Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for ASCHER RACING 76080062
Summary of Contents for ASCHER RACING 76080062
- Page 1 76080062 KNOB KIT PRO ASSEMBLY MANUAL 2024 – Ascher Racing GmbH...
- Page 2 1. DISMOUNT KNOBS – ROTARY 11. Mount PCB 2. DISMOUNT KNOBS – JOYSTICKS 12. Mount rotary switch TABLE OF 3. DISMOUNT CASING – FRONTPLATE 4 13. Mount rotary switch 4. UNPLUG CABLES 14. Mount casing – frontplate CONTENTS 5. DISMOUNT ROTARY SWITCH 15.
- Page 3 1. DISMOUNT KNOBS - ROTARY torque: 0,45 nm use plastic card to create a gap of 1mm between knob and frontplate...
- Page 4 2. DISMOUNT KNOBS - JOYSTICKS turn joystick so that the hex tool fit‘s in the groove of to plastic button cover...
- Page 5 3. DISMOUNT CASING - FRONTPLATE torque: 4,0 nm torque: 1,8 nm frontplate back Casing binder nut back casing on cable connector...
- Page 6 4. UNPLUG CABLES unplug all cables circled in...
- Page 7 5. DISMOUNT ROTARY SWITCH torque: 0,5 nm unscrew on Frontplate...
- Page 8 6. DISMOUNT PCB remove the screws circled in red. torque: 1,0 Nm...
- Page 9 7. DISMOUNT THUMB ENCODERS torque: 0,15 nm PUSH PUSH...
- Page 10 8. SWAP THUMB ENCODER 3) push knob against shaft (axial direction) 1) insert knob 4) tighten grub screw (0,9 mm hex tool) 2) slot perpendicular to grub screw torque: 0,3 nm...
- Page 11 9. MOUNT THUMB ENCODERS torque: 0,15 nm PUSH PUSH knob in the middle knob in the middle equal gap left and right equal gap left and right...
- Page 12 10. MOUNT PCB...
- Page 13 11. MOUNT PCB plug-in display cable torque: 1,0 nm 1) twist encoder cables 2) route cables exactly as shown 3) plug-in encoder cables set correct shifter mode: DOUBLE align PCB as centered as possible so that button caps move freely push PCB against frontplate in centered position slightly tighten 4 corner screws to fix position tighten all screws to specified torque...
- Page 14 12. MOUNT ROTARY SWITCH torque: 0,5 nm rotary switch nut rotary Switch PCB for frontplate...
- Page 15 12. MOUNT ROTARY SWITCH connect FFC cable...
- Page 16 13. MOUNT CASING - FRONTPLATE make sure to not squeeze any cables when closing the steering wheel mount casing double check to not squeeze any cables twist wires connect shifters & clutches double check correct shifter mode: DOUBLE...
- Page 17 14. MOUNT CASING - FRONTPLATE perfectly align outlines of frontplate and casing before tightening screws torque: 4,0 nm torque: 1,8 nm frontplate back Casing binder nut...
- Page 18 15. MOUNT KNOBS - JOYSTICK hold joystick knob with fingers do not tighten the grub screw without holding when tightening the grub screw! the knob in order to avoid joystick damage! turn joystick so that the hex tool fit‘s in the groove of to plastic button cover...
- Page 19 16. MOUNT KNOBS - ROTARY torque: 0,45 nm use plastic card to create a gap of 1mm between knob and frontplate...
- Page 20 Now get back behind the wheel and enjoy! For questions regarding the process of swapping any components, please don‘t hesitate and contact info@ascher-racing.com...
Need help?
Do you have a question about the 76080062 and is the answer not in the manual?
Questions and answers