Cerio CS-1005G-4P User Manual

PoE Series CS-1005G-4P
5 Port 10/100/1000M Small Switch with 4 Port PoE+
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received; including
interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A for ITE,
the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the
Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this document
is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be
copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2007, All Rights Reserved.
Unpacking Information
Thank you for purchasing our PoE series products. Before installation,
please check that your package contains the following items.
Open the shipping cartons of the switch and carefully unpack its
contents. The carton should contain the following items:
1. CS-1005G-4P Main Unit x 1
2. AC/DC Power Adapter x 1
3. User's Guide x 1
4. Warranty Card x 1
Application
User's Guide
Introduction
Power Over Ethernet
The CERIO CS-1005G-4P is a powerful and IEEE 802.3af/at
Power over Ethernet which provides DC 44~57V Gigabit over
Ethernet cables high-performance Gigabit Ethernet switch, with all 5
ports capable of 10/100Mbps or 1000Mbps auto-negotiation
operation which means the switch could automatically negotiate with
the connected partners on the network speed and duplex mode. It is
ideal for micro-segmenting large networks into smaller, connected
subnets for improved performance, enabling the bandwidth
demanding multimedia and imaging applications. Moreover, the
10/100/1000Mbps auto-sensing ability provides an easy way to
migrate 10Mbps to 1000Mbps network with no pain.
This switch supports 4 Port 10/100/1000M Gigabit port Power
over Ethernet (PoE+), Power Supply up to 250m(820 feet).Up to
250m PoE distance allows you to expand your network via Ethernet
cable to where there is no power line or outlet but where you want to
fix devices such as APs, IP Cameras or IP Phones, etc.. No longer
need to worry about the complicated cables and long distance which
may cost you a lot of time and money. By integrating the data
transmitting cable and power cord, it eliminates the effort
constructing your network. Over current protection and circuit
shorting protection are also supported to ensure the safety.
Key Features
Complying with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX,

IEEE802.3ab 1000Base-T,IEEE-802.3af PoE ,IEEE802.3at PoE+
5 Ports 10/100/1000Mbps Auto-Negotiation Gigabit Switch , Have 4

Ports PSE/ PoE function compliant with IEEE802.3at class4 (30Watt)
IEEE-802.3af class3 (15.4Watt); IEEE802.3af class 2 (7.5Watt)
Ethernet Extend Mode per port switch control makes transmission

distance up to 250m
Support PoE Power Maximum 30W for share 1~4 PSE/PoE Ports

With bundle Power Adapter have 72Watt for 4 PoE port
Full/Half-Duplex capability on each TX port

Supports Store & Forward architecture and performs forwarding and

filtering
Auto-learning networking configurations

Supporting the flow control: back pressure for Half-duplex and

IEEE 802.3x for Full-duplex mode
Broadcast storm control and supporting store & forward operation

Support Jumbo Frame 9216 byte

Non-blocking & Non-head-of-line blocking full-wire speed forwarding

Supports TP interface Auto MDIX function for auto TX/RX swap

Automatic Source MAC Address Learning and Aging

Supports up to 2K MAC addresses

Up to 1M bits buffer
