Standard Equipment; 916 Roll Groover Models; Roll Groover Assembly Instructions; Installing 916 Roll Groover On 300 Power Drive - RIDGID 916 Manual

Depth Adjustment .......Adjustment Screw
Actuation......................Integral Single Stroke Handle
Mechanism
Power Drive
Mounting ......................300 Power Drive, 1822 -I
Threading Machine, 535M,
535A Threading Machines,
300 Compact Threading
Machine
Weight..........................33 lbs.

Standard Equipment

Grooving Roll.................1
6" Schedule 10)
Driving Roll ....................1
6" Schedule 10)
Feed Handle..................Tubular Design
Drive Bar Adapter..........(When Required)
916 Roll Grooving Models
Catalog Model
No. No. Description
45007 916 Roll Groover for 300 Power Drive
46852 916 Roll Groover for Copper Tubing for 300 P.D.
60382 916 Roll Groover for 535
48307 916 Roll Groover for 1822
48307 916 Roll Groover for 300 Compact Mounted on 100,
150 and 200 Stands
45007 916 Roll Groover for 300 Compact Mounted on
250 Stand (Also requires 67662 Adapter Bracket)
Accessories
45347 — Roll Set for 1" Schedule 10, 40 (Optional)
45352 — Roll Set for Copper (Optional)
69667 — Roll Set for 1 1 / " - 1
4
69692 — Roll Set for 2" - 6" AWWA (Optional)
67662 — Adapter Bracket for 300 Compact
76822 — English Diameter Tape
76827 — Metric Diameter Tape
Roll Groover Assembly
Instructions
WARNING
The 916 Roll Groover should only be used with the
following power drives and threading machines.
• 300 Power Drive (38 and 57 RPM)
• 535 Threading Machine (38 and 54 RPM)
• 1822 Threading Machine
• 535 Automatic Threading Machine
• 300 Compact Machine
999-998-693.10_REV. B
1 / "- 6" (1 1 / " - 3" Schedule 40,
4 4
1 / " - 6" (1 1 / " - 3" Schedule 40,
4 4
Weight
lb.
33
34
33
33
33
33
6
6
1 / " AWWA (Optional) 6
2
6
30
0.3
0.3
Use only power drives and threading machines
that operate at 58 RPM or less. Higher speed
machines increase risk of injury.
To prevent serious injury, proper assembly of the
Roll Groover is required. The following procedures
should be followed:
Installing on No. 300 Power Drive
1. Remove carriage or other attachments from the 300
Power Drive.
2. Fully open front chuck of power drive.
3. Position 916 on far side carriage rail and lower onto
near side rail. (Figure 1)
4. Align the notched flats of drive shaft with the jaws on
the No. 300 Power Drive chuck.
5. Tighten front chuck securely on drive shaft.
kg.
15,0
15,5
15,0
15,0
15,0
15,0
Figure 1 – Mounting on No. 300 Power Drive
2,6
2,6
2,6
2,6
Installing Drive Bar Adapter For 1822-I,
13,6
535 or 300 Compact Threading
0,1
0,1
Machines
NOTE! Drive bar adapter must be installed on the 916
Roll Groover when using the 535A, 535M, 1822I
or the 300 Compact Threading Machines as a
power source.
Installing Drive Bar Adapter
1. Install drive bar adapter on roll groover drive shaft.
Align set screws with flats on drive shaft and tighten
screws.
916 Roll Groover
5