uses the load sensor to determine when tapping has been started and when a chip breaking cycle has to be entered. After a fixed amount of time, the machine changes the direction of rotation in order to break the chip for a fixed amount of time.
- Page 24 (e.g. if a workpiece has been caught or is spinning around). You can choose between the following four settings: • <OFF> (default) • <LOW> • <MEDIUM> • <HIGH> © Teknatool International | Original-Operating Instructions...
- Page 25 The firmware version can be upgraded using a USB cable and a PC with internet access. The latest firmware version is available on the manufacturer's site www.teknatool.com. Regular updates offer new features and software improvements and thus enhance the performance of your machine.
-
Page 26: Care And Maintenance
The same applies to cleaning rags or polishing wool soaked in oils, greases, solvents and cleaning agents. Of course, you can also bring your defective machine to your local dealer. He will ensure proper recycling. © Teknatool International | Original-Operating Instructions... -
Page 27: Speed Chart
19 | Speed chart The values in the table below are reference values. Depending on the material, tool and experience of the user, the actually needed speeds may vary. *Fields highlighted in red are not recommended areas* Material Hard Glass / Tool diameter Soft wood Acrylic... -
Page 28: Troubleshooting
3. Stand on which the drill press is 4. Use a sharper drill bit or sharpen blunt tools. mounted. 5. Refer to the speed chart. 4. Drill bit: Check if the drill bit is blunt or damaged. 5. Wrong drilling speed. © Teknatool International | Original-Operating Instructions... - Page 29 If an error message is displayed and the drill press cannot be used anymore, please contact your dealer or customer service. At best, you already have your invoice with the date of purchase (start of warranty) at hand. You can also contact the NOVA customer service directly: service@teknatool.com (in writing in English). Version 2024.V03_EN...
-
Page 30: Terms Of Extended Warranty
21 | Terms of extended warranty Teknatool grants an extended warranty on this product from the date of purchase: 5 years on mechanical parts (working hours excluded after 2 years) and 2 years on electrical parts. If defects in material or workmanship occur during the intended use of the product, please contact your dealer. -
Page 31: Exploded View - Headstock
22 | Exploded view - headstock Version 2024.V03_EN... -
Page 32: Exploded View - Stand And Table
23 | Exploded view – stand and table © Teknatool International | Original-Operating Instructions... -
Page 33: Parts List - Drill Press
24 | Parts list - drill press Item Part number Designation Item Part number Designation C05016 Cap screw M5x16 8339026 Control panel 8330355 Top cover 8338021 Emergency stop button C08040 Cap screw M8 C05020 Cap screw socket head M5x20 55431 Location pin 52003 Fan encoder... -
Page 34: Wiring Diagram
25 | Wiring diagram © Teknatool International | Original-Operating Instructions... -
Page 35: Declaration Of Conformity
26 | Declaration of conformity Version 2024.V03_EN... - Page 36 Nova Voyager DVR Operating Instructions © Teknatool International 2024...
Need help?
Do you have a question about the Nova Voyager DVR and is the answer not in the manual?
Questions and answers