EWM alpha Q 330 Progress puls HP MM TKM Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.3.6
5.3.7
5.3.8
5.3.9
5.3.10
5.3.11
5.3.12
5.3.13
5.3.14
5.3.15
5.3.16
5.4 TIG welding .................................................................................................................................. 70
5.4.1
5.4.2
5.4.3
5.4.4
5.4.5
5.5 MMA welding ................................................................................................................................ 77
5.5.1
5.5.2
5.5.3
5.5.4
5.5.5
5.5.6
5.6 Access control .............................................................................................................................. 79
5.7 Remote control ............................................................................................................................. 79
5.8 Power-saving mode (Standby) ..................................................................................................... 80
5.9 Interfaces for automation ............................................................................................................. 80
5.9.1
5.9.2
5.9.3
5.9.4
5.10 PC interface ................................................................................................................................. 83
5.11 Special parameters (advanced settings) ...................................................................................... 83
5.11.1
5.12 Aligning the cable resistance ....................................................................................................... 94
5.13 Machine configuration menu ........................................................................................................ 95
4
MIG/MAG operating point ............................................................................................. 43
5.3.6.1 Operating point setting via welding current, material thickness or wire
feed speed ..................................................................................................... 43
5.3.6.2 Arc length correction setting .......................................................................... 43
5.3.6.3 Accessory components for operating point setting ....................................... 43
coldArc / coldArc puls ................................................................................................... 44
forceArc / forceArc puls ................................................................................................ 45
rootArc/rootArc puls ...................................................................................................... 46
pipeSolution .................................................................................................................. 46
Operating modes (functional sequences) ..................................................................... 47
5.3.11.1 Explanation of signs and functions ................................................................ 47
5.3.11.2 MIG/MAG automatic cut-out .......................................................................... 47
MIG/MAG program sequence ("Program steps" mode) ............................................... 60
5.3.12.1 Selection of the program sequence parameter ............................................. 60
5.3.12.2 MIG/MAG overview of parameters ................................................................ 61
5.3.12.3 Example, tack welding (non-latched) ............................................................ 62
5.3.12.4 Example, aluminium tack welding (non-latched special) .............................. 62
5.3.12.5 Example, aluminium welding (latched special) ............................................. 63
5.3.12.6 Example, visible seams (latched super pulse) .............................................. 63
Main program A mode .................................................................................................. 65
5.3.13.1 Selecting parameters (program A) ................................................................ 66
Standard MIG/MAG torch ............................................................................................. 67
MIG/MAG special-torches............................................................................................. 67
5.3.15.1 Program and up/down operation ................................................................... 67
5.3.15.2 Switching between Push/Pull and intermediate drive ................................... 67
Expert menu (MIG/MAG) .............................................................................................. 68
5.3.16.1 Selection ........................................................................................................ 68
Welding torch and workpiece line connection .............................................................. 70
Welding task selection .................................................................................................. 71
5.4.2.1 Welding current setting .................................................................................. 71
TIG arc ignition ............................................................................................................. 71
5.4.3.1 Liftarc ............................................................................................................. 71
Operating modes (functional sequences) ..................................................................... 72
5.4.4.1 Explanation of signs and functions ................................................................ 72
5.4.4.2 TIG automatic cut-out .................................................................................... 72
TIG program sequence ("Program steps" mode) ......................................................... 76
Connecting the electrode holder and workpiece lead .................................................. 77
Welding task selection .................................................................................................. 78
5.5.2.1 Welding current setting .................................................................................. 78
Arcforce......................................................................................................................... 78
Hotstart ......................................................................................................................... 78
Antistick......................................................................................................................... 79
Parameter overview ...................................................................................................... 79
Automation interface ..................................................................................................... 81
Remote control connection socket, 19-pole ................................................................. 82
RINT X12 robot interface .............................................................................................. 82
BUSINT X11 Industrial bus interface ............................................................................ 82
Selecting, changing and saving parameters................................................................. 84
5.11.1.1 Reset to factory settings ................................................................................ 86
5.11.1.2 Special parameters in detail .......................................................................... 86
099-005402-EW501
29.06.2017