Advertisement
Operation Guide 5073
To select a mode
Starting from the regular timekeeping mode, press C to toggle between the regular
timekeeping mode and the World Time setting mode. You can tell what mode is
currently selected by checking the v Day of the Week Hand, as described below.
Regular timekeeping mode
The hand indicates the day of the
week (Su, Mo, Tu, We, Th, Fr, Sa).
Timekeeping
Hand Functions
Regular timekeeping
z Hour Hand
x Second Hand
c Minute Hand
v Day of the Week Hand
b Day
World Time
n World Time Hour Hand: Indicates the current time in
m World Time Minute Hand
•
To return to regular timekeeping from any other mode or function, hold down
about two seconds.
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).
To configure Home City settings
Note
•
This watch does not have a city code that corresponds
to Newfoundland.
1.
In the regular timekeeping mode, keep
(for about five seconds) as the x Second Hand goes
through the following sequence.
•
Moves to the last signal reception result (
to READY (or R for some models), and then to the city
code of the currently selected Home City.
•
This is the city code setting mode.
•
The watch will exit the setting mode automatically if
you do not perform any operation for about two or
three minutes.
•
For details about city codes, see the "City Code
Table".
2.
To change the Home City setting, press
x Second Hand clockwise.
•
Keep pressing
at the city code you want to select as your Home City.
•
Each time you change the city code setting, the
Hour Hand, c Minute Hand and b Day move to
the current time and date for that city code. Do not
perform the next operation until these hands stop
moving.
3.
Press
B to toggle the time for the currently selected city code between STD
(standard time)/DST (daylight saving time).
•
While you are selecting the Home City code, the short end of the
Week Hand will indicate whether the currently selected city code is configured
for standard time (STD) or daylight saving/summer time (DST).
•
Note that you cannot switch between
STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
4.
After all the settings are the way you want, press
timekeeping.
To toggle the Home City time between standard time and daylight saving time
1.
Perform the step 1 under "To configure Home City settings".
•
Each time you select a city code, the
z Hour Hand and c Minute Hand move to
the current time for that city code. Do not perform the next operation until these
hands stop moving.
•
The short end of the
v Day of the Week Hand will indicate whether the currently
selected city code is configured for standard time (STD) or daylight saving/
summer time (DST).
2.
Press
B to toggle the time for the city code of the currently selected Home City
between STD (standard time)/DST (daylight saving time).
•
Note that you cannot switch between
STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
3.
After all the settings are the way you want, press
timekeeping.
World Time setting mode
In the World Time setting mode, the
short end of the hand indicates whether
the time for the currently selected
World Time City is standard time (STD)
or daylight saving/summer time (DST).
the World Time City in 24-hour
format.
C for
A depressed
Y or N), then
D to move the
D until the x Second Hand is pointing
z
v Day of the
A to return to regular
A to return to regular
Note
•
After you specify a city code, the watch will use UTC* offsets to calculate the
World Time based on the current time in your Home City.
*
Coordinated Universal Time, the world-wide scientific standard of timekeeping.
The reference point for UTC is Greenwich, England.
•
Selecting some city codes automatically makes it possible for the watch to
receive the time calibration signal for the corresponding area. See "Radio
Controlled Atomic Timekeeping" for details.
Configuring Current Time and Date Settings Manually
You can configure current time and date settings manually when the watch is unable
to receive a time calibration signal.
To change the current time setting manually
1.
In the regular timekeeping mode, keep
(for about five seconds) as the x Second Hand goes
through the following sequence.
•
Moves to the last signal reception result (
to READY (or R for some models), and then to the city
code of the currently selected Home City.
•
The short end of the
indicate whether the currently selected city code is
configured for standard time (STD) or daylight saving/
summer time (DST).
2.
Change the Home City and daylight saving time (DST)
settings, if you want.
•
For details about these settings, see steps 2 and 3
under "To configure Home City settings".
•
In the following steps, each press of
between settings as shown below.
Home city/DST
3.
Press
C.
•
The
v Day of the Week Hand will move to Su. This is the time setting mode.
•
The
x Second Hand indicates whether the current time is a.m. (A) or p.m. (P).
4.
Use
D (+) and B (–) to change the time (hour and minute) setting.
•
Each press of either button will move the hands (
Hand) to one minute.
•
Holding down
D or B will start high-speed z Hour Hand and c Minute Hand
movement in the applicable direction. To stop high-speed hand movement,
press any button.
•
When setting the time, make sure that the
A (a.m.) or P (p.m.) position for the time you are setting.
•
If you want to change the date setting at this time, press
procedure starting from step 3 under "To change the current date setting
manually".
5.
After the time setting is the way you want, press
timekeeping.
•
This will cause the
x Second Hand to move automatically to 12 o'clock and
resume movement from there.
To change the current date setting manually
00
1.
In the regular timekeeping mode, keep
depressed (for about five seconds) as the
10
x Second Hand goes through the following
sequence.
•
Moves to the last signal reception result (
20
N), then to READY (or R for some models),
and then to the city code of the currently
90
30
selected Home City.
80
40
2.
Press
•
The
of the current year setting. This is the year
70
50
setting mode.
60
•
The year can be set in the range of 2000 to
Setting the year (tens digit)
2099.
3.
Press
until it is pointing at the year tens digit you want
to select.
0
4.
After you select the year tens digit, press
•
The
1
of the current year.
5.
Press
until it is pointing at the year ones digit you want
2
to select.
9
3
6.
After you select the year ones digit, press
•
The
8
4
selected month. This is the month setting
mode.
7
5
6
Setting the year (ones digit)
A depressed
Y or N), then
v Day of the Week Hand will
C cycles
Year
Hour/Minute
(tens digit)
Year
(ones digit)
Day
Month
z Hour Hand and c Minute
x Second Hand is in the correct
C and perform the
A to return to regular
A
Y or
C twice.
x Second Hand will move to the tens digit
D to move the x Second Hand clockwise
C.
x Second Hand will move to the ones digit
D to move the x Second Hand clockwise
C.
x Second Hand will move to the currently
3
Advertisement
