Table of Contents
Advertisement
Quick Links
Digital Film Imager
This manual is comprised of the Instructions for Use and the Setup Manual.
The Instructions for Use gives the information on how to use the printer for the
routine work.
The Setup Manual gives the system administrator the information needed to set-
up the printer and connect it to the network.
Instructions for Use
Setup Manual
Before operating the unit, please read this manual thoroughly
and retain it for future reference.
UP-DF760
© 2017 Sony Corporation
Page 8
Page 52
4-597-660-11 (3)
2016-09
Advertisement
Chapters
Table of Contents
Related Manuals for Sony UP-DF760
Summary of Contents for Sony UP-DF760
- Page 1 The Setup Manual gives the system administrator the information needed to set- up the printer and connect it to the network. Instructions for Use Page 8 Setup Manual Page 52 Before operating the unit, please read this manual thoroughly and retain it for future reference. UP-DF760 © 2017 Sony Corporation...
- Page 2 WARNING Storage and transport temperature This symbol indicates the acceptable To reduce the risk of fire or electric shock, do not temperature range for storage and transport expose this apparatus to rain or moisture. environments. To avoid electrical shock, do not open the Storage and transport humidity cabinet.
- Page 3 6. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause interference to other equipment. If this unit causes interference (which can be determined by unplugging the power cord from the unit), try these measures: Relocate the unit with respect to the susceptible equipment.
- Page 4 Important EMC notices for use in the medical environments • The UP-DF760 needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in the instructions for use. • The portable and mobile RF communications equipment such as cellular phones can affect the UP-DF760.
- Page 5 Guidance and manufacturer’s declaration - electromagnetic immunity The UP-DF760 is intended for use in the electromagnetic environment specified below. The customer or the user of the UP-DF760 should assure that it is used in such as environment. IEC 60601 test...
- Page 6 Guidance and manufacturer’s declaration - electromagnetic immunity The UP-DF760 is intended for use in the electromagnetic environment specified below. The customer or the user of the UP-DF760 should assure that it is used in such as environment. IEC 60601 test...
- Page 7 Recommended separation distances between portable and mobile RF communications equipment and the UP-DF760 The UP-DF760 is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the UP-DF760 can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the UP-DF760 as recommended below, according to the maximum output power of the communications equipment.
-
Page 8: Table Of Contents
Instructions for Use Messages ..............43 Table of Contents Error Messages ..........43 Other messages ..........44 Troubleshooting ............45 If Damage is Suspected ........45 Introduction If the Film Sheets Jams ........45 System Overview ............9 License ..............49 System Configuration Example ......9 Index ..............51 Location and Function of Parts and Controls ...10 Preparation Supplied Accessories ..........13 Removing the Packing Materials ......13... -
Page 9: Introduction
DICOM format, sent from image diagnosis equipment such as CTs, MRIs, CR, DR and so on. The UP-DF760 digital film imager is a thermal printer The following shows a system configuration example. designed to reproduce image data in DICOM format sent via a network. -
Page 10: Location And Function Of Parts And Controls
(about 279 × 355 mm)) are ejected onto this tray, which also serves to prevent sheets from dropping. The tray size must match the film size. If a change is necessary, please contact your Sony dealer to have the procedure performed. J Front cover lock lever Used to open the front cover. - Page 11 U Cable stopper 14 × 17 (about 353 × 430 mm). To use films of other sizes, contact your Sony dealer to have the tray size Secures the network cable to prevent it from being changed. Printed film sheets are ejected onto this tray.
- Page 12 Standard screen (when error has occurred) Menu screen (Settings screen) A Error countermeasure illustration A Menu item name Shows an illustration indicating the appropriate step Shows the name of the currently displayed item. The to take for correcting the error that has occurred. “>”...
-
Page 13: Preparation
Removing the Packing Materials Preparation Before using the unit for the first time, be sure to remove the packing materials from inside the unit and film trays. Open the top cover and inner cover (page 48), and Supplied Accessories remove the packing materials from inside the unit. The unit is packed together with the following accessories. -
Page 14: Assembly
• The size of the supplied output tray must be adjusted to Holding both sides of the output tray with both hands, match the film tray size. Please contact your Sony dealer insert it all the way into the unit. -
Page 15: Placing The Unit
Small Size Connections Please contact your Sony dealer to have the size changed to this setting. Connect the unit to a LAN. Output tray stopper Notes • Turn off the power of each device before attempting to make any connections. - Page 16 When you use the unit for the first time main power switch Note The unit is not turned on even if the ?/a main power The above message should appear when you use the switch of the unit is turned to the on (?) side. unit for the first time, because the film sheets are not loaded in the film trays of the unit.
- Page 17 When you do not intend to use the printer for a long time Turn the printer off as follows. Press the 1ON/STANDBY switch. The 1ON/STANDBY indicator blinks and the message “Please Wait” appears on the LCD. Then the message disappears, the unit turns off and the 1ON/ STANDBY indicator lights up in orange.
-
Page 18: Operation
In the factory default condition, this is set for film size 8 × 10 (about 202 × 253 mm). Note To use films of other sizes, contact your Sony dealer to Be sure to use film sheets made expressly for the UP- have the tray size changed. - Page 19 When the film sheets loaded in either film tray 1 Loading film sheets or film tray 2 have been used up: Proceed as follows to load film sheets. The following explains how to load film sheets using film tray 1 as an example. Load film sheets in the lower tray in the same way as you do for the upper tray.
- Page 20 Open the film tray cover by putting your fingers in the Note grooves on both sides of film tray 1, and pulling it upward in the direction of the arrow. Remove the seal after loading the film into film tray 1. If you remove it before loading, the film sheets may slip and drop.
- Page 21 Hold the damp-proof bag with both hands so that the • Do not add film sheets halfway through one bag of opened side faces toward the inner side of the tray and film sheets. The reason for this is because the unit place film sheets in the film tray so that the printing counts the remaining film sheets using the IC tag on surface faces down, with the printing surface...
- Page 22 3 Close the film tray cover. • If you try to insert the film tray into the wrong film tray side, you cannot do so because the stopper prohibits you from inserting the tray all the way in. Insert film tray 1. If the cover of the film tray comes off Remove the film tray and re-attach the cover.
-
Page 23: Printing
If you can see the film sheets in the film tray Printing If you slant the film tray, film sheets may move to the outlet of the film tray. This may cause film jamming. In such a case, put the film sheets back inside the film tray by Before printing pushing them with your finger, as shown below. - Page 24 1 and 2 and the output tray type, the indication “OutputTrayMismatch” may appear. In such a case, the output tray size must be changed. Please contact your Sony dealer to have the size adjustment performed. • To prevent film jamming, do not allow more than 30 printouts to remain on the film output slot.
- Page 25 If the unit does not print When an error message is displayed on the LCD, the unit does not print. Take remedies according to the information given in “Messages” (on page 43). When the film sheets run out during printing The message “Set Film”...
-
Page 26: Adjustment
Adjustment Adjustment and Setting Using a Menu You can set the following items using the relevant menu: • Confirming information (Information) (page 28) • Adjusting the print quality (Print Quality) (page 28) • Calibration (Calibration) (page 31) • Selecting a gamma curve (Default Gamma) (page 33) •... -
Page 27: Menu Configuration
Menu Configuration The F and f buttons serve to move within the same level. The G and g buttons serve to move up and down among levels. (Except in some cases) In any level, pressing the MENU button will bring up the standard screen. (Standard screen) Level 1 Level 2... -
Page 28: Menu Operation
(light areas of images). Notes • You cannot adjust the gamma curve itself using the menu. To change the gamma curve, contact your Sony dealer. • To make a printout of the pattern print to be used for... - Page 29 Press the F or f button to move the cursor to “Print After the sharpness has been adjusted, print a density Quality,” and then press the g button. pattern and adjust the value while checking the The unit enters the gamma selection mode. printed result.
- Page 30 When the density pattern printing is completed, the Press the EXEC button. following screen appears on the LCD panel. The low tone setting is stored, and the following (If the screen does not appear, press the G button to screen appears on the LCD panel. return to step 3, press the F or f button to move the (If the screen does not appear, press the G button to cursor to “Point 95%”, and then press the g button.)
-
Page 31: Calibrating The Printing Density
Display the “Save Gamma” by pressing the EXEC It is recommended to perform this operation when new button. film was inserted. Press the EXEC button. The gamma curve adjustment values selected in step 3 are stored and will be effective from the next printing operation. - Page 32 2 Press the F or f button to select the tray The setting next to the cursor becomes effective. containing the blue thermal film for which the calibration is to be carried out. Item Setting The printer performs the calibration 3 Press the EXEC button.
-
Page 33: Selecting A Gamma Curve
2 Press the F or f button to move the cursor to the To reset another type of blue thermal film blue thermal film for which you want to restore to the default status the default setting. Repeat steps 1 to 4. Selecting a Gamma Curve If the gamma curve has not been specified at the modality side, the gamma curve selected at the unit will be used for... -
Page 34: Making Network And Lcd Panel Settings
The menu screen closes and the unit returns to the desired gamma curve. standard screen. The gamma curve for SONY 1 has been pre-set, you cannot change these settings. Making Network and LCD Panel The gamma curves for USER 2 to USER 20 can be set to the desired value. - Page 35 Network settings should only be LCD Contrast changed by the system administrator. If settings need to be changed, contact your Sony dealer. LCD BackLight A value indicating the current LCD panel contrast setting is shown on the menu screen. The contrast setting range is 1 - 20.
-
Page 36: Test Print
Language Press the F or f button to move the cursor to “Test Print,” and press the g button. Press the F or f button to move the cursor to the desired language setting. A screen for selecting the pattern appears. The change in language setting becomes effective the next time power to the unit is turned on. -
Page 37: Other Settings
SONY 1 gamma curve. For USER 6 to USER 20: The same setting as the one of SONY 1 is applied. Press the EXEC button. The test image pattern is printed. When printing is completed, the following screen appears. -
Page 38: Miscellaneous
5,000 printings. However, you condensation forms, turn off the power and allow the should ask your Sony dealer to perform this maintenance. printer to stand for at least one hour. You can check the total number of prints using the Total •... - Page 39 Remove the packing film on the new cleaning roller Notes and attach the new cleaning roller. • Before starting the following maintenance, be sure to turn the unit off by pressing the 1ON/STANDBY switch on the front panel. • When cleaning the unit, do not exert strong pressure on the platen rollers (black rollers), to prevent the possibility of damage and uneven printing.
- Page 40 Wipe the thermal head with the cleaning sheet. Cleaning the filters Ventilation holes are provided on the unit to prevent it from overheating. Three filters are provided on the front cover for covering the ventilation holes. Caution Do not touch the thermal head just after printing. To clean the filters, proceed as follows.
-
Page 41: Specifications
Reset the filters and close the cover. Specifications Power requirements AC 100 V-240 V, 50/60 Hz Input current 4.4 A-2.4 A Operating temperature 10 °C to 30 °C (50 °F to 86 °F) Operating humidity 20% to 80% (no condensation allowed) Operating pressure 700 hPa to 1,060 hPa Storage and transport temperature... - Page 42 OR FOR ANY OTHER REASON MEASURES ON TRANSMISSION DEVICES, WHATSOEVER. UNAVOIDABLE DATA LEAKS RESULTING • SONY WILL NOT BE LIABLE FOR CLAIMS OF FROM TRANSMISSION SPECIFICATIONS, OR ANY KIND MADE BY USERS OF THIS UNIT SECURITY PROBLEMS OF ANY KIND.
-
Page 43: Messages
• This film is specifically designed for Sony imagers. Do again, turn power to the unit off and contact your Sony dealer. not use with imagers from other manufactures. -
Page 44: Other Messages
Head Heating again, turn power to the unit off message disappears. and contact your Sony dealer. The printer is performing an internal Please Power OFF This unit cannot be placed vertically. processing operation such as when... -
Page 45: Troubleshooting
1ON/STANDBY switch installed. (page 14) Output Tray to turn the unit on. (Page 16) Contact your Sony dealer to have the Mismatch • The connections may not be correct. output tray size changed. tMake the connections correctly. - Page 46 Remove jammed film according to the status “XXXXXX” string Countermeasure displayed. (jam location) Tray 1 (Film tray 1) For information on how to remove When a film sheet pops out from the shutter Tray 2 (Film tray 2) film jammed in the film tray, see of the feeding position of the film tray: page 46.
- Page 47 To remove film jammed inside the printer When the top cover is opened Open the cover indicated in the message and remove the jammed film sheet slowly while holding the film with both hands. When rear cover 1 is opened When the front cover is opened When rear cover 2 is opened When the top cover and front cover are...
- Page 48 When the top cover and inner cover 1 are The following message appears on the LCD. opened Wait until the message disappears. When the unit enters standby status, the following message appears. When the top cover, inner cover 1, and inner cover 2 are opened To remove film jammed in the output tray Remove the output tray completely.
-
Page 49: License
Remove the jammed film near the inside of the unit. License “zlib”, “The FreeType Project LICENSE” and “OpenSSL” software are used in this unit. We use these software based on license agreements with their owners of copyright. Based on requests by the owners of copyright of these software applications, we have an obligation to inform you of the following. - Page 50 MERCHANTABILITY AND FITNESS FOR A 2. Redistributions in binary form must reproduce the above PARTICULAR PURPOSE ARE DISCLAIMED. IN NO copyright notice, this list of conditions and the following EVENT SHALL THE OpenSSL PROJECT OR ITS disclaimer in the documentation and/or other materials CONTRIBUTORS BE LIABLE FOR ANY DIRECT, provided with the distribution.
-
Page 51: Index
cleaning kit 39 Index System Maintenance configuration example 9 cleaning the filters 40 feature 9 cleaning the thermal head 39 replacing the cleaning roller 39 Adjusting the print quality Menu sharpness 29 Calibration 31 Troubleshooting Configuration 27 if damage is suspected 45 Default Gamma 33 if the film jams 45 Information 28... - Page 52 This Setup Manual provides information for system Table of Contents administrators about the topics listed below, including the setup procedure for connecting the UP-DF760 (subsequently called “the unit”) to a network. The Setup Manual consists of the following parts. Setup About the IP Address ...........53...
-
Page 53: About The Ip Address
Setup Setting the IP Address To assign an IP address to be used by the unit, perform the following steps. About the IP Address Note When you use the unit for the first time immediately after If network settings are changed by mistake to unsuitable you purchase the unit, it is necessary to make settings for values, the unit will no longer be accessible via the the DICOM section integrated in the unit, such as... - Page 54 Press the g button. The Edit Preset screen appears. The network setup screen appears. Press the g button. Up to five different network settings can be saved in the A screen for selecting the Preset (Preset 1 - 5) or unit as Presets.
- Page 55 Note You can specify any character string (such as “SONY”) as AE title, but once the string has been set, a print request calling an AE title that does not match the string will not be accepted. To allow a request with any called AE title to be accepted, make the AE title blank.
- Page 56 Press the EXEC button. The current settings of “Preset 2” are shown. The Save Settings screen appears. Use the F and f buttons to move the cursor to “Save Move the cursor to “YES” and press the EXEC Settings” and press the g button. button.
-
Page 57: Completion Check
Completion Check After the setup procedure is completed, perform the following steps to verify that the settings have been correctly implemented. Connect the unit to the network. Turn on the unit. Mount a tray with blue thermal film loaded. Send image data from the modality. If the unit has been set up correctly, printing starts. -
Page 58: Network Setup Screen Transition Diagram
Network Setup Screen Transition Diagram This diagram shows the overall flow of the network setup procedure. Use it when wishing to return to earlier screens etc. Setting the IP Address...