Advertisement
Installation
The setup of the switch can be performed using the following steps:
Visually inspect the DC jack and make sure that is fully secured
to the power adapter
Make sure that there is proper heat dissipation from and
adequate ventilation around the Switch. Do not place heavy
objects on the Switch
Cables Installation
The Switch support 5 port 10/100/1000Mbps Gigabit Ethernet ports
and Port 1 – Port 4 are Gigabit PoE Enabled ports, these PoE port will
automatically activate when a compatible terminal is identified. The
Switch will supply power through the Ethernet port to the connected
PoE powered device (PD) For legacy devices that are not compatible,
the PoE port will not offer power to this device. This feature allows
users to freely and safely mix legacy and Power over LAN compatible
devices on their network.
The Switch supports 10Mbs Ethernet or 1000Mbps Gigabit Ethernet
and it runs both in half and full duplex mode using two pair of
Category 5 cable. These RJ45 ports are Auto-MDI type port. The
Switch can auto negotiate the MDI-II or MDI-X type, so you can
connect any RJ-45 cable regardless if it is a standard or crossover
cable.
Gigabit PoE Ports (Port 1~4)
These ports are 802.3af (PoE) and 802.3at(PoE+), the PoE port
will automatically activate when a compatible terminal is
identified. The PoE switch will distribute power through the
Gigabit ethernet ports to the connected PoE device. For devices
that are not compatible, the PoE port will not supply the power to
this device. This feature allows user's to freely and safely utilize
the 802.3af (PoE) and 802.3at(PoE+) for Power over Lan devices
on their network.
Extend PoE Mode Port (Port 1~4)
These ports support extended PoE to 250 meters with 10Mbps data
speeds transfer.
Per ports to control extend mode :
If you need to extend the PoE port to extend mode function,
Please select port 1 ~ 4 DIP switch to "ON" position.
Gigabit Ethernet Port (Port 5)
These ports support network speeds of either 10Mbps or 100Mbps
or 1000Mbps, and can operate in half and full-duplex transfer
modes. These ports also support automatic MDI/MDIX crossover
detection
LED Indicator:
Complete LED indicators displays the status of the PoE Switch and
network status
The front panel LEDs provides instant status feedback, and assists
to monitor and troubleshoot when required.
Power LED
Power : (Power Indicator)
On :
Power On
Off :
Power Off
Max Power. LED
Power : (PoE Alert)
On :
Over PoE Load to 70% Alert budget Warning
Off :
Within PoE Load to 70% Alert budget Warning
PoE LEDs (Port 1 ~ Port 4)
Green:
When the PoE powered device (PD) is connected
and the port distributes power successfully
Off :
When the PoE port has failed, possible reason are:
PoE Power circuit shortage
Power over current:
over the power current of PD's classification Out of
PoE voltage of 44 ~ 57 VDC output
No PoE power device (PD) connected
LINK / ACT Status LEDs (Ports 1~5)
Green ( Port 1~ 4)
The port is 1000M Link / Act connected.
Blinking Green
A valid link is established, and there is data
( Port 1~ 4)
transmitting/receiving.
Amber ( Port 1~ 5)
10/100M Link / Act connected.
Product Specifications
Standards & Hardware Specifications
IEEE 802.3i 10Base-T
IEEE 802.3u 100Base-TX,
Standards
IEEE802.3ab 1000Base-T
Conformance
IEEE 802.3x Flow Control
IEEE 802.3af Power over Ethernet(POE)
IEEE 802.at Power over Ethernet Plus (POE+)
5ports RJ-45 connectors for 10/100/1000Mbps
Port Configuration
(With 4 Port Gigabit PSE/ PoE+ function )
Hardware on/off
Power Switch
DIP 1~4 on / off switch for 250 meters
Hardware DIP Switch
distance with 10Mbps transition PoE extend
mode
Media Access Protocol CSMA / CA
10BASE –T: UTP Cat. 3 or up, 100BASE-TX: UTP
Network Media
Cat. 5 or up, 1000BASE-T: UTP Cat. 5 or up
Transmission Method Store and Forward
MAC Address Table
2K
Built-in Buffer
1M bits
10/100/1000Mbps (Half-duplex),
Data Transfer Rate
20/200/2000Mbps (Full-duplex)
Auto MDI/MDIX
Yes
Per PoE port : PoE Status x 4
Per Gigabit (Link / Act) :Status x 5
LED Indicators
Max. PoE : x 1 (PoE Load greater than 70%
warning)
Per Unit : Power x1
Internal Bus Speed
10Gbps
Environmental & Mechanical Characteristics
PoE Power
55V/1.3A for 60Watt (shared) for all PoE
Budget
Ports (max. with share per Port PoE
Device connected) for Ports 1-4 Only .
Power
2 Watt (max. with no PoE Device connected)
Consumption
Power Requirement
External "up to 72Watt" switch power adapter
Operating
0° to 40° C
Temperature
Storage Temperature -40° to 70° C
Operating Humidity
10% to 90% non-condensing
Storage Humidity
5% to 90% non-condensing
Dimension
121 x 75 x 26 mm
( W x H x D )
Certification
FCC, CE, RoHS-compliant
( PoE Status )
Advertisement
